Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

TIRE PRESSURE WARNING SYSTEM > TEST MODE PROCEDURE

for Preparation Click here



TEST MODE (SIGNAL CHECK MODE) PROCEDURE

HINT:
  1. When entering test mode (signal check mode), the tire pressure warning ECU sets all the test mode (signal check mode) DTCs first.
    After the tire pressure warning ECU completes the signal check for each inspection item, the DTCs for systems that are determined to be normal will be cleared.
    The DTCs for other inspection items may not be cleared when only a certain signal is inspected.
  2. When test mode (signal check mode) returns to normal mode, all the test mode (signal check mode) DTCs will be cleared.
  3. Operation of the tire pressure warning reset switch can be checked in test mode (signal check mode).
  4. During test mode (signal check mode), the system is not initialized by pushing the tire pressure warning reset switch. The circuit of the tire pressure warning reset switch can be inspected during this mode.

  1. Turn the ignition switch off.

  2. Connect the Techstream to the DLC3.

  3. Turn the ignition switch to ON.

  4. Turn the Techstream on.



  5. Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.

    HINT:
    F100632E14
    Every time the test mode (signal check mode) DTC clear conditions are satisfied, the tire pressure warning light illuminated for 1 second. Following this, the tire pressure warning light blinks at 0.125 second intervals.

    Text in Illustration 
    *a
    0.125 seconds
    *b
    ON
    *c
    OFF

  6. Start the engine and allow it to run at 1000 rpm for 3 seconds or more to check the engine speed signal (C2194/94).

  7. Drive the vehicle at 20 km/h (12 mph) or more for 3 seconds or more to check the vehicle speed signal (C2191/91).

  8. Loosen the valve core and rapidly reduce the pressure (at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds) to check the transmitter data (C2181/81 to C2185/85).

    HINT:
    The transmitter ID is forcibly transmitted when the tire pressure is reduced rapidly.

  9. Check that the tire pressure warning system test mode DTCs are erased.

    Test Mode DTC
    Test Signal
    Test Mode DTC Clear Condition
    C2181/81 to C2185/85
    Transmitter Data
    Receive data from the transmitter which has a registered ID in the tire pressure warning ECU
    C2191/91
    Vehicle Speed Signal
    Vehicle speed of 20 km/h (12 mph) or more is detected for 3 seconds or more
    C2194/94
    Engine Speed Signal
    Engine speed of 1000 rpm or more is detected for 3 seconds or more

  10. Check the tire pressure warning reset switch.

    1. Press the tire pressure warning reset switch.

    2. Check the tire pressure warning light.

      Test Signal
      Normal Condition
      Tire Pressure Warning Reset Switch
      1. Switch on: Tire pressure warning light illuminates.
      2. Switch off: Tire pressure warning light blinks at 0.125 second intervals.

  11. Result

    HINT:
    After the signal check is completed, check for test mode (signal check mode) DTCs to confirm the system status.


    Condition
    Procedure
    Test mode (signal check mode) DTC is output
    Repair the faulty part and enter Signal Check again
    Test mode (signal check mode) DTCs are cleared
    No problem

  12. End of test mode (signal check mode)

    1. After completing the test mode (signal check mode), turn the ignition switch off and disconnect the Techstream.

  13. Test mode (signal check mode) DTCs

    1. If a trouble code is displayed during the test mode (signal check mode) DTC check, check the diagnosis procedure listed for that code. For details of each code, refer to See page below.

      DTC No.
      Detection Item
      See page
      C2181/81
      Transmitter ID1 not received
      Click here
      C2182/82
      Transmitter ID2 not received
      Click here
      C2183/83
      Transmitter ID3 not received
      Click here
      C2184/84
      Transmitter ID4 not received
      Click here
      C2185/85
      Transmitter ID5 not received
      Click here
      C2191/91
      Vehicle speed signal error
      Click here
      C2194/94
      Engine speed signal error
      Click here