2011-2016 FJ Cruiser · Service Manual BRAKE

C1453 Reservoir Level Switch Disconnected

Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012

Also covers:

Versions by build date: Nov 2010 – Jul 2012 from Aug 2012

DESCRIPTION

The brake fluid level warning switch sends the appropriate signal to the skid control ECU when the brake fluid level drops.
DTC Code
DTC Detection Condition
Trouble Area
C1453
With the ECU terminal IG1 voltage at 10 to 14 V, an open in the brake fluid level warning switch circuit continues for 2 seconds or more.
  1. Brake fluid level
  2. Brake fluid level warning switch (Brake master cylinder reservoir assembly)
  3. Harness or connector
  4. Master cylinder solenoid (Skid control ECU)
C1454
The fluid level of the reservoir is LOW for 40 seconds after the ignition switch is turned to ON, or for 7 seconds during pump motor operation.

WIRING DIAGRAM

C187573E06

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).


1. CHECK BRAKE FLUID LEVEL
  1. Turn the ignition switch off.

  1. Depress the brake pedal 40 times or more (until the pedal reaction feels light and pedal stroke becomes longer).

  1. Check the amount of fluid in the brake reservoir.

    HINT:
    When the ignition switch is turned to ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm (0.197 in.) from the level when the ignition switch is off (normal).

    OK:
    Brake fluid level is normal.



NG
CHECK AND REPAIR BRAKE FLUID LEAKAGE
OK


2. INSPECT BRAKE FLUID LEVEL WARNING SWITCH
  1. Disconnect the A14 brake fluid level warning switch connector.

  1. C217215E01
    Measure the resistance according to the value(s) in the table below.

    HINT:
    A float is placed inside the reservoir. Its position can be changed by increasing/decreasing the level of brake fluid.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (GND) - 2 (LBL)
    Float UP (Switch off)
    1.9 to 2.1 kΩ
    Float DOWN (Switch on)
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Brake Fluid Level Warning Switch)

    HINT:
    If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)
  1. Disconnect the A4 skid control ECU connector.

  1. Disconnect the A14 brake fluid level warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-41 (LBL) - A14-2 (LBL)
    Always
    Below 1 Ω
    A4-41 (LBL) - Body ground
    Always
    10 kΩ or higher
    A14-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine and idle it for approximately 40 seconds.

  1. Check if the same DTCs are output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)


← C1452 Accumulator Low Pressure (from Aug 2012)C1453 Reservoir Level Switch Disconnected (+ C1454) (from Aug 2012) →