SFI SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | The speed is indicated on speedometer. |
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 16383 rpm | 650 to 750 rpm: Idling | - |
| Calculate Load | Calculated load by ECM/ Min.: 0%, Max.: 100% |
| - |
| Vehicle Load | Vehicle load/ Min.: 0%, Max.: 25700% | Actual vehicle load | - |
| MAF | Air flow rate from Mass Air Flow (MAF) meter/ Min.: 0 gm/sec, Max.: 655.35 gm/sec | 2.5 to 4.7 gm/sec: Idling 18.3 to 25.8 gm/sec: 3000 rpm | If the mass air flow volume is approximately 0.0 gm/sec:
|
| Atmosphere Pressure | Atmospheric pressure/ Min.: 0 kPa (0 mmHg), Max.: 255 kPa (1912 mmHg) | Equivalent to atmospheric pressure (absolute pressure) | - |
| Coolant Temp | Engine coolant temperature/ Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | If the value is -40°C (-40°F): the sensor circuit is open. If the value is higher than 135°C (275°F): the sensor circuit is shorted. |
| Intake Air | Intake air temperature/ Min.: -40°C (-40°F), Max.: 140°C (284°F) | Equivalent to ambient air temperature | If the value is -40°C (-40°F): the sensor circuit is open. If the value is higher than 128°C (262°F): the sensor circuit is shorted. |
| Engine Run Time | Engine run time/ Min.: 0 s, Max.: 65535 s | Time after engine start | Service data. |
| Initial Engine Coolant Temp | Initial engine coolant temperature/ Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) | Coolant temperature when engine started | Service data. |
| Initial Intake Air Temp | Initial intake air temperature/ Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) | Intake air temperature when engine started | Service data. |
| Battery Voltage | Battery voltage/ Min.: 0 V, Max.: 65.535 V | 11 to 14 V: Idling | - |
| Glow Indicator Supported*1 | Glow indicator supported/ Unsupp or Supp | - | - |
| Glow Indicator*1 | Glow indicator/ ON or OFF | - | - |
| Accelerator Position | Accelerator pedal position/ Min.: 0%, Max.: 399.9% | Actual accelerator pedal position | - |
| Accel Sens. No.1 Volt % | Absolute Accelerator Pedal Position (APP) No. 1/ Min.: 0%, Max.: 100% | 10 to 22%: accelerator pedal released 52 to 90%: accelerator pedal fully depressed | - |
| Accel Sens. No.2 Volt % | Absolute APP No. 2/ Min.: 0%, Max.: 100% | 24 to 40%: accelerator pedal released 68 to 95%: accelerator pedal fully depressed | - |
| Accel Sensor Out No.1 | APP sensor No. 1 voltage/ Min.: 0 V, Max.: 4.98 V | 0.5 to 1.1 V: accelerator pedal released 2.6 to 4.5 V: accelerator pedal fully depressed | - |
| Accel Sensor Out No.2 | APP sensor No. 2 voltage/ Min.: 0 V, Max.: 4.98 V | 1.2 to 2.0 V: accelerator pedal released 3.4 to 4.75 V: accelerator pedal fully depressed | - |
| Accelerator Idle Position | Whether or not accelerator pedal position sensor detecting idle/ ON or OFF | ON: Idling | - |
| Accel Fully Close Learn #1 | Accelerator fully closed learning value No. 1/ Min.: 0 deg, Max.: 124.5 deg | - | ETCS service data. |
| Accel Fully Close Learn #2 | Accelerator fully closed learning value No. 2/ Min.: 0 deg, Max.: 124.5 deg | - | ETCS service data. |
| Throttle Sensor Volt % | Throttle valve opening percentage according to throttle position sensor/ Min.: 0%, Max.: 100% |
| Value calculated based on the voltage at terminal VTA1. |
| Throttl Sensor #2 Volt % | Throttle valve opening percentage according to throttle position sensor No. 2/ Min.: 0%, Max.: 100% |
| Value calculated based on the voltage at terminal VTA2. |
| ST1 | Brake pedal signal/ ON or OFF | ON: Brake pedal depressed | - |
| System Guard | System guard/ ON or OFF | - | ETCS service data. |
| Open Side Malfunction | Open side malfunction/ ON or OFF | - | ETCS service data. |
| Throttle Idle Position | Whether or not throttle position sensor detecting idling ON or OFF |
| - |
| Throttle Require Position | Required throttle position/ Min.: 0 V, Max.: 4.98 V | 0.5 to 1.1 V: Idling | - |
| Throttle Sensor Position*5 | Throttle position sensor/ Min.: 0%, Max.: 100% |
| Recognition value for throttle opening angle on ECM. |
| Throttle Position No. 1 | Throttle position sensor No. 1 output voltage/ Min.: 0 V, Max.: 4.98 V |
| - |
| Throttle Position No. 2 | Throttle position sensor No. 2 output voltage/ Min.: 0 V, Max.: 4.98 V |
| - |
| Throttle Position Command | Throttle position command value/ Min.: 0 V, Max.: 4.98 V | 0.5 to 4.8 V | - |
| Throttle Sens Open Pos #1 | Throttle sensor opener position No. 1/ Min.: 0 V, Max.: 4.98 V | 0.6 to 1.4 V | ETCS service data. |
