Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

DTC    C2191/91    Vehicle Speed Signal Error (Test Mode DTC)

for Preparation Click here


DESCRIPTION

The tire pressure warning ECU receives a vehicle speed signal from the combination meter assembly. This DTC is stored upon entering test mode, and cleared when a vehicle speed signal of 20 km/h (12 mph) is detected for 3 seconds or more. This DTC is output only in test mode.

DTC No.
DTC Detection Condition
Trouble Area
C2191/91
Vehicle speed signal circuit malfunction
  1. Combination meter assembly
  2. Vehicle speed sensor
  3. Harness or connector
  4. Tire pressure warning ECU

WIRING DIAGRAM


C243848E03


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the tire pressure warning ECU, read the transmitter IDs stored in the old ECU using a Techstream and write them down before removal.
  2. It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the tire pressure warning ECU after the ECU has been replaced.

1.READ VALUE USING TECHSTREAM (VEHICLE SPEED)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check that the values indicated on the Techstream and on the combination meter assembly are the same.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    min.: 0 km/h (0 mph)
    max.: 255 km/h (158 mph)
    Actual vehicle speed
    Speed indicated on the combination meter assembly

    OK:
    Vehicle speed indicated on the tester and on the combination meter assembly are the same.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.INSPECT TIRE PRESSURE WARNING ECU (SPD SIGNAL)


    C162301E53
  1. Disconnect the E74 tire pressure warning ECU connector.

  1. Jack up the vehicle.

  1. Move the shift lever to N.

  1. Turn the ignition switch to ON.

  1. Check the waveform of the tire pressure warning ECU connector using an oscilloscope, while turning the wheel slowly.

    OK:
    Tester Connection
    Switch Condition
    Specified Condition
    E74-2 (SPD) - E74-9 (GND)
    Ignition switch ON
    Correct waveform is as shown

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Tire Pressure Warning ECU)
    Tool Setting 
    Item
    Contents
    Terminal No. (Symbols)
    E74-2 (SPD) - E74-9 (GND)
    Tool Setting
    5 V/DIV., 200 ms/DIV.
    Vehicle Condition
    Driving wheels rotating slowly

    HINT:
    The wavelength becomes shorter as the vehicle speed increases.



NG
Go to step 3
OK

REPLACE TIRE PRESSURE WARNING ECU (Click here)  

3.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU - COMBINATION METER ASSEMBLY)
  1. Disconnect the E74 tire pressure warning ECU connector.

  1. Disconnect the E13 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E74-2 (SPD) - E13-14 (+S)
    Always
    Below 1 Ω
    E74-2 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)