Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2444    Secondary Air Injection System Pump Stuck On Bank1

DTC    P2445    Secondary Air Injection System Pump Stuck Off Bank1

for Preparation Click here


DESCRIPTION

Refer to P0412 .

DTC No.
DTC Detection Condition
Trouble Area
P2444
Both of the following conditions are met for 7 seconds (2 trip detection logic):
(a) Engine is running
(b) Secondary air injection pressure is 2.5 kPa (18.7 mmHg) or more when secondary air injection is OFF
  1. Short in air pump assembly circuit
  2. Open or short in pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (for bank 2)) circuit
  3. Pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (for bank 2))
  4. Air injection control driver
  5. ECM
P2445
Both of the following conditions are met for 7 seconds (2 trip detection logic):
(a) Engine is running
(b) Secondary air injection pressure is less than 1 kPa (7.5 mmHg) when secondary air injection is ON
  1. Air pump assembly
  2. Open in air pump assembly circuit
  3. Secondary air injection system piping
  4. Open or short in pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (for bank 2)) circuit
  5. Pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (for bank 2))
  6. Air injection control driver
  7. ECM
  8. Open or short in air pump heater circuit
  9. Air pump heater relay (AIR PMP HTR)

MONITOR DESCRIPTION

The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the emission control valve set of the secondary air injection system. The sensor measures the pressure in the secondary air passage and transmits a signal to the ECM.
If either of the following conditions occurs, the ECM interprets it as a malfunction of the secondary air injection system, and illuminates the MIL and stores a DTC:
  1. The pressure indicated by the pressure sensor does not reach threshold levels despite the ECM turning on the air pump assembly.
  2. The pressure indicated by the pressure sensor exceeds threshold levels despite the ECM turning off the air pump assembly.
Example:
  1. DTC P2444 mainly indicates a malfunction in which the air pump assembly is stuck on.
  2. DTC P2445 mainly indicate a malfunction in which the air pump assembly is stuck off.

MONITOR STRATEGY


Related DTCs
P2444: Air pump stuck ON
P2445: Air pump stuck OFF
Required Sensors/Components (Main)
Pressure sensor (Emission control valve set)
Required Sensors/Components (Related)
-
Frequency of Operation
Once per driving cycle
Duration
7 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not stored
P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - advance)
P0012, P0022 (VVT system - retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - advance)
P0015, P0025 (Exhaust VVT system - retard)
P0016, P0018 (VVT system - misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120 - P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P014C - P014F, P015A - P015D, P2195 - P2198, P2237 - P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0306 (Misfire)
P0327, P0328, P0332, P0333 (Knock sensor)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351 - P0356 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0451 - P0453 (EVAP system)
P0500, P0722 (Vehicle speed sensor)
P106B (Evap. emission control system pressure sensor - Air injection system pressure sensor correlation)
P219A, P219B (Air-fuel ratio imbalance)
P2431 - P2433, P2436 - P2438 (Secondary air injection system pressure sensor)
Battery voltage
11 V or higher
Atmospheric pressure
45 kPa (338 mmHg) or higher
Engine
Running
Pressure pattern check during secondary air injection ON*1
Completed
Pressure pattern check during secondary air injection OFF*2
Completed
Pressure change check: secondary air injection ON*3
Completed
Pressure pulsation check: secondary air injection OFF*4
Completed
Air injection control driver failure (open/short or out of range)
Not detected
Secondary air injection pressure sensor failure (open/short or out of range)
Not detected

*1: Pressure pattern check during secondary air injection ON
-
Time after secondary air injection starts operation
5 seconds or more
Air pump
ON
Emission control valve
Open
Engine speed
Less than 3750 rpm
Engine speed
680 rpm or more
Intake air amount
Less than 100 gm/sec
Time after engine started
5 seconds or more

*2: Pressure pattern check during secondary air injection OFF
-
Time after secondary air injection starts operation
10 seconds or more
Air pump
OFF
Emission control valve
Closed
Engine speed
Less than 3000 rpm
Secondary air injection monitor during secondary air injection ON
Completed
Time after engine started
5 seconds or more

