Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0705    Transmission Range Sensor Circuit Malfunction (PRNDL Input)

for Preparation Click here


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.

DTC No.
DTC Detection Conditions
Trouble Areas
P0705
When one of following conditions is met:
  1. Open or short in park/neutral position switch circuit
  2. Shift lock control unit assembly (Shift lock control ECU)
  3. Park/neutral position switch
  4. ECM
(A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic).
  1. One of the following conditions is met.
    P position signal is ON.
    N position signal is ON.
    NSW input signal is ON.
  2. R position signal is ON.
  3. D position signal is ON.
  4. 3 position signal is ON.
  5. 2 position signal is ON.
(B) All of the following conditions are met simultaneously (2-trip detection logic).
  1. P position signal is OFF.
  2. N position signal is OFF.
  3. NSW input signal is OFF.
  4. R position signal is OFF.
  5. D position signal is OFF.
  6. 3 position signal is OFF.
  7. 2 position signal is OFF.
(C) When any of following conditions is met, the 4 or L position signal is ON for 2.0 seconds or more (2-trip detection logic).
  1. P position signal is ON.
  2. N position signal is ON.
  3. NSW input signal is ON.
  4. R position signal is ON.
  5. 3 position signal is ON.

MONITOR DESCRIPTION

The DTC indicates a problem with the park/neutral position switch or the wire harness in the park/neutral position switch circuit.
For safety, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
When the park/neutral position switch sends more than one signal at a time from switch positions P, R, N, D, 3 or 2, the ECM interprets this as a fault in the switch. The ECM will turn on the MIL and store the DTC.

MONITOR STRATEGY


Related DTCs
P0705: Park/neutral position switch/Verify switch input
Required sensors/Components
Park/neutral position switch
Frequency of operation
Continuous
Duration
Conditions (A) and (C):
2 seconds
Condition (B):
60 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present.
None
Ignition switch
ON
Battery voltage
10.5 V or more

TYPICAL MALFUNCTION THRESHOLDS

One of the following conditions is met: Condition (A), (B) or (C)

When 2 or more of the following signals are input at the same time
Condition (A) 
One of the following conditions is met:
P switch
N switch
NSW switch
ON
R switch
ON
D switch
ON
3 switch
ON
2 switch
ON

All of following conditions are met
Condition (B) 
P switch
OFF
N switch
OFF
NSW switch
OFF
R switch
OFF
D switch
OFF
3 switch
OFF
2 switch
OFF

When any of following conditions is met, the 4 or L position signal is ON
Condition (C) 
P switch
ON
N switch
ON
NSW switch
ON
R switch
ON
3 switch
ON

COMPONENT OPERATING RANGE


Park/neutral position switch
The park/neutral position switch sends only one signal to the ECM

WIRING DIAGRAM


C259490E01


INSPECTION PROCEDURE

NOTICE:
  1. Perform the universal trip to clear permanent DTCs (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Turn the ignition switch off.
  2. Connect the Techstream to the DLC3.
  3. Turn the ignition switch to ON.
  4. Turn the Techstream on.
  5. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
  6. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in P and N
    2. ON: Shift lever in P or N
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW Status (P Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in P
    2. ON: Shift lever in P
    Shift SW Status (R Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in R
    2. ON: Shift lever in R
    Shift SW Status (2 Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in 2 and L
    2. ON: Shift lever in 2 or L
    Shift SW Status (L Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in L
    2. ON: Shift lever in L
    Shift SW Status (N Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in N
    2. ON: Shift lever in N
    Shift SW Status (D Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in D
    2. ON: Shift lever in D
    Shift SW Status (4 Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in D and 4
    2. ON: Shift lever in D or 4
    Shift SW Status (3 Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in 3
    2. ON: Shift lever in 3
1.CHECK HARNESS AND CONNECTOR (IG1 FUSE - PARK/NEUTRAL POSITION SWITCH)


    C259502E03
  1. Disconnect the connector from the park/neutral position switch.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B35-2 (RB) - Body ground
Ignition switch ON
11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Park/Neutral Position Switch)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)
C259502E01
  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B35-4 (B) - Body ground
Ignition switch ON
11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Park/Neutral Position Switch)


NG
Go to step 7
OK


3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C193931E41
  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
4 (B) - 5 (L)
Shift lever in P or N
Below 1 Ω
Shift lever not in P and N
10 kΩ or higher
2 (RB) - 6 (PL)
Shift lever in P
Below 1 Ω
Shift lever not in P
10 kΩ or higher
1 (RL) - 2 (RB)
Shift lever in R
Below 1 Ω
Shift lever not in R
10 kΩ or higher
2 (RB) - 9 (NL)
Shift lever in N
Below 1 Ω
Shift lever not in N
10 kΩ or higher
2 (RB) - 7 (DL)
Shift lever in D or 4
Below 1 Ω
Shift lever not in D and 4
10 kΩ or higher
2 (RB) - 3 (2L)
Shift lever in 3
Below 1 Ω
Shift lever not in 3
10 kΩ or higher
2 (RB) - 8 (LL)
Shift lever in 2 or L
Below 1 Ω
Shift lever not in 2 and L
10 kΩ or higher

Text in Illustration 
*a
Component without harness connected
(Park/Neutral Position Switch)


NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (SHIFT LOCK CONTROL ECU)


    C189651E06
  1. Connect the B35 park/neutral position switch connector.

  1. Disconnect the E28 connector from the shift lock control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    9 (NSSD) - 2 (MTD)
    Shift lever in D
    Below 1 Ω
    Shift lever in 4
    10 kΩ or higher
    9 (NSSD) - 3 (MT4)
    Shift lever in D
    10 kΩ or higher
    Shift lever in 4
    Below 1 Ω
    10 (NSSL) - 5 (MT2)
    Shift lever in 2
    Below 1 Ω
    Shift lever in L
    10 kΩ or higher
    10 (NSSL) - 4 (MTL)
    Shift lever in 2
    10 kΩ or higher
    Shift lever in L
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Shift lock control ECU (Transmission Control Switch)



NG
REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - SHIFT LOCK CONTROL ECU)
C189669E06
  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E28-9 (NSSD) - Body ground
  1. Ignition switch ON
  2. Shift lever in D
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in D
Below 1 V
E28-10 (NSSL) - Body ground
  1. Ignition switch ON
  2. Shift lever in 2
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in 2
Below 1 V

Text in Illustration 
*a
Front view of wire harness connector
(to Shift lock control ECU (Transmission Control Switch)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)


    C259485E03
  1. Connect the E28 shift lock control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B47-23 (3)*2 - B49-12 (E1)
    1. Ignition switch ON
    2. Shift lever in 3
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in 3
    Below 1 V
    B47-24 (2)*2 - B49-12 (E1)
    1. Ignition switch ON
    2. Shift lever in 2 or L
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in 2 and L
    Below 1 V
    B47-27 (D) - B49-12 (E1)
    1. Ignition switch ON
    2. Shift lever in D or 4
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in D and 4
    Below 1 V
    B47-28 (R) - B49-12 (E1)
    1. Ignition switch ON
    2. Shift lever in R
    11 to 14 V*1
    1. Ignition switch ON
    2. Shift lever not in R
    Below 1 V
    B47-29 (N) - B49-12 (E1)
    1. Ignition switch ON
    2. Shift lever in N
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in N
    Below 1 V
    B47-35 (P) - B49-12 (E1)
    1. Ignition switch ON
    2. Shift lever in P
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in P
    Below 1 V
    E77-23 (L) - B49-12 (E1)
    1. Ignition switch ON
    2. Shift lever in L
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in L
    Below 1 V
    E77-24 (4) - B49-12 (E1)
    1. Ignition switch ON
    2. Shift lever in 4
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in 4
    Below 1 V
    E78-14 (2)*3 - B49-12 (E1)
    1. Ignition switch ON
    2. Shift lever in 2 or L
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in 2 and L
    Below 1 V
    E78-19 (3)*3 - B49-12 (E1)
    1. Ignition switch ON
    2. Shift lever in 3
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in 3
    Below 1 V

    HINT:
    *1: The voltage will drop slightly due to illumination of the back up light.
    *2: w/o Secondary Air Injection System
    *3: w/ Secondary Air Injection System

    Text in Illustration 
    *A
    w/o Secondary Air Injection System
    *B
    w/ Secondary Air Injection System
    *a
    Component with harness connected
    (ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
  1. Turn the ignition switch off.

  1. Disconnect the B48 connector from the ECM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B48-2 (NSW) - B35-4 (B)
    Always
    Below 1 Ω
    B35-4 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)