AUDIO AND VISUAL SYSTEM > Illumination Circuit |

| 1.CHECK ILLUMINATION |
Check if the illumination for the multi-display, steering pad switch, glove box light, cigarette lighter, or others (seat heater switch, front seat memory switch, etc.) comes on when the light control switch is turned to the head or tail position.
| Result | Proceed to |
| Illumination comes on for all components except steering pad switch. | A |
| Illumination comes on for all components except radio receiver. | B |
| No illumination comes on for radio receiver, back sonar switch, hazard switch, cigarette lighter, etc. | C |
| Illumination comes on for all components except steering pad switch and radio receiver assembly. | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (TAIL RELAY - SPIRAL CABLE) |
![]() |
Disconnect the E17 spiral cable connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E17-1 (ILL+) - Body ground | Light control switch head or tail | 11 to 14 V |
| *a | Front view of wire harness connector (to Spiral Cable) |
|
| ||||
| OK | |
| 3.INSPECT STEERING PAD SWITCH ASSEMBLY (STEERING PAD SIDE) |

Disconnect the steering pad switch connector.
Apply battery voltage to the terminals of the connector, and check the LED illumination condition.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 1 (ILL+) Battery negative (-) → Terminal 10 (EAU) | Light illuminates |
|
| ||||
| OK | |
| 4.INSPECT SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Remove the spiral cable (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A-1 (ILL+) - B-1 (ILL+) | Spiral cable is turned 2.5 rotations counterclockwise | Below 1 Ω |
| Spiral cable is centered | ||
| Spiral cable is turned 2.5 rotations clockwise | ||
| A-10 (EAU) - B-10 (EAU) | Spiral cable is turned 2.5 rotations counterclockwise | Below 1 Ω |
| Spiral cable is centered | ||
| Spiral cable is turned 2.5 rotations clockwise |
| *a | Vehicle Side |
| *b | Steering Pad Switch Side |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER) |
Disconnect the E17 spiral cable connector.
Disconnect the E43 radio receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E43-6 (SWG) - E17-10 (EAU) | Always | Below 1 Ω |
| E43-6 (SWG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - TAIL RELAY) |
![]() |
Disconnect the E83*1 or E41*2 receiver connector.
*1: for 10 Speaker with Sub-woofer
*2: for 6 Speaker
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E83-2 (ILL+) - Body ground | Light control switch head or tail | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| E41-10 (ILL+) - Body ground | Light control switch head or tail | 11 to 14 V |
| *a | Front view of wire harness connector (to Radio Receiver Assembly (for 10 Speaker with Sub-woofer)) |
| *b | Front view of wire harness connector (to Radio Receiver Assembly (for 6 Speaker)) |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BODY GROUND) |
![]() |
Disconnect the E83*1 or E42*2 receiver connector.
*1: for 10 Speaker with Sub-woofer
*2: for 6 Speaker
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E83-12 (ILL-) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| E42-5 (ILL-) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Radio Receiver Assembly (for 10 Speaker with Sub-woofer)) |
| *b | Front view of wire harness connector (to Radio Receiver Assembly (for 6 Speaker)) |
|
| ||||
| OK | ||
| ||