*3: Pressure change check: secondary air injection ON
-
Secondary air injection
Operating
Air pump
ON
Emission control valve (bank 2)
Open
Emission control valve (bank 1)
Closed
Secondary air injection pressure sensor failure (open/short or out of range)
Not detected
Intake air amount
Less than 15 gm/sec

*4: Pressure pulsation check: secondary air injection OFF
-
Pressure change check: secondary air injection ON
Completed
Pressure pulsation check: secondary air injection OFF
Not completed
Air pump
ON
Time after emission control valve (bank 2) closes
0.3 seconds or more
Emission control valve (bank 1)
Open
Engine speed
Less than 5000 rpm

TYPICAL MALFUNCTION THRESHOLDS


P2444 Air Pump is Stuck ON 
Either condition is met
(a) or (b)
(a) Condition 1 (secondary air injection OFF)
-
(b) Condition 3 (secondary air injection OFF)
-

P2445 Air Pump is Stuck OFF 
Either condition is met
(a) or (b)
(a) Condition 2 (secondary air injection ON)
-
(b) Condition 4 (secondary air injection ON)
-

Secondary Air Injection ON (Condition 1) 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
1.25 kPa (9.3 mmHg) or higher
Secondary air injection pressure
1 kPa (7.5 mmHg) or higher

Secondary Air Injection ON (Condition 2) 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
1.25 kPa (9.3 mmHg) or higher
Secondary air injection pressure
Below 1 kPa (7.5 mmHg)

Secondary Air Injection ON (Condition 3) 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
Below 1.25 kPa (9.3 mmHg)
Secondary air injection pressure
1 kPa (7.5 mmHg) or higher

Secondary Air Injection ON (Condition 4) 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
Below 1.25 kPa (9.3 mmHg)
Secondary air injection pressure
Below 1 kPa (7.5 mmHg)

Secondary Air Injection OFF (Condition 1) 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
10 kPa (75 mmHg) or higher
Secondary air injection pressure
2.5 kPa (18.7 mmHg) or higher

Secondary Air Injection OFF (Condition 2) 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
10 kPa (75 mmHg) or higher
Secondary air injection pressure
Below 2.5 kPa (18.7 mmHg)

Secondary Air Injection OFF (Condition 3) 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
Below 10 kPa (75 mmHg)
Secondary air injection pressure
2.5 kPa (18.7 mmHg) or higher

Secondary Air Injection OFF (Condition 4) 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
Below 10 kPa (75 mmHg)
Secondary air injection pressure
Below 2.5 kPa (18.7 mmHg)

HINT:
Refer to "Data List / Active Test" [Air Pump Pressure (Absolute), Air Pump2 Pressure (Absolute) and Air Pump Pulsation Pressure] (Click here).


MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

NOTICE:
  1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
  2. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
  3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
  4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  1. Start the engine and warm it up.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the Techstream on.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
  10. Start the engine after the Techstream initialization is finished.
  11. Perform the System Check operation by pressing Next.
  12. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
  13. Enter the following menus: Powertrain / Engine and ECT / Trouble codes.
  14. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  15. After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  16. Input the DTC: P2444 or P2445.
  17. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  18. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If no permanent DTC is output, the system is normal.
    2. If a permanent DTC is output, the system is malfunctioning.

  19. Turn the ignition switch off.

WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

HINT:
Determination by ECM monitoring:
The ECM detects malfunctions in the secondary air injection system by detecting the pressure in the secondary air injection passage between the air pump assembly and emission control valve set and stores a DTC. Soon after a cold engine start, the monitor runs for a short time while the secondary air injection system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.
The following 8 patterns are secondary air injection system pressure conditions in the secondary air injection system passage.