| Throttle Sens Open Pos #2 | Throttle sensor opener position No. 2/ Min.: 0 V, Max.: 4.98 V | 1.7 to 2.5 V | ETCS service data. |
| Throttle Motor Current | Throttle motor current/ Min.: 0 A, Max.: 19.9 A | 0 to 3.0 A: Idling | ETCS service data. |
| Throttle Motor DUTY | Throttle actuator/ Min.: 0%, Max.: 100% | 10 to 22%: Idling after engine warmed up | ETCS service data. |
| Throttle Motor Duty (Open) | Throttle actuator duty ratio (open)/ Min.: 0%, Max.: 255% | 0 to 40%: Idling | ETCS service data. |
| Throttle Motor Duty (Close) | Throttle actuator duty ratio (closed)/ Min.: 0%, Max.: 255% | 0 to 40%: Idling | ETCS service data. |
| Throttle Fully Close Learn | Throttle valve fully closed (learned value)/ Min.: 0 V, Max.: 4.98 V | 0.4 to 1.0 V: Accelerator pedal released | - |
| +BM Voltage | +BM voltage/ Min.: 0 V, Max.: 79.998 V | 11 to 14 V: Ignition switch ON and system normal | ETCS service data. |
| Actuator Power Supply | Actuator power supply/ ON or OFF | ON: Idling | ETCS service data. |
| Throttle Position | Throttle valve opening angle/ Min.: 0 deg, Max.: 499.99 deg | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| ISC Flow | Flow rate calculated using information from each sensor/ Min.: 0 L/s, Max.: 79.99 L/s | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| ISC Position | Requested opening amount calculated using ISC control/ Min.: 0 deg, Max.: 499.99 deg | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. This is the throttle valve opening amount while the engine is idling (the throttle valve opening amount necessary to maintain ISC air flow). |
| ISC Feedback Value | ISC feedback compensation amount/ Min.: -40 L/s, Max.: 39.99 L/s | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| ISC Learning Value | ISC learned compensation amount/ Min.: -40 L/s, Max.: 39.99 L/s | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Electric Load Feedback Val | Compensation flow rate according to electrical load/ Min.: -40 L/s, Max.: 39.99 L/s | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Air Conditioner FB Val | Compensation flow rate according to air conditioner load/ Min.: -40 L/s, Max.: 39.99 L/s | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| PS Feedback Val | Power steering load feedback value: Min.: -40 L/s, Max.: 39.99 L/s | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Low Revolution Control | Low engine speed control operation state/ ON or OFF | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Neutral Control | N position control status/ ON or OFF | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| N Range Status*1 | Shift lever N status/ ON or OFF | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Eng Stall Control FB Flow | Intake air compensation flow rate/ Min.: -40 L/s, Max.: 39.99 L/s | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Deposit Loss Flow | Flow loss due to deposits/ Min.: -40 L/s, Max.: 39.99 L/s | - |
|
| Fuel Pump Duty*3 | Fuel pump duty/ Min.: 0%, Max.: 399.9% | - | - |
| Injector (Port) | Injection period of the No. 1 cylinder/ Min.: 0 μs, Max.: 65535 μs | 1600 to 2700 μs: idling | - |
| Injection Volum (Cylinder 1) | Injection volume (cylinder 1)/ Min.: 0 ml, Max.: 2.047 ml | 0.005 to 0.015 ml | Quantity of fuel injection volume for 10 times. |
| Fuel Pump/Speed Status*4 | Fuel pump/speed status/ ON or OFF | - | - |
| Vacuum Pump*3 | Key-off EVAP system leak detection pump status/ ON or OFF | - | - |
| Current Fuel Type | Current fuel type | - | Identifying the current fuel type: Gasoline |
| EVAP (Purge) VSV | Purge VSV control duty/ Min.: 0%, Max.: 100% | 0 to 100%: During idling | Command signal from ECM. |
| Evap Purge Flow | Purge flow/ Min.: 0%, Max.: 399.9% | 0 to 100%: Idling | - |
| Purge Density Learn Value | Learning value of purge density/ Min.: -200, Max.: 199.993 | Idling: -35 to 1 | Service data. |
| Vapor Pressure Pump*3 | Vapor pressure/ Min.: 0 kPa (0 mmHg), Max.: 1441.77 kPa (10814.17 mmHg) | Near atmosphere pressure: Fuel cap removed | Pressure inside fuel tank monitored by vapor pressure sensor. |
| Vapor Pressure (Calculated)*3 | Vapor pressure (calculated)/ Min.: -720.896 kPa (-5407.17 mmHg), Max.: 720.874 kPa (5407.002 mmHg) | Near atmosphere pressure: Fuel cap removed | Pressure inside fuel tank monitored by vapor pressure sensor. |
| EVAP System Vent Valve*3 | Key-off EVAP system vent valve status/ ON or OFF | - | - |
| EVAP Purge VSV | VSV status for EVAP control/ ON or OFF | - | - |
| Purge Cut VSV Duty | Purge cut VSV duty/ Min.: 0%, Max.: 399.9% | - | - |
| Target Air-Fuel Ratio | Air fuel ratio: Min.: 0, Max.: 1.999 | 0.8 to 1.2: During idling | - |
| AF Lambda B1S1 | Short-term fuel trim associated with the Bank 1 Sensor 1/ Min.: 0, Max.: 1.999 |
| - |
| AF Lambda B2S1 | Short-term fuel trim associated with the Bank 2 Sensor 1/ Min.: 0, Max.: 1.999 |
| - |
| AFS Voltage B1S1 | Air fuel ratio sensor output voltage (for Bank 1 Sensor 1)/ Min.: 0 V, Max.: 7.999 V | 2.8 to 3.8 V: Idling | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor. |
| AFS Voltage B2S1 | Air fuel ratio sensor output voltage (for Bank 2 Sensor 1)/ Min.: 0 V, Max.: 7.999 V | 2.8 to 3.8 V: Idling | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor. |
| AFS Current B1S1 | Air fuel ratio sensor current Bank 1 Sensor 1/ Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor. |
| AFS Current B2S1 | Air fuel ratio sensor current (for Bank 2 Sensor 1)/ Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor. |
| A/F Heater Duty #1 | A/F heater duty ratio (for Bank 1) Min.: 0%, Max.: 399.9% | 0 to 100% | - |
| A/F Heater Duty #2 | A/F heater duty ratio (for Bank 2) Min.: 0%, Max.: 399.9% | 0 to 100% | - |
| O2S B1S2 | Heated oxygen sensor output voltage (for Bank 1 Sensor 2)/ Min.: 0 V, Max.: 1.275 V | 0.1 to 0.9 V: Driving 70 km/h (44 mph) | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor. |
| O2S B2S2 | Heated oxygen sensor output voltage (for Bank 2 Sensor 2)/ Min.: 0 V, Max.: 1.275 V | 0.1 to 0.9 V: Driving 70 km/h (44 mph) | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor. |
| O2S Impedance B1S2*3 | Sub heated oxygen sensor impedance (Bank 1 Sensor 2)/ Min.: 0 ohm, Max.: 21247.67 ohm | 5 to 15000 ohm | After driving for approx. 10 min. in an urban area. |
| O2S Impedance B2S2*3 | Sub heated oxygen sensor impedance (Bank 2 Sensor 2)/ Min.: 0 ohm, Max.: 21247.67 ohm | 5 to 15000 ohm | After driving for approx. 10 min. in an urban area. |
| O2 Heater B1S2 | Heated oxygen sensor heater for bank 1 sensor 2/ Not Act or Active | - | - |
| O2 Heater B2S2 | Heated oxygen sensor heater for bank 2 sensor 2/ Not Act or Active | - | - |
| O2 Heater Curr Val B1S2 | Heated oxygen sensor current for bank 1 sensor 2/ Min.: 0 A, Max.: 4.999 A | - | - |
| O2 Heater Curr Val B2S2 | Heated oxygen sensor current for bank 2 sensor 2/ Min.: 0 A, Max.: 4.999 A | - | - |
| Short FT #1 | Short-term fuel trim of Bank 1/ Min.: -100%, Max.: 99.2% | -15 to 15% | This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air fuel ratio. |
| Long FT #1 | Long-term fuel trim of Bank 1/ Min.: -100%, Max.: 99.2% | -15 to 15% |
|
| A/F Learn Value Idle #1 | Air fuel ratio learn value area of idle (for Bank 1)/ Min.: -50%, Max.: 49.6% | - | Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher). |
| A/F Learn Value Low #1 | Air fuel ratio learn value area of low load (for Bank 1)/ Min.: -50%, Max.: 49.6% | - | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid1 #1 | Air fuel ratio learn value area of middle load 1 (for Bank 1)/ Min.: -50%, Max.: 49.6% | - | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid2 #1 | Air fuel ratio learn value area of middle load 2 (for Bank 1)/ Min.: -50%, Max.: 49.6% | - | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value High #1 | Air fuel ratio learn value area of high load (for Bank 1)/ Min.: -50%, Max.: 49.6% | - | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts). |
| Total FT #1 | Total fuel trim of bank 1 Min.: -0.5, Max.: 0.496 | -0.28 to 0.2: Idling | - |
| Short FT #2 | Short-term fuel trim of Bank 2/ Min.: -100%, Max.: 99.2% | -15 to 15% | This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air fuel ratio. |
| Long FT #2 | Long-term fuel trim of Bank 2/ Min.: -100%, Max.: 99.2% | -15 to 15% |
|
| A/F Learn Value Idle #2 | Air fuel ratio learn value area of idle (for Bank 2)/ Min.: -50%, Max.: 49.6% | - | Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher). |
| A/F Learn Value Low #2 | Air fuel ratio learn value area of low load (for Bank 2)/ Min.: -50%, Max.: 49.6% | - | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid1 #2 | Air fuel ratio learn value area of middle load 1 (for Bank 2)/ Min.: -50%, Max.: 49.6% | - | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid2 #2 | Air fuel ratio learn value area of middle load 2 (for Bank 2)/ Min.: -50%, Max.: 49.6% | - | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value High #2 | Air fuel ratio learn value area of high load (for Bank 2)/ Min.: -50%, Max.: 49.6% | - | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts). |
