2011-2016 FJ Cruiser · Service Manual HEATER & AIR CONDITIONING SYSTEM

TERMINALS OF ECU

System information · Vehicles built from Aug 2014

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2014 Aug 2012 – Jul 2014 from Aug 2014


INSPECT AIR CONDITIONER AMPLIFIER ASSEMBLY

  1. Disconnect the E32 and E33 connectors from the air conditioning amplifier assembly and inspect the connector on the wire harness side, as shown in the table below.
    I102676E01

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E32-1 (IG+) - E32-20 (GND)
    Y-R - W-B
    Power source (IG)
    Ignition switch: off → ON
    Below 1 V → 11 to 14 V
    E32-9 (SG-4) - Body ground
    GR-R - Body ground
    Ground for A/C evaporator temperature sensor
    Always
    Below 1 Ω
    E32-11 (B) - E32-20 (GND)
    W-R - W-B
    Power source (Back-up)
    Always
    11 to 14 V
    E32-20 (GND) - Body ground
    W-B - Body ground
    Ground for main power supply
    Always
    Below 1 Ω
    E33-1 (VER1) - Body ground
    G-W - Body ground
    Destination judgment signal
    Always
    Below 1 Ω
    E33-6 (SG-3) - Body ground
    G-Y - Body ground
    Ground for lock sensor
    Always
    Below 1 Ω
    E33-16 (TAMG) - Body ground
    GR - Body ground
    Ground for ambient temperature sensor
    Always
    Below 1 Ω
    E33-17 (SG-1) - Body ground
    V-G - Body ground
    Ground for mode control servo motor
    Always
    Below 1 Ω
    E33-18 (SG-2) - Body ground
    Y-G - Body ground
    Ground for air mix control servomotor
    Always
    Below 1 Ω

  2. Reconnect the E32 and E33 connectors to the air conditioning amplifier assembly and inspect the wire harness side connector from the back side, as shown in the table below.
    I102675E01

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E32-1 (IG+) - Body ground
    Y-R - Body ground
    Power source (IG)
    Ignition switch: off → ON
    Below 1 V → 11 to 14 V
    E32-4 (MGC) - E32-20 (GND)
    LG-B - W-B
    Magnet clutch relay signal
    Engine idling
    Operate A/C system
    Magnet clutch: OFF → ON
    11 to 14 V → Below 1 V
    E32-5 (RDFG) - E32-20 (GND)
    Y-V - W-B
    Defogger switch signal
    Ignition switch: ON
    Defogger switch: OFF → ON
    11 to 14 V → Below 1 V
    E32-6 (FRS) - E32-20 (GND)
    V - W-B
    Recirculation/Fresh switch signal
    Ignition switch: ON
    Recirculation/Fresh switch:
    RECIRCULATION → FRESH
    11 to 14 V → Below 1 V
    E32-7 (REC) - E32-20 (GND)
    P-B - W-B
    Recirculation/Fresh switch signal
    Ignition switch: ON
    Recirculation/Fresh switch:
    FRESH → RECIRCULATION
    11 to 14 V → Below 1 V
    E32-8 (BLW) - E32-20 (GND)
    Y - W-B
    Blower switch signal
    Ignition switch: ON
    Blower switch: ON
    OFF → ON (LO, M1, M2, HI)
    11 to 14 V → Below 1 V
    E32-9 (SG-4) - Body ground
    GR-R - Body ground
    Ground for A/C evaporator temperature sensor
    Always
    Below 1 Ω
    E32-10 (TE) - E32-9 (SG-4)
    B - GR-R
    A/C evaporator temperature sensor signal
    Ignition switch: ON
    Evaporator temperature:
    0 → 15°C (32 → 59°F)
    1.7 to 2.1 V → 0.9 to 1.3 V
    E32-11 (B) - Body ground
    W-R - Body ground
    Power source (Back-up)
    Always
    11 to 14 V
    E32-20 (GND) - Body ground
    W-B - Body ground
    Ground for main power supply
    Always
    Below 1 Ω
    E33-6 (SG-3) - Body ground
    G-Y - Body ground
    Ground for lock sensor
    Always
    Below 1 Ω
    E33-7 (S5-1) - E33-18 (SG-2)
    P-B - Y-G
    Power supply for air mix control servomotor
    Ignition switch: off → ON
    Below 1 V → 4.5 to 5.5 V
    E33-8 (LOCK) - E33-6 (SG-3)
    R-W - G-Y
    Magnet clutch signal
    Start engine
    Operate A/C system
    Magnet clutch: ON
    Pulse generation
    (See waveform 1)
    E33-9 (DEF) - E32-20 (GND)
    LG - W-B
    Mode switch signal
    Ignition switch: ON
    Mode select switch:
    Except DEF → DEF
    Below 1.5 V → 11 to 14 V
    E33-13 (TAM) - E33-16 (TAMG)
    B-Y - GR
    Ambient temperature sensor signal
    Ignition switch: ON
    Ambient temperature:
    25 → 40°C (77 → 104°F)
    1.7 to 2.1 V → 1.3 to 1.8 V
    E33-16 (TAMG) - Body ground
    GR - Body ground
    Ground for ambient temperature sensor
    Always
    Below 1 Ω
    E33-17 (SG-1) - Body ground
    V-G - Body ground
    Ground for mode control servo motor
    Always
    Below 1 Ω
    E33-18 (SG-2) - Body ground
    Y-G - Body ground
    Ground for air mix control servomotor
    Always
    Below 1 Ω
    E33-19 (S5) - E33-17 (SG-1)
    P - V-G
    Power supply for mode control servo motor
    Ignition switch: off → ON
    Below 1 V → 4.5 to 5.5 V
    E33-22 (PSW) - E32-20 (GND)
    LG-R - W-B
    A/C pressure switch signal
    Start engine
    Operate A/C system
    Refrigerant pressure: Normal (Less than 0.196 MPa (2.0 kgf/cm2)) or more than 3.14 MPa (32.0 kgf/cm2))
    11 to 14 V → Below 1 V
    E33-24 (AC1) - E32-20 (GND)
    G-W - W-B
    Idle up request signal
    Engine idling
    Operate A/C system
    Magnet clutch: OFF → ON
    11 to 14 V → Below 1 V
    If the results are not as specified, replace the air conditioning amplifier assembly with a new one. If the results are still not as specified after replacing the air conditioning control assembly, inspect the circuits connected to other parts.