Pressure Condition in Secondary Air Injection System Case 1 
Air Pump Assembly
ON
Emission Control Valve Set
Open
Pressure
1 kPa (7.5 mmHg) or higher
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 2 
Air Pump Assembly
OFF
Emission Control Valve Set
Open
Pressure
Below 2.5 kPa (18.7 mmHg)
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 3 
Air Pump Assembly
ON
Emission Control Valve Set
Closed
Pressure
1 kPa (7.5 mmHg) or higher
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 4 
Air Pump Assembly
OFF
Emission Control Valve Set
Closed
Pressure
Below 2.5 kPa (18.7 mmHg)
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 5 
Air Pump Assembly
ON
Emission Control Valve Set
Open
Pressure
1 kPa (7.5 mmHg) or higher
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 6 
Air Pump Assembly
OFF
Emission Control Valve Set
Open
Pressure
Below 2.5 kPa (18.7 mmHg)
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 7 
Air Pump Assembly
ON
Emission Control Valve Set
Closed
Pressure
1 kPa (7.5 mmHg) or higher
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 8 
Air Pump Assembly
OFF
Emission Control Valve Set
Closed
Pressure
Below 2.5 kPa (18.7 mmHg)
Pulsation Detection
Exhaust gas pulsation not detected
If the detected pressure is high, the air pump assembly is assumed to be ON, and if it alternates sharply, the emission control valve set is assumed to be open. The ECM detects malfunctions from the combination of pressures detected when the secondary air injection system is ON and OFF.

HINT:
The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.

HINT:
  1. In cases 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the emission control valve, the average pressure is higher than in case 1 (approximately 15 to 25 kPa (112.5 to 187.5 mmHg)).
  2. In case 1, the average pressure is approximately 3 to 11 kPa (22.5 to 82.5 mmHg)). The value of 1 kPa indicated in the table above is a threshold for detecting pump malfunctions.


Detected Condition while Secondary Air Injection Operating:
Air Pump Assembly ON, Emission Control Valve Set Open
Detected Condition while Secondary Air Injection not Operating:
Air Pump Assembly OFF, Emission Control Valve Set Closed
ECM Determination
DTC Output
Case 1
Case 8
Normal
-
Case 1
Case 6
Emission control valve set stuck open
P2440
or
P2442
Case 1
Case 7
Air pump assembly stuck ON
P2444
Case 2
Case 8
Air pump assembly stuck OFF
P2445
Case 3
Case 8
Emission control valve set stuck closed
P2441
or
P2443
Case 1
Case 5
Emission control valve set stuck open and air pump assembly stuck ON
P2440 and/or P2442
and
P2444
Case 2
Case 6
Emission control valve set stuck open and air pump assembly stuck OFF
P2440 and/or P2442
and
P2445
Case 3
Case 7
Emission control valve set stuck closed and air pump assembly stuck ON
P2441 and/or P2443
and
P2444
Case 4
Case 8
Emission control valve set stuck closed and air pump assembly stuck OFF
P2441 and/or P2443
and
P2445

HINT:
  1. By using the Techstream to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, pending codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

  1. System Check:

    NOTICE:
    1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
    2. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  2. The pressure in the secondary air passage can be checked using the Techstream.
    1. Start the engine and warm it up.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the Techstream on.
    6. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN and AIR PUMP: OFF, ASV1 CLOSE, ASV2 CLOSE.

      HINT:
      When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

    7. Start the engine.
    8. Perform the secondary air injection system forced operation while the engine is idling.
    9. Check that the Data List values for the air pump (AIR PUMP), emission control valve (ASV) and pressure in the secondary air injection system passage (PRESSURE) displayed on the Techstream are as shown in the table below.

      Standard:

      Techstream Operation
      Air Pump Assembly
      Emission Control Valve Set
      Pressure*1
      Pulsation*2
      AIR PUMP: ON, ASV: OPEN
      ON
      OPEN
      1 kPa (7.5 mmHg) or higher
      1.25 kPa (9.3 mmHg) or higher
      AIR PUMP: OFF, ASV: CLOSE
      OFF
      CLOSE
      Below 2.5 kPa (18.7 mmHg)
      Below 10 kPa (7.5 mmHg)

      *1: Average pumping pressure (gauge pressure). The pressure should be 1 kPa or higher when the secondary air injection system operates.
      *2: The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.
    10. Turn the ignition switch off.

