Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0420    Catalyst System Efficiency Below Threshold (Bank 1)

DTC    P0430    Catalyst System Efficiency Below Threshold (Bank 2)

for Preparation Click here


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.
The first sensor, the Air-Fuel Ratio (A/F) sensor, sends pre-catalyst information to the ECM. The second sensor, the Heated Oxygen (HO2) sensor, sends post-catalyst information to the ECM.
In order to detect any deterioration in the TWC, the ECM calculates the Oxygen Storage Capacity (OSC) of the TWC. This calculation is based on the voltage output of the HO2 sensor while performing active air-fuel ratio control.
The OSC value is an indication of the oxygen storage capacity of the TWC. When the vehicle is being driven with a warm engine, active air-fuel ratio control is performed for approximately 15 to 20 seconds.
When it is performed, the ECM deliberately sets the air-fuel ratio to lean or rich levels. If the rich-lean cycle of the HO2 sensor is long, the OSC becomes greater. There is a direct correlation between the OSCs of the HO2 sensor and the TWC.
The ECM uses the OSC value to determine the state of the TWC. If any deterioration has occurred, it illuminates the MIL and stores the DTC.
This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No.
DTC Detection Condition
Trouble Area
P0420
OSC value smaller than standard value under active air-fuel ratio control (1 trip detection logic)
  1. Gas leak from exhaust system
  2. A/F sensor (for bank 1 sensor 1)
  3. HO2 sensor (for bank 1 sensor 2)
  4. Exhaust manifold sub-assembly RH (TWC: Front catalyst) and front exhaust pipe assembly (TWC: Rear catalyst)
P0430
OSC value smaller than standard value under active air-fuel ratio control (1 trip detection logic)
  1. Gas leak from exhaust system
  2. A/F sensor (for bank 2 sensor 1)
  3. HO2 sensor (for bank 2 sensor 2)
  4. Exhaust manifold sub-assembly LH (TWC: Front catalyst) and front No. 2 exhaust pipe assembly (TWC: Rear catalyst)

CATALYST LOCATION


A287409E01


Text in Illustration 
*A
w/ Secondary Air Injection System
-
-
*1
Air Fuel Ratio Sensor (for Bank 1 Sensor 1)
*2
Air Fuel Ratio Sensor (for Bank 2 Sensor 1)
*3
Heated Oxygen Sensor (for Bank 1 Sensor 2)
*4
Heated Oxygen Sensor (for Bank 2 Sensor 2)
*5
TWC: Front Catalyst
*6
TWC: Rear Catalyst
*7
Exhaust Manifold Sub-assembly RH
*8
Exhaust Manifold Sub-assembly LH
*9
Front Exhaust Pipe Assembly
*10
Front No. 2 Exhaust Pipe Assembly
*11
Center Exhaust Pipe Assembly
*12
Tail Exhaust Pipe Assembly

NOTICE:
  1. When outputting DTC P0420 replace the exhaust manifold sub-assembly RH (*7) and the front exhaust pipe assembly (*9) together when catalyst replacement is necessary (Excluding air fuel ratio sensor *1 and heated oxygen sensor *3).
  2. When outputting DTC P0430 replace the exhaust manifold sub-assembly LH (*8) and the front No. 2 exhaust pipe assembly (*10) together when catalyst replacement is necessary (Excluding air fuel ratio sensor *2 and heated oxygen sensor *4).


A261516E02


Text in Illustration 
*A
w/o Secondary Air Injection System
-
-
*1
Air Fuel Ratio Sensor (for Bank 1 Sensor 1)
*2
Air Fuel Ratio Sensor (for Bank 2 Sensor 1)
*3
Heated Oxygen Sensor (for Bank 1 Sensor 2)
*4
Heated Oxygen Sensor (for Bank 2 Sensor 2)
*5
TWC: Front Catalyst
*6
TWC: Rear Catalyst
*7
Exhaust Manifold Sub-assembly RH
*8
Exhaust Manifold Sub-assembly LH
*9
Front Exhaust Pipe Assembly
*10
Front No. 2 Exhaust Pipe Assembly
*11
Center Exhaust Pipe Assembly
*12
Tail Exhaust Pipe Assembly

NOTICE:
  1. When outputting DTC P0420 replace the exhaust manifold sub-assembly RH (*7) and the front exhaust pipe assembly (*9) together when catalyst replacement is necessary (Excluding air fuel ratio sensor *1 and heated oxygen sensor *3).
  2. When outputting DTC P0430 replace the exhaust manifold sub-assembly LH (*8) and the front No. 2 exhaust pipe assembly (*10) together when catalyst replacement is necessary (Excluding air fuel ratio sensor *2 and heated oxygen sensor *4).