| Total FT #2 | Total fuel trim of bank 2 Min.: -0.5, Max.: 0.496 | -0.28 to 0.2: Idling | - |
| Fuel System Status #1 | Fuel system status (Bank 1)/ OL, CL, OLDrive, OLFault or CLFault | CL: Idling after warming up |
|
| Fuel System Status #2 | Fuel system status (Bank 2)/ OL, CL, OLDrive, OLFault or CLFault | CL: Idling after warming up |
|
| Air pump pressure (Absolute)*3 | Air pump pressure Bank 1 (absolute)/ Min.: 0 kPa (0 mmHg), Max.: 65535 kPa (491553 mmHg) | Atmospheric pressure +1 kPa (7.5 mmHg) or more: Air pump assembly on, emission control valve set open Close to atmospheric pressure: Air pump assembly off, emission control valve set closed | Refer to DTC P2431 (Click here) |
| Air Pump2 Pressure (Absolute)*3 | Air pump pressure Bank 2 (absolute)/ Min.: 0 kPa (0 mmHg), Max.: 65535 kPa (491553 mmHg) | Atmospheric pressure +1 kPa (7.5 mmHg) or more: Air pump assembly on, emission control valve set open Close to atmospheric pressure: Air pump assembly off, emission control valve set closed | Refer to DTC P2431 (Click here) |
| Air Pump Pulsation Pressure*3 | Air pump pulsation pressure Bank 1/ Min.: 0 kPa (0 mmHg), Max.: 655.35 kPa (4915.53 mmHg) | - | Cumulative pulsation pressure calculated by ECM (Click here) |
| Secondary Air Control VSV*3 | Secondary air injection system status/ ON or OFF | ON: Secondary air injection system operation | - |
| 2nd Air System Status*3 | Secondary air system status/ ON or OFF | ON: Secondary air system operation | - |
| AI Test*3 | AI operation prohibition/ READY or NOT RDY | READY | - |
| Subfreezing Conditions*3 | Subfreezing conditions status/ ON or OFF | - | - |
| Air Pump Heater*3 | Air pump heater status/ ON or OFF | - | Active Test support data. |
| IGN Advance | Ignition timing advance for No. 1 cylinder/ Min.: -64 deg, Max.: 63.5 deg | BTDC 7 to 24°: Idling | - |
| Knock Feedback Value | Feedback value of knocking/ Min.: -1024 deg(CA), Max.: 1023.9 deg(CA) | -22 to 0 deg(CA): Driving, 70 km/h (44 mph) | Service data. |
| Knock Correct Learn Value | Correction learning value of knocking/ Min.: -1024 deg(CA), Max.: 1023.9 deg(CA) | 0 to 22 deg(CA): Driving, 70 km/h (44 mph) | Service data. |
| Idle Spark Advn Ctrl #1 | Individual cylinder timing advance compensation amount (No. 1)/ Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Idle Spark Advn Ctrl #2 | Individual cylinder timing advance compensation amount (No. 2)/ Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Idle Spark Advn Ctrl #3 | Individual cylinder timing advance compensation amount (No. 3)/ Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Idle Spark Advn Ctrl #4 | Individual cylinder timing advance compensation amount (No. 4)/ Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Idle Spark Advn Ctrl #5 | Individual cylinder timing advance compensation amount (No. 5)/ Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Idle Spark Advn Ctrl #6 | Individual cylinder timing advance compensation amount (No. 6)/ Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| VVT Control Status #1 | Variable valve timing (VVT) control status (Bank 1)/ ON or OFF | - | - |
| VVT Control Status #2 | VVT control status (Bank 2)/ ON or OFF | - | - |
| VVT Advance Fail | VVT control failure status/ ON or OFF | ON: VVT control failure | - |
| VVT Aim Angle #1*6 | VVT aim angle (Bank 1)/ Min.: 0%, Max.: 399.9% | 0 to 80% | VVT duty signal value during intrusive operation. |
| VVT Change Angle #1*6 | VVT change angle (Bank 1)/ Min.: 0 DegFR, Max.: 639.9 DegFR | 0 DegFR: Idling | Displacement angle during intrusive operation. |
| VVT OCV Duty #1*6 | VVT OCV operation duty (Bank 1)/ Min.: 0%, Max.: 399.9% | 0 to 100% | Requested duty value for intrusive operation. |
| VVT Aim Angle #2*6 | VVT aim angle (Bank 2)/ Min.: 0%, Max.: 399.9% | 0 to 80% | VVT duty signal value during intrusive operation. |
| VVT Change Angle #2*6 | VVT change angle (Bank 2)/ Min.: 0 DegFR, Max.: 639.9 DegFR | 0 DegFR: Idling | Displacement angle during intrusive operation. |
| VVT OCV Duty #2*6 | VVT OCV operation duty (Bank 2)/ Min.: 0%, Max.: 399.9% | 0 to 100% | Requested duty value for intrusive operation. |
| VVT Ex Hold Lrn Val #1*6 | VVT exhaust hold duty ratio learning value (Bank 1)/ Min.: 0%, Max.: 399.9% | 0 to 80% | VVT duty signal value during intrusive operation. |
| VVT Ex Chg Angle #1*6 | VVT exhaust change angle (Bank 1)/ Min.: 0 DegFR, Max.: 639.9 DegFR | 0 to 5 DegFR: Idling | Displacement angle during intrusive operation. |