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  2. Bank 2 refers to the bank that does not include the No. 1 cylinder.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2444 AND/OR P2445)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P2444 and/or P2445 is output
    A
    P2444 and/or P2445 and P0418 are output
    B
    P2444 and/or P2445 and other DTCs (except P0418) are output
    C

    HINT:
    If any DTCs other than P0418, P2444 and P2445 are output, troubleshoot those DTCs first.



B
GO TO AIR PUMP INSPECTION PROCEDURE

C
GO TO DTC CHART (Click here)
A


2.CHECK FREEZE FRAME DATA (AIR PUMP FREEZE, AIR SWITCHING VALVE FREEZE AND AIR SWITCHING VALVE2 FREEZE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Read the values of Air Pump Freeze, Air Switching Valve Freeze and Air Switching Valve2 Freeze from the freeze frame data recorded previously.

  1. Referring to the following table, proceed to the appropriate step according to the result of the data reading.

    Result 
    Result
    Proceed to
    Air Pump Freeze
    Air Switching Valve Freeze
    Air Switching Valve2 Freeze
    OFF
    OFF
    OFF
    B
    Except above
    A



B
Go to step 8
A


3.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVE THE AIR PUMP HEATER)


    A221585E10
  1. Disconnect the air pump assembly connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT/ Active Test / Activate the Air Pump Heater.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A36-1 (APH+) - Body ground
    Activate the Air Pump Heater is ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Pump Assembly)



NG
Go to step 5
OK


4.INSPECT AIR PUMP ASSEMBLY (HEATER RESISTANCE)
  1. Inspect the air pump assembly (Click here).



NG
REPLACE AIR PUMP ASSEMBLY (Click here)
OK


5.INSPECT AIR PUMP HEATER RELAY (AIR PMP HTR)
  1. Inspect the air pump heater relay (AIR PMP HTR) .



NG
REPLACE AIR PUMP HEATER RELAY (AIR PMP HTR)
OK


6.CHECK AIR PUMP HEATER RELAY (AIR PMP HTR) (POWER SOURCE)
  1. Remove the air pump heater relay (AIR PMP HTR) from the engine room relay block.



    A287418E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    5 (Air pump heater relay (AIR PMP HTR)) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    Air Pump Heater Relay (AIR PMP HTR)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (AIR PUMP ASSEMBLY - AIR PUMP HEATER RELAY (AIR PMP HTR), BODY GROUND)
  1. Remove the air pump heater relay (AIR PMP HTR) from the engine room relay block.

  1. Disconnect the A36 air pump assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3 (Air pump heater relay (AIR PMP HTR)) - A36-1 (APH+)
    Always
    Below 1 Ω
    A36-3 (APHG) - Body ground
    Always
    Below 1 Ω
    3 (Air pump heater relay (AIR PMP HTR)) or A36-1 (APH+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN and AIR PUMP: OFF, ASV1: CLOSE, ASV2: CLOSE.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system forced operation while the engine is idling.

  1. Check that the Data List values for the air pump (AIR PUMP), emission control valve (ASV) and pressure in the secondary air injection system passage (PRESSURE) displayed on the Techstream are as shown in the table below.

    Standard:

    Techstream Operation
    Air Pump
    Emission Control Valve
    PRESSURE*
    AIR PUMP: ON, ASV: OPEN
    ON
    ON
    1 kPa (7.5 mmHg) or higher [A]
    AIR PUMP: OFF, ASV: CLOSE
    OFF
    OFF
    Below 2.5 kPa (18.7 mmHg) [B]

    *: Average pumping pressure. The pressure should be 1 kPa or higher when the secondary air injection system operates.

