Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1268    Transfer L4 Position Switch Circuit

DTC    C1283    L4 Position Switch

for Preparation Click here


DESCRIPTION

A-TRAC is activated if wheel skid is detected while the transfer is in the L4(for automatic transmission) or LL(for manual transmission) position.

DTC Code
DTC Detection Condition
Trouble Area
C1268*1
  1. Open circuit detected between the Skid Control ECU and ECM terminals and between the Skid Control ECU and 4WD ECU terminals (between EXI and L4 and between EXI and 4WD).*3
  2. Open circuit detected between the Skid Control ECU and ECM terminals (between EXI and L4).*4
  3. Open circuit detected between the Skid Control ECU and 4WD ECU terminals (between EXI and 4WD).*5
  4. Open circuit detected between the Skid Control ECU (NEO) and GND terminals.
  1. ECM
  2. Four wheel drive control ECU
  3. Master cylinder solenoid (Skid Control ECU)
  4. Harness or connector
C1268*2
Short circuit detected between the Skid Control ECU (NEO) and GND terminals.
  1. Master cylinder solenoid (Skid Control ECU)
  2. Harness or connector
C1283
Detected only during test mode
  1. ECM
  2. Four wheel drive control ECU
  3. Master cylinder solenoid (Skid Control ECU)
  4. Harness or connector
  1. *1: for 4WD
  2. *2: for 2WD
  3. *3: w/ Rear Differential Lock
  4. *4: w/o Rear Differential Lock
  5. *5: for Manual Transmission

WIRING DIAGRAM


C218838E05


C230322E03


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

HINT:
The Skid Control ECU uses the NEO terminal to determine whether the vehicle is 2WD or 4WD.

1.CHECK VEHICLE EQUIPMENT
  1. Confirm whether the vehicle is 2WD or 4WD.
    Result 
    Result
    Proceed to
    for 2WD
    A
    for 4WD
    B



B
Go to step 4
A


2.CHECK CONNECTOR CONNECTION CONDITION
  1. Disconnect the A4 skid control ECU connector.

  1. Confirm that the connector's contacts are not contaminated by foreign substances or water seepage.

OK:
Connector's contacts are not contaminated by foreign substances or water seepage.



NG
CLEAN CONNECTOR
OK


3.INSPECT SKID CONTROL ECU (NEO TERMINAL)


    C213546E12
  1. Disconnect the A4 skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-43 (NEO) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)  

4.INSPECT SKID CONTROL ECU (NEO TERMINAL)


    C213546E12
  1. Disconnect the A4 skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-43 (NEO) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT SKID CONTROL ECU (EXI TERMINAL VOLTAGE)


  1. for Automatic Transmission



      C213546E13
    1. Disconnect the A4 skid control ECU connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Transfer Condition
      Specified Condition
      A4-27 (EXI) - Body ground
      L4
      Below 1.5 V
      A4-27 (EXI) - Body ground
      Other than above
      8 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Skid Control ECU)



  1. for Manual Transmission



      C213546E13
    1. Disconnect the A4 skid control ECU connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Transfer Condition
      Specified Condition
      A4-27 (EXI) - Body ground
      LL
      Below 1.5 V
      A4-27 (EXI) - Body ground
      Other than above
      8 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Skid Control ECU)
      Result 
      Result
      Proceed to
      OK
      A
      NG (for Automatic Transmission w/ Rear Diff Lock)
      B
      NG (for Automatic Transmission w/o Rear Diff Lock)
      C
      NG (for Manual Transmission w/ Rear Diff Lock)
      D



B
Go to step 7

C
Go to step 8

D
Go to step 9
A


6.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)  

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ECM, 4WD CONTROL ECU (REAR DIFF LOCK))
  1. Disconnect the A4 skid control ECU connector.

  1. Disconnect the transfer indicator switch (for L4 position) connector.

  1. Disconnect the ECM connector.

  1. Disconnect the four wheel drive control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-27 (EXI) - E78-16 (L4)
    Always
    Below 1 Ω
    A4-27 (EXI) - L7-8 (4WD)
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 10
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ECM)
  1. Disconnect the A4 skid control ECU connector.

  1. Disconnect the transfer indicator switch (for L4 position) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-27 (EXI) - E78-16 (L4)
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 11
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4WD CONTROL ECU (REAR DIFF LOCK))
  1. Disconnect the A4 skid control ECU connector.

  1. Disconnect the transfer indicator switch (for LL position) connector.

  1. Disconnect the four wheel drive control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-27 (EXI) - L7-8 (4WD)
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 10
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

10.REPLACE 4 WHEEL DRIVE CONTROL ECU NO.2
  1. Replace the four wheel drive control ECU.

  1. Clear the DTCs.

  1. Turn the ignition switch off.

  1. Check if the same DTC is output.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
Go to step 11
A

END 

11.REPLACE ECM
  1. Replace the ECM (Click here).

  1. Clear the DTCs.

  1. Turn the ignition switch off.

  1. Check if the same DTC is output.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

END