| VVT Ex OCV Duty #1*6 | VVT exhaust OCV duty (Bank 1)/ Min.: 0%, Max.: 399.9% | 0 to 100% | Requested duty value for intrusive operation. |
| VVT Ex Hold Lrn Val #2*6 | VVT exhaust hold duty ratio learning value (Bank 2)/ Min.: 0%, Max.: 399.9% | 0 to 80% | VVT duty signal value during intrusive operation. |
| VVT Ex Chg Angle #2*6 | VVT exhaust change angle (Bank 2)/ Min.: 0 DegFR, Max.: 639.9 DegFR | 0 to 5 DegFR: Idling | Displacement angle during intrusive operation. |
| VVT Ex OCV Duty #2*6 | VVT exhaust OCV duty (Bank 2)/ Min.: 0%, Max.: 399.9% | 0 to 100% | Requested duty value for intrusive operation. |
| VN Turbo Type | Variable nozzle turbo type/ Not Avl or Commo or Vacuum or CAN Com | Not Avl (Unused) | - |
| Catalyst Temp B1S1 | Catalyst temperature (Bank 1, Sensor 1)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Catalyst Temp B2S1 | Catalyst temperature (Bank 2, Sensor 1)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Catalyst Temp B1S2 | Catalyst temperature (Bank 1, Sensor 2)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Catalyst Temp B2S2 | Catalyst temperature (Bank 2, Sensor 2)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Starter Signal | Starter signal/ ON or OFF | ON: Cranking | - |
| Power Steering Signal | Power steering switch signal/ ON or OFF | ON: Power steering operation | - |
| Neutral Position SW Signal*1 | PNP switch status/ ON or OFF | ON: Shift lever in P or N | - |
| Clutch Switch*2 | Clutch Switch/ ON or OFF | ON: Clutch pedal depressed | - |
| Transfer Neutral*1 | Transfer neutral status: ON or OFF | ON: Transfer in neutral | - |
| 4WD SW | 4WD switch ON or OFF | ON: 4WD ON | - |
| Transfer L4 | Transfer L4 switch ON or OFF | ON: Transfer L4 ON | - |
| Stop Light Switch | Stop light switch/ ON or OFF | ON: Brake pedal depressed | - |
| A/C Signal | A/C switch status/ ON or OFF | ON: A/C ON | - |
| Closed Throttle Position SW | Closed throttle position switch/ ON or OFF |
| - |
| Fuel Cut Condition | Fuel cut condition/ ON or OFF | ON: Fuel cut operating | - |
| Immobiliser Communication | Immobiliser communication/ ON or OFF | ON: Normal | - |
| Check Mode | Check mode/ ON or OFF | ON: Check mode ON | Refer to the Check Mode Procedure (Click here). |
| SPD Test Result | Check mode result for vehicle speed sensor/ Compl or Incmpl | - | - |
| AS Test Result*3 | Check mode result for secondary air injection system/ Compl or Incmpl | - | - |
| Misfire Test Result | Check mode result for misfire monitor/ Compl or Incmpl | - | - |
| OXS1 Test Result | Check mode result for heated oxygen sensor (Bank 1)/ Compl or Incmpl | - | - |
| OXS2 Test Result | Check mode result for heated oxygen sensor (Bank 2)/ Compl or Incmpl | - | - |
| A/F Test Results #2 | Check mode result for air fuel ratio sensor (Bank 2)/ Compl or Incmpl | - | - |
| A/F Test Results #1 | Check mode result for air fuel ratio sensor (Bank 1)/ Compl or Incmpl | - | - |
| Complete Parts Monitor | Comprehensive component monitor/ Not Avl or Avail | - | - |
| Fuel System Monitor | Fuel system monitor/ Not Avl or Avail | - | - |
| Misfire Monitor | Misfire monitor/ Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor/ Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor/ Compl or Incmpl | - | - |
| A/C Monitor | A/C Monitor/ Not Avl or Avail | - | - |
| A/C Monitor | A/C Monitor/ Compl or Incmpl | - | - |
| 2nd Air Monitor | 2nd air monitor/ Not Avl or Avail | - | - |
| 2nd Air Monitor | 2nd air monitor/ Compl or Incmpl | - | - |
| EVAP Monitor | EVAP monitor/ Not Avl or Avail | - | - |
| EVAP Monitor | EVAP monitor/ Compl or Incmpl | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor/ Not Avl or Avail | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor/ Compl or Incmpl | - | - |
| Catalyst Monitor | Catalyst monitor/ Not Avl or Avail | - | - |
| Catalyst Monitor | Catalyst monitor/ Compl or Incmpl | - | - |
| Component Monitor ENA | Comprehensive component monitor/ Unable or Enable | - | - |
| Component Monitor CMPL | Comprehensive component monitor/ Compl or Incmpl | - | - |
| Fuel System Monitor ENA | Fuel system monitor/ Unable or Enable | - | - |
| Fuel System Monitor CMPL | Fuel system monitor/ Compl or Incmpl | - | - |
| Misfire Monitor ENA | Misfire monitor/ Unable or Enable | - | - |
| Misfire Monitor CMPL | Misfire monitor/ Compl or Incmpl | - | - |
| EGR/VVT Monitor ENA | EGR monitor/ Unable or Enable | - | - |
| EGR/VVT Monitor CMPL | EGR monitor/ Compl or Incmpl | - | - |
