Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2102    Throttle Actuator Control Motor Circuit Low

DTC    P2103    Throttle Actuator Control Motor Circuit High

for Preparation Click here


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.
The opening angle of the throttle valve is detected by the Throttle Position (TP) sensor, which is mounted on the throttle with motor body assembly. The TP sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:
This ETCS (Electronic Throttle Control System) does not use a throttle cable.


DTC No.
DTC Detection Condition
Trouble Area
P2102
Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic):
  1. (a) Throttle actuator duty ratio exceeds 80% or more
  2. (b) Throttle actuator current is less than 0.5 A
  1. Open in throttle actuator circuit
  2. Throttle actuator
  3. ECM
P2103
Either of the following conditions is met (1 trip detection logic):
  1. Motor driver IC high current inhibit signal on
  2. Motor driver IC high current limiter monitor input fails
  1. Short in throttle actuator circuit
  2. Throttle actuator
  3. Throttle valve
  4. Throttle with motor body assembly
  5. ECM

MONITOR DESCRIPTION

The ECM monitors the electrical current through the electronic actuator, and detects malfunctions and open circuits in the throttle actuator based on this value. If the current is outside the standard range, the ECM determines that there is a malfunction in the throttle actuator. In addition, if the throttle valve does not function properly (for example, stuck on), the ECM determines that there is a malfunction. The ECM then illuminates the MIL and stores a DTC.
Example:
  1. When the electrical current is less than 0.5 A and the throttle actuator duty ratio exceeds 80%, the ECM interprets this as the current being outside the standard range, and illuminates the MIL and stores DTC.
  2. If the malfunction is not repaired successfully, a DTC is stored when the engine is quickly revved up to a high rpm several times after the engine has idled for 5 seconds after engine start.

MONITOR STRATEGY


Related DTCs
P2102: Throttle actuator current (low current)
P2103: Throttle actuator current (high current)
Required Sensors/Components (Main)
Throttle actuator (Throttle with motor body assembly)
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
2 seconds: P2102
25 times: P2103 (Case 1)
0.6 seconds: P2103 (Case 2)
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None

P2102 
Command to electronic throttle actuator
ON
Output duty cycle
80% or more
Electronic throttle actuator power supply voltage
8 V or more
|Motor current - Last motor current|
Less than 0.2 A

P2103 
Battery voltage
8 V or more
Starter
OFF
Command to electronic throttle actuator
ON
Either of the following conditions 1 or 2 met:
-
1. Electronic throttle actuator power supply voltage
8 V or more
2. Command to electronic throttle actuator power
ON

TYPICAL MALFUNCTION THRESHOLDS


P2102 
Motor current
Less than 0.5 A

P2103 (Case 1) 
Motor driver IC high current limiter monitor input
Fail

P2103 (Case 2) 
Motor driver IC high current inhibit signal
ON

CONFIRMATION DRIVING PATTERN


A199313E11

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine.
  7. With the vehicle stationary, fully depress the accelerator pedal and quickly release it [B].
  8. Check that 16 seconds or more have elapsed from the instant when the accelerator pedal is first depressed.
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  10. Read DTCs.

    HINT:
    1. If a DTC is output, the system is malfunctioning.
    2. If a DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P2102 or P2103.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again.

  14. If no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


FAIL-SAFE

When any of these DTCs or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM


A115950E05


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
  2. The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Open Duty / Throttle Motor Close Duty) can be read using the Techstream. However the ECM shuts off the throttle actuator current when the ETCS malfunctions.

1.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
A059778E83
  1. Disconnect the B14 throttle with motor body connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (M+) - 1 (M-)
    20°C (68°F)
    0.3 to 100 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Throttle with Motor Body Assembly)

    HINT:
    Perform "Inspection After Repair" after replacing the throttle with motor body assembly (Click here).



NG
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (THROTTLE WITH MOTOR BODY ASSEMBLY - ECM)
  1. Disconnect the B14 throttle with motor body connector.

  1. Disconnect the B50 and B49 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B14-2 (M+) - B50-20 (M+)
    Always
    Below 1 Ω
    B14-1 (M-) - B49-29 (M-)
    Always
    Below 1 Ω
    B14-2 (M+) or B50-20 (M+) - Body ground
    Always
    10 kΩ or higher
    B14-1 (M-) or B49-29 (M-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
  1. Check for foreign objects between the throttle valve and the housing.

    OK:
    No foreign objects between throttle valve and housing.

    HINT:
    Perform "Inspection After Repair" after cleaning the throttle with motor body assembly (Click here).



NG
REMOVE FOREIGN OBJECT AND CLEAN THROTTLE WITH MOTOR BODY ASSEMBLY
OK


4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)
  1. Check if the throttle valve opens and closes smoothly.

    OK:
    Throttle valve opens and closes smoothly.

    HINT:
    Perform "Inspection After Repair" after replacing the throttle with motor body assembly (Click here).



NG
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
OK

REPLACE ECM (Click here)