    Standard:
    The pressures for [A] and [B] should differ by 1 kPa (7.5 mmHg) or more.

  1. Turn the ignition switch off.

    NOTICE:
    1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
    2. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
Go to step 10
OK


9.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2245)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (if stored) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble codes.

  1. Read pending DTCs.

  1. Turn the ignition switch off.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

    Result 
    Result
    Proceed to
    P2444 and/or P2445 is output
    A
    No pending DTC is output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


10.INSPECT EMISSION CONTROL VALVE SET (PRESSURE SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute).

  1. Check the pressure displayed on the Techstream.

    Standard pressure:
    45.63 to 135 kPa (342 to 1013 mmHg)

    HINT:
    The Techstream displays the air pump pressure as absolute pressure.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Bank 1)
    B
    NG (for Bank 2)
    C



B
REPLACE EMISSION CONTROL VALVE SET (Click here)

C
REPLACE NO. 2 EMISSION CONTROL VALVE SET (Click here)
A


11.CHECK SECONDARY AIR INJECTION SYSTEM PIPE CONNECTIONS

A287408

  1. Check that all the pipes and hoses between the air pump and emission control valve are securely connected.

  1. Inspect the pipes and hoses for blockages and damage.

    OK:
    Secondary air injection system piping has no blockages or damage.



NG
REPAIR OR REPLACE SECONDARY AIR INJECTION SYSTEM PIPING
OK


12.INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT)
A221587E11
  1. Disconnect the A38 and A37 air injection control driver connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A37-1 (E) - Body ground
    Always
    Below 1 Ω

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A38-1 (BATT) - Body ground
    Always
    11 to 14 V (near battery voltage)
    A37-5 (+B) - Body ground
    Ignition switch ON
    11 to 14 V (near battery voltage)

Text in Illustration 
*a
Front view of wire harness connector
(to Air Injection Control Driver)


NG
REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT
OK


13.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
  1. Disconnect the B48 ECM connector.

  1. Disconnect the A37 air injection control driver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B48-23 (AIRP) - A37-4 (SIP)
    Always
    Below 1 Ω
    B48-23 (AIRP) or A37-4 (SIP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.CHECK AIR PUMP ASSEMBLY
  1. Inspect the air pump assembly (Click here).



OK
Go to step 17

NG
Go to step 15

15.REPLACE AIR PUMP ASSEMBLY
  1. Replace the air pump assembly (Click here).


NEXT


16.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (if stored) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble codes.

  1. Read pending DTCs.

    OK:
    No pending DTC is output.

  1. Turn the ignition switch off.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
Go to step 17
OK

END 

17.PERFORM ACTIVE TEST USING TECHSTREAM


    A229922E40
  1. Disconnect the air injection control driver connector.

  1. Connect terminals DI and SIV of the wire harness connector for the air injection control driver.
    Text in Illustration 
    *1
    Air Injection Control Driver
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Air Injection Control Driver)

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system forced operation while the engine is idling.

  1. Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is ON and OFF.

  1. Turn the ignition switch off.

    NOTICE:
    1. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    A37-3 (SIV) - A37-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    A37-3 (SIV) - A37-1 (E)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V



    A229922E41
  1. Connect terminals DI and SIP of the wire harness connector for the air injection control driver.
    Text in Illustration 
    *1
    Air Injection Control Driver
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Air Injection Control Driver)

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system forced operation while the engine is idling.

  1. Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is ON and OFF.

  1. Turn the ignition switch off.

    NOTICE:
    1. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    A37-4 (SIP) - A37-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    A37-4 (SIP) - A37-1 (E)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V



NG
REPLACE ECM (Click here)
OK


18.REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver (Click here).


NEXT


19.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (if stored) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble codes.

  1. Read pending DTCs.

    OK:
    No pending DTC is output.

  1. Turn the ignition switch off.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
REPLACE ECM (Click here)
OK

END