| Heater Monitor ENA | O2S (A/FS) heater monitor/ Unable or Enable | - | - |
| Heater Monitor CMPL | O2S (A/FS) heater monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Monitor ENA | O2S (A/FS) monitor/ Unable or Enable | - | - |
| O2S(A/FS) Monitor CMPL | O2S (A/FS) monitor/ Compl or Incmpl | - | - |
| A/C Monitor ENA | A/C monitor/ Unable or Enable | - | - |
| A/C Monitor CMPL | A/C monitor/ Compl or Incmpl | - | - |
| 2nd Air Monitor ENA | 2nd air monitor/ Unable or Enable | - | - |
| 2nd Air Monitor CMPL | 2nd air monitor/ Compl or Incmpl | - | - |
| EVAP Monitor ENA | EVAP monitor/ Unable or Enable | - | - |
| EVAP Monitor CMPL | EVAP monitor/ Compl or Incmpl | - | - |
| Heated Cat Monitor ENA | Heated catalyst monitor/ Unable or Enable | - | - |
| Heated Cat Monitor CMPL | Heated catalyst monitor/ Compl or Incmpl | - | - |
| Catalyst Monitor ENA | Catalyst monitor/ Unable or Enable | - | - |
| Catalyst Monitor CMPL | Catalyst monitor/ Compl or Incmpl | - | - |
| TC Terminal | TC terminal status/ ON or OFF | - | - |
| # Codes (Include History) | Number of codes/ Min.: 0, Max.: 255 | - | Number of stored DTCs. |
| MIL | MIL status/ ON or OFF | ON: MIL on | - |
| MIL ON Run Distance | MIL on run distance/ Min.: 0 km, Max.: 65535 km | Distance after DTC stored (MIL turns on) | - |
| Running Time from MIL ON | Running time from MIL on/ Min.: 0 min, Max.: 65535 min | Equivalent to running time after MIL on | - |
| Time after DTC Cleared | Time after DTC cleared/ Min.: 0 min, Max.: 65535 min | Equivalent to time after DTCs cleared | - |
| Distance from DTC Cleared | Distance after DTC cleared/ Min.: 0 km, Max.: 65535 km | Equivalent to drive distance after DTCs cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycle after DTC cleared/ Min.: 0, Max.: 255 | - | Number of warm-up cycles after the DTC is cleared. |
| Dist Batt Cable Disconnect | Distance from battery cable disconnected/ Min.: 0 km, Max.: 65535 km | - | - |
| IG OFF Elapsed Time*3 | Time after ignition switch off/ Min.: 0 min, Max.: 655350 min | - | - |
| OBD Requirements | OBD requirement | OBD II (California ARB) | - |
| Number of Emission DTC | Emission related DTCs Min.: 0, Max.: 127 | - | Number of emission related DTCs. |
| TC and TE1 | TC and TE1 terminal of DLC3/ ON or OFF | - | - |
| Ignition Trig. Count | Ignition counter/ Min.: 0, Max.: 65535 | 0 to 600 | - |
| Cylinder #1 Misfire Count to Cylinder #6 Misfire Count | Misfire count of the cylinder 1 to 6/ Min.: 0, Max.: 255 | 0 | - |
| All Cylinders Misfire Count | All cylinders misfire count/ Min.: 0, Max.: 255 | 0 | - |
| Misfire RPM | Engine speed for first misfire range/ Min.: 0 rpm, Max.: 6375 rpm | 0 rpm: Misfire 0 | - |
| Misfire Load | Engine load for first misfire range/ Min.: 0 g/rev, Max.: 3.98 g/rev | 0 g/rev: Misfire 0 | - |
| Misfire Margin | Misfire monitoring/ Min.: -128%, Max.: 127% | 0 to 99.2% | Misfire detection margin |
| Catalyst OT MF F/C | Catalyst over temperature misfire prevention F/C/ Not Avl or Avail | Avail: Cat OT MF F/C available Not Avl: Cat OT MF F/C not available | - |
| Cat OT MF F/C History | Catalyst over temperature misfire prevention F/C history/ ON or OFF | OFF: Fuel cut operation history does not exist | - |
| Cat OT MF F/C Cylinder #1 | Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut operating | - |
| Cat OT MF F/C Cylinder #2 | Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut operating | - |
| Cat OT MF F/C Cylinder #3 | Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut operating | - |
| Cat OT MF F/C Cylinder #4 | Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut operating | - |
| Cat OT MF F/C Cylinder #5 | Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut operating | - |
| Cat OT MF F/C Cylinder #6 | Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut operating | - |
| Engine Speed (Starter Off) | Engine speed when starter off/ Min.: 0 rpm, Max.: 51199 rpm | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Starter Count | Number of times starter turned on after ignition switch turned to ON/ Min.: 0, Max.: 255 | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Run Dist of Previous Trip | Distance driven during previous trip/ Min.: 0 km, Max.: 655.35 km | - | Before 5 seconds elapse after starting the engine, which is DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal. HINT: Run Dist of Previous Trip in freeze frame data which were present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of Data List (real-time measurements), or for freeze frame data which were present when the DTCs other than P1604 were detected, the value indicates the distance driven during the current trip. |
| Engine Starting Time | Time elapsed after engine started (interval between ignition switch ON and off)/ Min.: 0 ms, Max.: 655350 ms | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Previous Trip Coolant Temp | Engine coolant temperature during previous trip/ Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Previous Trip Intake Temp | Intake air temperature during previous trip/ Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Engine Oil Temperature | Engine oil temperature (estimated temperature)/ Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Previous Trip Eng Oil Temp | Engine oil temperature during previous trip/ Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Ambient Temp for A/C | Ambient temperature Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Previous Trip Ambient Temp | Ambient temperature during previous trip/ Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Engine Start Hesitation | History of hesitation during engine start/ ON or OFF | - | - |
| Low Rev for Eng Start | History of low engine speed after engine start/ ON or OFF | - | - |
| Minimum Engine Speed | Minimum engine speed/ Min.: 0 rpm, Max.: 51199 rpm | - | Reference: Check the value when engine stalls, is difficult to start, or idles roughly. |
| Power Steering Pressure | Power steering oil pressure/ Min.: 0 MPa, Max.: 25.599 MPa | - | - |
| ACT VSV | A/C cut status for Active Test/ ON or OFF | - | - |
| Brake Override System | Brake Override System Status/ ON or OFF | ON: Brake override system operation | - |
| Electric Cooling Fan Low*3 | Electric fan motor operation status/ ON or OFF | ON: Cooling fan operated at low speed | - |
| Idle Fuel Cut | Fuel cut idle/ ON or OFF | ON: Fuel cut operation | Idle Fuel Cut is "ON" when the throttle valve is fully closed and the engine speed is more than 2800 rpm. |
| FC TAU | Fuel cut TAU: Fuel cut during very light load/ ON or OFF | ON: Fuel cut operation | The fuel cut being performed under a very light load to prevent the engine combustion from becoming incomplete. |
| Immobiliser Fuel Cut | Status of the immobiliser fuel cut/ ON or OFF | - | - |
| Immobiliser Fuel Cut History | Status of the immobiliser fuel cut history/ ON or OFF | - | - |
| Electrical Load Signal 1 | Electrical load signal/ ON or OFF | - | - |
| Electrical Load Signal 2 | Electrical load signal/ ON or OFF | - | - |
| Model Code | Model code | - | Identifying the model code: GSJ1#. |
| Engine Type | Engine type | - | Identifying the engine type: 1GRFE. |
| Cylinder Number | Number of cylinders/ Min.: 0, Max.: 255 | - | Identifying the number of cylinders: 6. |
| Transmission Type | Transmission type | - | Identifying the transmission type: ECT 5th or MT. |
| Destination | Destination | - | Identifying the destination: A (America). |
| Model Year | Model year/ Min.: 1900, Max.: 2155 | - | Identifying the model year: 20##. |
| System Identification | System identification | - | Identifying the engine system: Gasoline (gasoline engine). |
| Engine Speed of Cyl #1 | Engine speed for cylinder 1/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #2 | Engine speed for cylinder 2/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #3 | Engine speed for cylinder 3/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #4 | Engine speed for cylinder 4/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #5 | Engine speed for cylinder 5/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #6 | Engine speed for cylinder 6/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Av Engine Speed of All Cyl | Engine speed for all cylinders/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| A/F Sensor Determination (worst value) #1*3 | Worst judgment value of air fuel ratio sensor output (Bank 1)/ Min.: -1, Max.: 0.99 | 0.00 |
|
| A/F Sensor Determination (worst value) #2*3 | Worst judgment value of air fuel ratio sensor output (Bank 2)/ Min.: -1, Max.: 0.99 | 0.00 |
|
| Engine Speed Fluctuation Avg (worst value) #1*3 | Worst value of average engine speed fluctuation (Cylinder 1)/ Min.: 0, Max.: 2.55 | 0.00 |
|
| Engine Speed Fluctuation Avg (worst value) #2*3 | Worst value of average engine speed fluctuation (Cylinder 2)/ Min.: 0, Max.: 2.55 | 0.00 |
|
| Engine Speed Fluctuation Avg (worst value) #3*3 | Worst value of average engine speed fluctuation (Cylinder 3)/ Min.: 0, Max.: 2.55 | 0.00 |
