Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > Only Back Door LOCK / UNLOCK Functions do not Operate

for Preparation Click here


DESCRIPTION

The back door ECU receives lock/unlock signals and activates the door lock motor accordingly.

WIRING DIAGRAM


B175118E02


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Enter the following menus: Body Electrical / Back Door / Active Test.

  1. According to the display on tester, perform the "Active Test".


Back door: 
Tester Display
Test Part
Control Range
Diagnostic Note
Door Lock
Operate back door lock motor
LOCK/UNLOCK
-

Result:
Result
Proceed to
Back door lock function cannot be operated
A
Back door lock function can be operated
B



B
Go to step 3
A


2.CHECK DTC OUTPUT (MULTIPLEX COMMUNICATION SYSTEM)
  1. Use a Techstream to check DTC output (Click here).

Result:
Result
Proceed to
DTC is output
A
DTC is not output
B



B
Go to step 5
A

GO TO DTC CHART (Click here)  

3.INSPECT BACK DOOR LOCK CYLINDER
B138201E02
  1. Remove the back door lock cylinder (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Key Condition
    Specified Condition
    1 - 2
    Lock position
    Below 1 Ω
    1 - 2
    Unlock position
    10 kΩ or higher
    1 - 3
    Lock position
    10 kΩ or higher
    1 - 3
    Unlock position
    Below 1 Ω

  1. Reinstall the the back door lock cylinder.



NG
REPLACE BACK DOOR LOCK CYLINDER (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK CYLINDER - BACK DOOR ECU)
B138202E02
  1. Disconnect the S5 back door ECU connector.

  1. Disconnect the S7 back door lock cylinder connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection
Condition
Specified Condition
S7-2 - S5-5 (L)
Always
Below 1 Ω
S7-3 - S5-4 (UL)
Always
Below 1 Ω
S7-2 or S5-5 (L) - Body ground
Always
10 kΩ or higher
S7-3 or S5-4 (UL) - Body ground
Always
10 kΩ or higher

  1. Reconnect the back door ECU connector.

  1. Reconnect the back door lock cylinder connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK DOOR ECU (Click here)  

5.INSPECT BACK DOOR LOCK
  1. Remove the back door lock (Click here).



    B135520E03
  1. Apply the battery voltage to the door lock motor and check the operation of the door lock motor.

    Standard:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1 (ACT+)
    Battery negative(-) → Terminal 2 (ACT-)
    Locks
    Battery positive (+) → Terminal 2 (ACT-)
    Battery negative(-) → Terminal 1 (ACT+)
    Unlocks

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Door Lock Condition
    Specified Condition
    4 (S) - 5 (E)
    Locked
    10 kΩ or higher
    4 (S) - 5 (E)
    Unlocked
    Below 1 Ω



NG
REPLACE BACK DOOR LOCK (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BACK DOOR LOCK)
B175119E02
  1. Disconnect the 1F main body ECU connector.

  1. Disconnect the S4 back door lock connector.

  1. Disconnect the S5 back door ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S5-15 (ACT+) - S4-1 (ACT+)
    Always
    Below 1 Ω
    S5-14 (ACT-) - S4-2 (ACT-)
    Always
    Below 1 Ω
    1F-4 (LSR) - S4-4 (S)
    Always
    Below 1 Ω
    S4-5 (E) - Body ground
    Always
    Below 1 Ω
    S5-15 (ACT+) or S4-1 (ACT+) - Body ground
    Always
    10 kΩ or higher
    S5-14 (ACT-) or S4-2 (ACT-) - Body ground
    Always
    10 kΩ or higher
    1F-4 (LSR) or S4-4 (S) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the back door lock connector.

  1. Reconnect the back door ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK DOOR ECU (Click here)