Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Illumination Circuit

for Preparation Click here


DESCRIPTION

  1. Upon receiving signals from the switches, the main body ECU illuminates the lights.

WIRING DIAGRAM


E260848E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM (ILLUMINATED ENTRY SYSTEM)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Turn the room lights switch to the DOOR position.

  1. Make sure all doors are closed (courtesy light switches OFF).

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Normal Condition
    Illuminated Entry System
    Transponder key amplifier (Ignition key cylinder light)
    Room light and rear room light (Room lights switch is in DOOR position and all doors are closed)
    OFF/ON
    -

    OK:
    The illuminated entry system operates normally when operating it through the Techstream.

Result 
Result
Proceed to
OK
A
NG (Transponder key amplifier (ignition key cylinder light) does not come on)
B
NG (Room light assembly does not come on)
C
NG (Rear Room light assembly does not come on)
D


B
Go to step 2

C
Go to step 5

D
Go to step 8
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT TRANSPONDER KEY AMPLIFIER (IGNITION KEY CYLINDER LIGHT)
  1. Inspect the transponder key amplifier (Click here).



NG
REPLACE TRANSPONDER KEY AMPLIFIER (IGNITION KEY CYLINDER LIGHT) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - DOME RELAY)


    E214732E01
  1. Disconnect the transponder key amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E72-2 (ILL+) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Transponder Key Amplifier)

  1. Reconnect the transponder key amplifier connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - MAIN BODY ECU)
  1. Disconnect the E72 transponder key amplifier connector.

  1. Disconnect the 1K main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E72-6 (ILL-) - 1K-9
    Always
    Below 1 Ω
    E72-6 (ILL-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the transponder key amplifier connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

5.INSPECT ROOM LIGHT ASSEMBLY
  1. Inspect the room light assembly (Click here).



NG
REPLACE ROOM LIGHT ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (ROOM LIGHT ASSEMBLY - DOME RELAY)


    E214733E01
  1. Disconnect the room light assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    R2-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Room Light Assembly)

  1. Reconnect the room light assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (ROOM LIGHT ASSEMBLY - MAIN BODY ECU)
  1. Disconnect the R2 room light assembly connector.

  1. Disconnect the 1A main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R2-2 - 1A-8
    Always
    Below 1 Ω
    R2-2 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the room light assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

8.INSPECT REAR ROOM LIGHT ASSEMBLY
  1. Inspect the rear room light assembly (Click here).



NG
REPLACE REAR ROOM LIGHT ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (REAR ROOM LIGHT ASSEMBLY - DOME RELAY)


    E214733E02
  1. Disconnect the rear room light assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    R3-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Room Light Assembly)

  1. Reconnect the rear room light assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK HARNESS AND CONNECTOR (REAR ROOM LIGHT ASSEMBLY - MAIN BODY ECU)
  1. Disconnect the R3 rear room light assembly connector.

  1. Disconnect the 1A main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R3-2 - 1A-8
    Always
    Below 1 Ω
    R3-2 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the rear room light assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU