DTC P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit |
DTC P0121 Throttle Pedal Position Sensor / Switch "A" Circuit Range / Performance |
DTC P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input |
DTC P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |
DTC P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit |
DTC P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input |
DTC P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input |
DTC P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0120 | The output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic) |
|
| P0121 | The difference between VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds or less (1 trip detection logic) |
|
| P0122 | The output voltage of VTA1 is 0.2 V or less for 2 seconds or more (1 trip detection logic) |
|
| P0123 | The output voltage of VTA1 is 4.535 V or more for 2 seconds or more (1 trip detection logic) |
|
| P0220 | The output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic) |
|
| P0222 | The output voltage of VTA2 is 1.75 V or less for 2 seconds or more (1 trip detection logic) |
|
| P0223 | The output voltage of VTA2 is 4.8 V or more, and VTA1 is between 0.2 V and 2.02 V for 2 seconds or more (1 trip detection logic) |
|
| P2135 | Either condition (a) or (b) is met (1 trip detection logic):
|
|
| Techstream Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed |
| Throttle Position No. 1 | 0.5 to 1.1 V | 3.2 to 4.8 V |
| Throttle Position No. 2 | 2.1 to 3.1 V | 4.6 to 4.98 V |
| Related DTCs | P0120: Throttle position sensor 1 range check (Fluctuating) P0121: Throttle position sensor rationality P0122: Throttle position sensor 1 range check (Low voltage) P0123: Throttle position sensor 1 range check (High voltage) P0220: Throttle position sensor 2 range check (Fluctuating) P0222: Throttle position sensor 2 range check (Low voltage) P0223: Throttle position sensor 2 range check (High voltage) P2135: Throttle position sensor range check (Correlation) |
| Required Sensors/Components (Main) | Throttle position sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 2 seconds: P0120, P0122, P0123, P0220, P0222 and P0223 Within 2 seconds: P0121 0.5 seconds: P2135 Case 1 0.4 seconds: P2135 Case 2 |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Either of following conditions A or B met | - |
| A. Time after ignition switch OFF to ON | 0.012 seconds or more |
| B. Command to electronic throttle actuator power | ON |
| Either of following conditions A or B met | - |
| A. Ignition switch | ON |
| B. Electronic throttle motor power | ON |
| TP sensor malfunction (P0120, P0122, P0123, P0220, P0222, P0223, P2135) | Not detected |
| VTA1 voltage | 0.2 V or less, or 4.535 V or more |
| Either of following conditions is met | - |
| Difference of learned TP sensor opener position voltage between VTA2 and VTA1 | More than 1.6 V |
| Difference of learned TP sensor opener position voltage between VTA2 and VTA1 | Less than 0.8 V |
| VTA1 voltage | 0.2 V or less |
| VTA1 voltage | 4.535 V or more |
| Either of following conditions is met: | Condition A or B |
| A. VTA2 voltage | 1.75 V or less |
| B. VTA2 voltage when VTA1 0.2 V or more, and 2.02 V or less | 4.8 V or more |
| VTA2 voltage | 1.75 V or less |
| VTA2 voltage when VTA1 0.2 V or more, and 2.02 V or less | 4.8 V or more |
| Difference between VTA1 and VTA2 voltages | 0.02 V or less |
| VTA1 voltage | 0.2 V or less |
| VTA2 voltage | 1.75 V or less |
| All of the following conditions are met | - |
| VTA1 voltage | More than 0.2 V, and less than 4.535 V |
| VTA2 voltage | More than 1.75 V, and less than 4.8 V |
| Difference between VTA1 and VTA2 voltage | More than 0.02 V |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING TECHSTREAM (THROTTLE POSITION SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.
Read the values displayed on the Techstream.
| When Accelerator Pedal Released | When Accelerator Pedal Depressed | Trouble Area | Proceed to | ||
| Throttle Position No. 1 | Throttle Position No. 2 | Throttle Position No. 1 | Throttle Position No. 2 | ||
| 0 V to 0.2 V | 0 V to 0.2 V | 0 V to 0.2 V | 0 V to 0.2 V | VC circuit open | A |
| 4.5 V to 4.98 V | 4.5 V to 4.98 V | 4.5 V to 4.98 V | 4.5 V to 4.98 V | E2 circuit open | |
| 0 V to 0.2 V, or 4.5 V to 4.98 V | 2.1 V to 3.1 V (Fail-safe) | 0 V to 0.2 V, or 4.5 V to 4.98 V | 2.1 V to 3.1 V (Fail-safe) | VTA1 circuit open or ground short | |
| 0.6 V to 1.4 V (Fail-safe) | 0 V to 0.2 V, or 4.5 V to 4.98 V | 0.6 V to 1.4 V (Fail-safe) | 0 V to 0.2 V, or 4.5 V to 4.98 V | VTA2 circuit open or ground short | |
| 0.5 V to 1.1 V | 2.1 V to 3.1 V | 3.2 V to 4.8 V (Not fail-safe) | 4.6 V to 4.98 V (Not fail-safe) | Throttle position sensor circuit normal | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
Disconnect the B14 throttle with motor body assembly connector.
Disconnect the B49 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B14-5 (VC) - B49-13 (VCTA) | Always | Below 1 Ω |
| B14-6 (VTA) - B49-15 (VTA1) | Always | Below 1 Ω |
| B14-4 (VTA2) - B49-16 (VTA2) | Always | Below 1 Ω |
| B14-3 (E2) - B49-14 (ETA) | Always | Below 1 Ω |
| B14-5 (VC) or B49-13 (VCTA) - Body ground | Always | 10 kΩ or higher |
| B14-6 (VTA) or B49-15 (VTA1) - Body ground | Always | 10 kΩ or higher |
| B14-4 (VTA2) or B49-16 (VTA2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT ECM (VC VOLTAGE) |
![]() |
Disconnect the throttle with motor body assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B14-5 (VC) - B14-3 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Throttle with Motor Body Assembly) |
|
| ||||
| OK | |
| 4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY |
Replace throttle with motor body assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (Click here).
Start the engine.
Refer to the confirmation driving pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 is output | A |
| No output | B |
|
| ||||
| A | ||
| ||