Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2431    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1

DTC    P2432    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank1

DTC    P2433    Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank1

DTC    P2436    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank 2

DTC    P2437    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank 2

DTC    P2438    Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank 2

for Preparation Click here


DESCRIPTION

Refer to DTC P0412 .
Refer to DTC P0416 .

DTC No.
DTC Detection Condition
Trouble Area
P2431
P2436
Pressure sensor indicates a value below 45.63 kPa (342 mmHg), or higher than 135 kPa (1013 mmHg) (2 trip detection logic).
  1. Pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (bank 2))
  2. Open or short in pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (bank 2)) circuit
  3. ECM
P2432
P2437
While the engine is running, the voltage output of the pressure sensor is below 0.5 V (1 trip detection logic).
  1. Pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (bank 2))
  2. Open or short in pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (bank 2)) circuit
  3. ECM
P2433
P2438
While the engine is running, the voltage output of the pressure sensor is higher than 4.5 V (1 trip detection logic).
  1. Pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (bank 2))
  2. Open or short in pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (bank 2)) circuit
  3. ECM

MONITOR DESCRIPTION

A085160E22
The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the emission control valve set in the secondary air injection system. Using this pressure value, the ECM determines whether the secondary air injection system is malfunctioning or not.
If there is a defect in the sensor or the sensor circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the pressure sensor or circuit and stores a DTC.

MONITOR STRATEGY


Related DTCs
P2431: Air flow/Pressure sensor circuit rationality (bank 1)
P2432: Air flow/Pressure sensor circuit range check (Low voltage) (bank 1)
P2433: Air flow/Pressure sensor circuit range check (High voltage) (bank 1)
P2436: Air flow/Pressure sensor circuit rationality (bank 2)
P2437: Air flow/Pressure sensor circuit range check (Low voltage) (bank 2)
P2438: Air flow/Pressure sensor circuit range check (High voltage) (bank 2)
Required Sensors/Components (Main)
Pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (bank 2))
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
P2432, P2433, P2437, P2438: 0.5 seconds
P2431, P2436: 5 seconds
MIL Operation
P2432, P2433, P2437, P2438: Immediate
P2431, P2436: 2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P2431 and P2436 
Monitor runs whenever following DTCs not stored
P2432, P2433, P2437, P2438 (AIR pressure sensor - Low/High)
Starter
OFF
Battery voltage
8 V or higher
Ignition switch
ON
Secondary air injection system pressure sensor circuit fail
(P2432, P2433, P2437, P2438)
Not detected

P2432, P2433, P2437 and P2438 
Monitor runs whenever following DTCs not stored
None
Starter
OFF
Battery voltage
8 V or higher
Ignition switch
ON

TYPICAL MALFUNCTION THRESHOLDS


P2431 and P2436 
Secondary air injection pressure
Below 45.63 kPa (342 mmHg), or higher than 135 kPa (1013 mmHg)

P2432 and P2437 
Secondary air injection pressure sensor voltage
Below 0.5 V

P2433 and P2438 
Secondary air injection pressure sensor voltage
Higher than 4.5 V

COMPONENT OPERATING RANGE


P2431 and P2436 
Secondary air injection pressure
45.63 kPa (342 mmHg), or more, and 135 kPa (1013 mmHg) or less

P2432, P2433, P2437 and P2438 
Secondary air injection pressure sensor voltage
0.5 V or more, and 4.5 V or less

CONFIRMATION DRIVING PATTERN

NOTICE:
  1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
  2. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
  3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
  4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  1. Start the engine and warm it up.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the Techstream on.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
  10. Start the engine after the Techstream initialization is finished.
  11. Perform the System Check operation by pressing Next.
  12. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
  13. Enter the following menus: Powertrain / Engine and ECT / Trouble codes.
  14. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  15. After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  16. Input the DTC: P2431, P2432, P2433, P2436, P2437 or P2438.
  17. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  18. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If no permanent DTC is output, the system is normal.
    2. If a permanent DTC is output, the system is malfunctioning.

  19. Turn the ignition switch off.

WIRING DIAGRAM


A162276E10


INSPECTION PROCEDURE

HINT:
  1. Refer to "Data List / Active Test" [Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute)] (Click here).
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.

1.CHECK HARNESS AND CONNECTOR (EMISSION CONTROL VALVE SET - ECM)
  1. Disconnect the B61 and B62 emission control valve set connectors.

  1. Disconnect the B47, B48 and E78 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B61-3 (AIP) - E78-1 (AIP)
    Always
    Below 1 Ω
    B61-2 (VC) - B47-16 (VCV2)
    Always
    Below 1 Ω
    B61-4 (E2) - B48-7 (ETHA)
    Always
    Below 1 Ω
    B62-3 (AIP2) - E78-2 (AIP2)
    Always
    Below 1 Ω
    B62-2 (VC2) - B47-16 (VCV2)
    Always
    Below 1 Ω
    B62-4 (E22) - B48-7 (ETHA)
    Always
    Below 1 Ω
    B61-3 (AIP) or E78-1 (AIP) - Body ground
    Always
    10 kΩ or higher
    B61-2 (VC) or B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher
    B62-3 (AIP2) or E78-2 (AIP2) - Body ground
    Always
    10 kΩ or higher
    B62-2 (VC2) or B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK TERMINAL VOLTAGE (VC OF EMISSION CONTROL VALVE SET)
A219201E07
  1. Disconnect the emission control valve set connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B61-2 (VC) - B61-4 (E2)
    Ignition switch ON
    4.5 to 5.5 V
    B62-2 (VC2) - B62-4 (E22)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Emission Control Valve Set)
    *b
    for Bank 1
    *c
    for Bank 2



NG
REPLACE ECM (Click here)
OK


3.REPLACE EMISSION CONTROL VALVE SET
  1. Replace the emission control valve set.

    HINT:
    1. Replace the emission control valve set (Click here).
    2. Replace the No. 2 emission control valve set (Click here).


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for 30 seconds.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2431, P2432, P2433, P2436, P2437 or P2438.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    NORMAL
    (No DTC is output)
    A
    ABNORMAL
    (P2431, P2432, P2433, P2436, P2437 or P2438 is output)
    B



B
REPLACE ECM (Click here)
A

END