    1. I045420E01
      WAVEFORM 1:
      Magnet clutch signal 
      ECM Terminal Names
      Between E33-8 (LOCK) - E33-6 (SG-3)
      Tester Ranges
      0.2 V/DIV, 10 msec./DIV
      Conditions
      Start engine
      Operate A/C system
      Magnet clutch: ON

      HINT:
      The wavelength becomes shorter as the engine rpm increases.


INSPECT ECM

  1. Connect the connector to the ECM and inspect the wire harness side connector from the back side, as shown in the table below.
    C213108E06

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E81-25 (AC1) - B49-12 (E1)
    G-W - BR
    Idle-up request signal
    Start engine
    A/C magnet clutch is engaged → not engaged
    Below 1 V → 11 to 14 V
    E81-27 (ACT) - B49-12 (E1)
    L-W - BR
    Magnet clutch ON
    permit signal
    Start engine
    Operate A/C system
    A/C switch OFF Blower switch OFF → A/C switch ON Blower switch ON
    Below 1 V → 11 to 14 V
    E81-36 (THWO) - B49-12 (E1)*1
    BR-B - BR
    Engine coolant temperature sensor signal
    Engine idling
    Engine coolant temperature 80°C (176°F)
    Pulse generation
    (See waveform 1)
    E82-19 (THWO) - B49-12 (E1)*2
    1. *1: w/ Secondary Air Injection System
    2. *2: w/o Secondary Air Injection System
    If the result is not as specified, the ECM may have a malfunction.

    1. E219622E01
      WAVEFORM 1:
      Magnet clutch signal 
      ECM Terminal Names
      Between E82-19 (THWO) - B49-12 (E1)
      Tester Ranges
      0.2 V/DIV, 10 msec./DIV
      Conditions
      Engine idling
      Engine coolant temperature 80°C (176°F)

      HINT:
      The wavelength becomes shorter as the engine rpm increases.

← TERMINALS OF ECU (Aug 2012 – Jul 2014)ON-VEHICLE INSPECTION (from Jul 2007) →