|
| Engine Speed Fluctuation Avg (worst value) #4*3 | Worst value of average engine speed fluctuation (Cylinder 4)/ Min.: 0, Max.: 2.55 | 0.00 |
|
| Engine Speed Fluctuation Avg (worst value) #5*3 | Worst value of average engine speed fluctuation (Cylinder 5)/ Min.: 0, Max.: 2.55 | 0.00 |
|
| Engine Speed Fluctuation Avg (worst value) #6*3 | Worst value of average engine speed fluctuation (Cylinder 6)/ Min.: 0, Max.: 2.55 | 0.00 |
|
| SPD (NT)*1 | Input shaft speed/ Min.: 0 rpm, Max.: 12750 rpm | Lock-up is
| Data is displayed in increments of 50 rpm. |
| SPD (SP2)*1 | Output shaft speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed) | - |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Injection Volume | Change injection volume | Between -12.5% and 24.8% |
|
| Control the Injection Volume for A/F Sensor | Change injection volume | -12.5%/0%/12.5% |
|
| Activate the VSV for Secondary Air Control*1 | Activate the secondary air system | ON/OFF |
|
| Activate the VSV for Evap Control | Activate purge VSV control | ON/OFF | - |
| Control the A/C Cut Signal | Control A/C cut signal | ON/OFF | Test possible when following
|
| Control the Fuel Pump / Speed | Activate fuel pump | ON/OFF | This test is possible when the following
|
| Control the Fuel Pump Duty*1 | Activate fuel pump | 25%/80% | Test possible when following
|
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON/OFF |
|
| Control the Idle Fuel Cut Prohibit | Prohibit idling fuel cut control | ON/OFF | - |
| Prohibit the Catalyst OT Misfire prevent F/C | Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire | ON/OFF ON: Fuel cut is prohibited | Confirm that the vehicle is stopped and the engine speed is 3000 rpm or less. |
| Control the ETCS Open/Close Slow Speed | Throttle actuator | Close/Open Open: throttle valve opens slowly | This test is possible when the following conditions are met:
|
| Control the ETCS Open/Close Fast Speed | Throttle actuator | Close/Open Open: throttle valve opens fast | This test is possible when the following conditions are met:
|
| Control the VVT Linear (Bank 1) | Control VVT (for intake camshaft of bank 1) | -128 to 127% This value added to present OCV control duty 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT System (Bank 1) | Turn on and off Oil Control Valve (bank 1) | ON/OFF |
|
| Control the VVT Linear (Bank 2) | Control VVT (for intake camshaft of bank 2) | -128 to 127% This value added to present OCV control duty 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT System (Bank 2) | Turn on and off Oil Control Valve (bank 2) | ON/OFF |
|
| Control the VVT Exhaust Linear (Bank 1) | Control VVT (for exhaust camshaft of bank 1) | -128 to 127% This value added to present OCV control duty 100%: Maximum retard -100%: Maximum advance |
|
| Control the VVT Exhaust Linear (Bank 2) | Control VVT (for exhaust camshaft of bank 2) | -128 to 127% This value added to present OCV control duty 100%: Maximum retard -100%: Maximum advance |
|
| Activate the Vacuum Pump*1 | Activate leak detection pump | ON/OFF | - |
| Activate the VSV for Vent Valve*1 | Activate vent valve | ON/OFF | - |
| Activate the Air Pump Heater*1 | Activate air pump heater | ON/OFF |
|
| Control the Select Cylinder Fuel Cut | Selected cylinder (cylinder #1 to #6) injector fuel cut | #1/#2/#3/#4/#5/#6 ON/OFF | Test is possible while vehicle is stopped and engine is idling.*2 |
| Control the All Cylinders Fuel Cut | All cylinder fuel cut | ON/OFF | Test is possible while vehicle is stopped and engine is idling.*2 |
| Check the Cylinder Compression*3 | Check the cylinder compression pressure | ON/OFF | Fuel injection and ignition stop in all cylinders. |
| SYSTEM CHECK |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility.
Perform the System Check by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Notes |
| Evaporative System Check (Automatic Mode) | Perform 6 steps in order to operate EVAP key-off monitor automatically | 35°C (95°F) or less |
|
| Evaporative System Check (Manual Mode) | Perform 6 steps in order to operate EVAP key-off monitor manually | 35°C (95°F) or less |
|
| Secondary Air Injection Check Automatic Mode) | Perform secondary air injection system operation automatically | With warm engine, ignition switch turned off once |
|
| Secondary Air Injection Check (Manual Mode) | Perform 5 operations in order to operate secondary air injection system monitor manually | With warm engine, ignition switch turned off once |
|