MONITOR STRATEGY


Related DTCs
P0420: Catalyst Deterioration (Bank 1)
P0430: Catalyst Deterioration (Bank 2)
Required Sensors/Components (Main)
Air fuel ratio sensor, Heated oxygen sensor
Required Sensors/Components (Related)
Intake air temperature sensor, Mass air flow meter, Crankshaft position sensor, Engine coolant temperature sensor
Frequency of Operation
Once per driving cycle
Duration
About 30 seconds
MIL Operation
1 driving cycle
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - advance)
P0012, P0022 (VVT system - retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - advance)
P0015, P0025 (Exhaust VVT system - retard)
P0016, P0018 (VVT system - misalignment)
P0017, P0019 (Exhaust VVT system - misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0037, P0038, P0057, P0058, P102D, P105D (Heated oxygen sensor heater)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120 - P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient engine coolant temperature for closed loop fuel control)
P0136 - P0139, P0156 - P0159, P0607 (Heated oxygen sensor)
P014C - P014F, P015A - P015D, P2195 - P2198, P2237 - P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0306 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351 - P0356 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0412, P0418, P1613 (Secondary air injection system control)
P0416, P0417, P2440 - P2445 (Secondary air injection system)
P0500 (Vehicle speed sensor)
P219A, P219B (Air-fuel ratio imbalance)
Response rate during fuel cut from rich condition
Completed
Battery voltage
11 V or more
IAT
-10°C (14°F) or more
ECT
75°C (167°F) or more
Atmospheric pressure
76 kPa(abs) [570 mmHg(abs)] or more
Idling
OFF
Engine speed
Less than 3200 rpm
A/F sensor status
Activated
Fuel system status
Closed loop
Engine load
10% or more, and less than 70%
All of the following conditions are met
Condition 1, 2 and 3
1. MAF
5 gm/sec or more, and less than 75 gm/sec
2. Front catalyst temperature (estimated)
690°C (1274°F) or more, and less than 860°C (1580°F)
3. Rear catalyst temperature (estimated)
500°C (932°F) or more, and less than 900°C (1652°F)
Shift position
4th or higher

TYPICAL MALFUNCTION THRESHOLDS


Oxygen Storage Capacity (OSC) of catalyst (Normalized)
Less than 1

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

HINT:
  1. It is necessary that the response of the heated oxygen sensor is normal in order to confirm DTCs P0420 and P0430. Therefore, perform the driving pattern for the heated oxygen sensor monitor before performing the drive pattern for the catalyst efficiency monitor.
  2. Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A283604E07

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the Techstream on.
  7. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.
  8. Check that Catalyst Efficiency / Current is Incomplete.
  9. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
  10. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Drive the vehicle while keeping the engine load as constant as possible.

  11. Drive the vehicle at 60 km/h (37 mph), and then decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  12. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / RL F/C B1S2, RL F/C B2S2 [D].
  13. Check the Test Value for RL F/C B1S2, RL F/C B2S2.
    1. If Test Value displays a value larger than 0, perform the following procedure, as the O2 sensor monitor is finished.

      HINT:
      If Test Value displays 0, perform step [C] until it displays a value larger than 0, as the O2 sensor monitor is not finished.

  14. Turn the ignition switch off and wait for at least 30 seconds [F].
  15. Turn the ignition switch to ON and turn the Techstream on.
  16. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [G].
  17. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [H].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. Drive the vehicle while keeping the engine load as constant as possible.
    2. The monitor item will change to Complete as the Catalyst Efficiency monitor operates.

  18. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [I].
  19. Check if any DTCs are stored.

    HINT:
    If the monitor item does not change to Complete, and no DTCs are stored, perform the following procedure.

  20. Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes or more [J].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. Drive the vehicle while keeping the engine load as constant as possible.
    2. The monitor item will change to Complete as the Catalyst Efficiency monitor operates.

  21. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [K].
  22. Check if any DTCs are stored.

    HINT:
    If the monitor item does not change to Complete, and no DTCs are stored, extend the driving time.

  23. If no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


CONDITIONING FOR SENSOR TESTING

HINT:
Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the A/F and HO2 sensors. This is in order to activate the sensors sufficiently to obtain the appropriate inspection results.


A118003E61

  1. (a) Connect the Techstream to the DLC3.
  2. (b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes.
  3. (c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.
  4. (d) While running the engine at 3000 rpm and 2000 rpm at 2 second intervals, check the waveforms of the A/F and HO2 sensors using the Techstream.

HINT:
  1. If either voltage output of the Air-Fuel Ratio (A/F) or Heated Oxygen (HO2) sensor does not fluctuate, or there is noise in the waveform of either sensor, the sensor may be malfunctioning.
  2. If the voltage outputs of both the sensors remain lean or rich, the air-fuel ratio may be extremely lean or rich. In such cases, perform the following Control the Injection Volume using the Techstream.
  3. If the Three-Way Catalytic Converter (TWC) has deteriorated, the HO2 sensor (located behind the TWC) voltage output fluctuates up and down frequently, even under normal driving conditions (active air-fuel ratio control is not performed).


A240224E01


INSPECTION PROCEDURE

HINT:
  1. If a malfunction cannot be found when troubleshooting DTC P0420 or P0430, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 or P0174 (System Too Lean) and P0172 or P0175 (System Too Rich).
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  5. Sensor 1 refers to the sensor closest to the engine assembly.
  6. Sensor 2 refers to the sensor farthest away from the engine assembly.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 AND/OR P0430)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0420 or P0430 is output
    A
    P0420 or P0430 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0420 or P0430 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the Techstream on.

  1. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

  1. Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the 12.5 or -12.5 button to change the fuel injection volume).

  1. Monitor the voltage outputs of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

    HINT:
    1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
    3. The A/F sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    4. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Techstream Display (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1 or AFS Voltage B2S1
    (A/F)
    12.5%
    Rich
    Less than 3.1 V
    AFS Voltage B1S1 or AFS Voltage B2S1
    (A/F)
    -12.5%
    Lean
    More than 3.4 V
    O2S B1S2 or O2S B2S2
    (HO2)
    12.5%
    Rich
    More than 0.55 V
    O2S B1S2 or O2S B2S2
    (HO2)
    -12.5%
    Lean
    Less than 0.4 V

    Result 
    Status AFS Voltage B1S1 or AFS Voltage B2S1
    Status O2S B1S2 or O2S B2S2
    A/F Condition and A/F and HO2 Sensor Condition
    Misfire
    Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    1. Three-Way Catalytic Converter (TWC)
    2. Gas leak from exhaust system
    A
    Lean
    Lean/Rich
    A/F sensor malfunction
    -
    A/F sensor
    B
    Rich
    Lean/Rich
    A/F sensor malfunction
    -
    A/F sensor
    Lean/Rich
    Lean
    HO2 sensor malfunction
    -
    1. HO2 sensor
    2. Gas leak from exhaust system
    C
    Lean/Rich
    Rich
    HO2 sensor malfunction
    -
    1. HO2 sensor
    2. Gas leak from exhaust system
    Lean
    Lean
    Actual air-fuel ratio lean
    May occur
    1. Extremely rich or lean actual air-fuel ratio
    2. Gas leak from exhaust system
    D
    Rich
    Rich
    Actual air-fuel ratio rich
    -
    1. Extremely rich or lean actual air-fuel ratio
    2. Gas leak from exhaust system
    Lean: During Control the Injection Volume for A/F Sensor, the A/F sensor output voltage (AFS) is consistently more than 3.4 V, and the HO2 sensor output voltage (O2S) is consistently less than 0.4 V.
    Rich: During Control the Injection Volume for A/F Sensor, the AFS is consistently less than 3.1 V, and the O2S is consistently more than 0.55 V.
    Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the A/F sensor and HO2 sensor alternates correctly.



B
Go to step 7

C
Go to step 5

D
Go to step 6
A


3.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
Go to step 8
OK


4.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)

NOTICE:
  1. When outputting DTC P0420 replace the exhaust manifold sub-assembly RH (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.
  2. When outputting DTC P0430 replace the exhaust manifold sub-assembly LH (TWC: Front catalyst) and the No. 2 front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.

HINT:
Confirm the replacement parts, referring to the illustration in the Catalyst Location.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0420 is output
    A, B
    P0430 is output
    C, D
    P0420 and P0430 are output
    A, B, C, D



A
REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: FRONT CATALYST) (Click here)

B
REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST) (Click here)

C
REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: FRONT CATALYST) (Click here)
D

REPLACE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST) (Click here)  

5.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



OK
Go to step 9

NG
Go to step 8

6.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



OK
Go to step 10

NG
Go to step 8

7.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NEXT
Go to step 11

8.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
  1. Repair or replace exhaust gas leak point.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here).



NEXT
Go to step 11

9.REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the heated oxygen sensor (Click here).



NEXT
Go to step 11

10.CHECK OF CAUSE EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
  1. Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure .


NEXT


11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read pending DTCs.

Result 
Result
Proceed to
DTC P0420 and/or P0430 is output
A
DTC is not output
B


B
END
A


12.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)

NOTICE:
  1. When outputting DTC P0420 replace the exhaust manifold sub-assembly RH (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.
  2. When outputting DTC P0430 replace the exhaust manifold sub-assembly LH (TWC: Front catalyst) and the No. 2 front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.

HINT:
Confirm the replacement parts, referring to the illustration in the Catalyst Location.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0420 is output
    A, B
    P0430 is output
    C, D
    P0420 and P0430 are output
    A, B, C, D



A
REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: FRONT CATALYST) (Click here)

B
REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST) (Click here)

C
REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: FRONT CATALYST) (Click here)
D

REPLACE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST) (Click here)