Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1830/57    Short in Curtain Shield Squib RH Circuit

DTC    B1831/57    Open in Curtain Shield Squib RH Circuit

DTC    B1832/57    Short to GND in Curtain Shield Squib RH Circuit

DTC    B1833/57    Short to B+ in Curtain Shield Squib RH Circuit

for Preparation Click here


DESCRIPTION

The curtain shield squib RH circuit consists of the center airbag sensor assembly and curtain shield airbag assembly RH.
The center airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the curtain shield squib RH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1830/57
  1. The center airbag sensor assembly receives a line short circuit signal in the curtain shield squib RH circuit during primary check.
  2. Curtain shield squib RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Curtain shield airbag assembly RH (Curtain shield squib RH)
  3. Center airbag sensor assembly
B1831/57
  1. The center airbag sensor assembly receives an open circuit signal in the curtain shield squib RH circuit.
  2. Curtain shield squib RH malfunction
  3. Center airbag sensor assembly malfunction
B1832/57
  1. The center airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib RH circuit.
  2. Curtain shield squib RH malfunction
  3. Center airbag sensor assembly malfunction
B1833/57
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib RH circuit.
  2. Curtain shield squib RH malfunction
  3. Center airbag sensor assembly malfunction

WIRING DIAGRAM


C268593E05


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

HINT:
  1. Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (Click here).
  2. After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (Click here).

1.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the curtain shield airbag assembly RH and center airbag sensor assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the curtain shield airbag assembly RH and center airbag sensor assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the floor wire connector (on the curtain shield airbag assembly side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

  1. Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


2.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH
SST
09843-18061  


    C268594E02
  1. Connect the connector to the center airbag sensor assembly.

  1. Connect SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the curtain shield airbag assembly RH (curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting it.
    2. Insert SST straight into the terminals of the connector.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1830/57, B1831/57, B1832/57 or B1833/57 is not output.

    HINT:
    Codes other than DTCs B1830/57, B1831/57, B1832/57 and B1833/57 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Disconnect SST from connector C.
    Text in Illustration 
    *1
    Curtain Shield Airbag Assembly RH
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Curtain Shield Airbag Assembly RH)



NG
Go to step 3
OK

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH (Click here)  

3.CHECK FLOOR WIRE


    C268595E02
  1. Disconnect the floor wire from the center airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      K5-1 (ICR+) - Body ground
      Ignition switch ON
      Below 1 V
      K5-2 (ICR-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check for an open in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K5-1 (ICR+) - K5-2 (ICR-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K5-1 (ICR+) - Body ground
      Always
      1 MΩ or higher
      K5-2 (ICR-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K5-1 (ICR+) - K5-2 (ICR-)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.
      Text in Illustration 
      *1
      Curtain Shield Airbag Assembly RH
      *2
      Center Airbag Sensor Assembly
      *3
      Floor Wire
      *a
      Front view of wire harness connector
      (to Curtain Shield Airbag Assembly RH)



NG
REPLACE FLOOR WIRE
OK


4.CHECK DTC


    C268589E05
  1. Connect the connectors to the curtain shield airbag assembly RH and center airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1830/57, B1831/57, B1832/57 or B1833/57 is not output.

    HINT:
    Codes other than DTCs B1830/57, B1831/57, B1832/57 and B1833/57 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Curtain Shield Airbag Assembly RH
    *2
    Center Airbag Sensor Assembly



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)