Home › BODY ELECTRICAL › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM

WIRELESS DOOR LOCK CONTROL SYSTEM > Only Wireless Control Function is Inoperative

for Preparation Click here


DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU.

WIRING DIAGRAM


B175113E01


INSPECTION PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

OK:
Each function of wireless door lock control system operates normally using transmitter switches (Click here).



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.REPLACE TRANSMITTER BATTERY
  1. After replacing the transmitter battery, check that the doors can be locked and unlocked using the transmitter switches (Click here).

    OK:
    Doors can be locked and unlocked with transmitter.



NG
Go to step 3
OK

END (TRANSMITTER BATTERY DEFECTIVE) 

3.SWITCH TO SELF DIAGNOSTIC MODE
  1. Switch to self-diagnostic mode by operating the ignition key cylinder.

    1. Make sure the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.

    2. Within 5 seconds of removing the key, insert the key into the ignition key cylinder (ignition switch OFF). Then turn the ignition switch ON and OFF.

    3. Within 30 seconds of turning the ignition switch OFF, perform the following operation 9 times: turn the ignition switch ON and OFF.

      NOTICE:
      If the system cannot enter self-diagnostic mode, the system returns to normal mode.

      HINT:
      1. Turning the ignition switch ON after the above operations have been completed ends self-diagnostic mode.
      2. Do not lock or unlock doors during self-diagnostic mode.



    B110075E18
  1. Check that the system has switched to self-diagnostic mode by checking the wireless door lock buzzer sound.

    OK:
    Buzzer pattern is same as illustration on left.



NG
Go to step 8
OK


4.CHECK BY SELF DIAGNOSTIC MODE


  1. Check the diagnostic outputs when the door control transmitter switch is held down. The diagnostic outputs can be checked by the wireless door lock buzzer sound.


    B133371E01


    Result:

    Result
    Proceed to
    Unmatching recognition code is output
    A
    Normal waves (buzzer patterns) for LOCK and UNLOCK switches are output
    B
    No diagnosis outputs
    C



B
END (TRANSMITTER BATTERY DEFECTIVE)

C
Go to step 6
A


5.REGISTER RECOGNITION CODE
  1. Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

    OK:
    Recognition code can be registered.



NG
Go to step 12
OK

END 

6.CHECK RESPONSE OF DOOR CONTROL RECEIVER
  1. When a new or normally functioning door lock control transmitter switch for the same vehicle type is held down, check that an unmatching recognition code is output.

    OK:
    Unmatching recognition code is output.



NG
Go to step 7
OK

REPLACE DOOR CONTROL TRANSMITTER MODULE (Click here)  

7.REPLACE DOOR CONTROL RECEIVER
  1. After replacing the door control receiver, check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.

    OK:
    Doors can be locked and unlocked with transmitter.



NG
REPLACE DOOR CONTROL TRANSMITTER MODULE (Click here)
OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE) 

8.PERFORM ACTIVE TEST USING TECHSTREAM (WIRELESS BUZZER)
  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. According to the display on tester, perform the "Active Test".


Main body: 
Tester Display
Test Part
Control Range
Diagnostic Note
Wireless Buzzer
Sounds wireless buzzer
ON or OFF
-

OK:
Wireless buzzer turns ON/OFF.



NG
Go to step 13
OK


9.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
  1. Remove the unlock warning switch.



    B062710E01
  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Not pushed
    10 kΩ or higher
    Pushed
    Below 1 Ω



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU)


    B062225E01
  1. Disconnect the E7 main body ECU connector.

  1. Disconnect the E23 door control receiver connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    E7-4 (RDA) - E23-2 (RDA)
    Below 1 Ω
    E7-4 (RDA) or E23-2 (RDA) - Body ground
    10 kΩ or higher
    E7-3 (PRG) - E23-3 (PRG)
    Below 1 Ω
    E7-3 (PRG) or E23-3 (PRG) - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the door control receiver connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK DOOR CONTROL RECEIVER (OUTPUT)


    B051174E02
  1. Measure the voltage of the connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E23-2 (RDA) - Body ground
    Ignition switch off, all doors closed and transmitter switch not pressed
    11 to 14 V
    Ignition switch off, all doors closed and transmitter switch pressed
    Pulse generation



NG
Go to step 12
OK

REPLACE MAIN BODY ECU 

12.REPLACE DOOR CONTROL TRANSMITTER MODULE
  1. Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.

    OK:
    Doors can be locked and unlocked with transmitter.



NG
REPLACE DOOR CONTROL RECEIVER
OK

END (DOOR CONTROL TRANSMITTER MODULE DEFECTIVE) 

13.INSPECT WIRELESS DOOR LOCK BUZZER
B030785E03
  1. Disconnect the A12 wireless door lock buzzer connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    Approximately 1 kΩ

  1. Reconnect wireless door lock buzzer connector.



NG
REPLACE WIRELESS DOOR LOCK BUZZER (Click here)
OK


14.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU)
B062227E01
  1. Disconnect the A12 wireless door lock buzzer connector.

  1. Disconnect the 1B main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    1B-10 (BZR) - A12-1
    Below 1 Ω
    1B-6 (BZR2) - A12-2
    Below 1 Ω
    1B-10 (BZR) or A12-1 - Body ground
    10 kΩ or higher
    1B-6 (BZR2) or A12-2 - Body ground
    10 kΩ or higher

  1. Reconnect the A12 wireless door lock buzzer connector.

  1. Reconnect the 1B main body ECU connector.



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU