Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Open in One Side of CAN Branch Line

for Preparation Click here


DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the Techstream "CAN Bus Check" screen, one side of the CAN branch wire may be open (One side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open).

Symptom
Trouble Area
2 or more ECUs and/or sensors do not appear on the Techstream "CAN Bus Check" screen.
  1. One side of CAN branch wire is open
  2. Airbag sensor assembly
  3. Yaw rate sensor
  4. Master cylinder solenoid (skid control ECU)
  5. Driving support switch control ECU*1
  6. Steering angle sensor
  1. *1: w/ CRAWL

WIRING DIAGRAM


E257629E05


INSPECTION PROCEDURE

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the ignition switch off before inspecting CAN bus wires for a ground short.
  3. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, first disconnect the cable from the negative battery terminal and confirm that the alarm function is no longer operating. Then, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.
  5. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
  1. Perform the following inspection for the ECUs (sensors) which are not displayed on the Techstream. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.
  1. Do not remove the center airbag sensor assembly and ECM, as they are the end parts of the circuit. If removed, CAN communication will not be possible.
  1. The open circuit confirmation of the center airbag sensor assembly, ECM and main wire is performed in the Check CAN Bus Line procedure of How to Proceed with Troubleshooting. This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.

1.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (YAW RATE SENSOR)
  1. Disconnect the E81 yaw rate sensor connector.

  1. Select "CAN Bus Check" on the Techstream (Click here).
    Result 
    Result
    Proceed to
    "Yaw Rate / Deceleration Sensor" not displayed on the Techstream.
    A
    Several ECUs and sensors other than "Yaw Rate / Deceleration Sensor" not displayed on the Techstream.
    B



B
Go to step 3
A


2.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (YAW RATE SENSOR BRANCH WIRE)


    E175983E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E81-3 (CANH) - E81-2 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE YAW RATE SENSOR (Click here)  

3.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (MASTER CYLINDER SOLENOID (SKID CONTROL ECU))
  1. Disconnect the A4 master cylinder solenoid (skid control ECU) connector.

  1. Select "CAN Bus Check" on the Techstream (Click here).
    Result 
    Result
    Proceed to
    "ABS/VSC/TRAC" not displayed on the Techstream.
    A
    Several ECUs and sensors other than "ABS/VSC/TRAC" not displayed on the Techstream.
    B



B
Go to step 5
A


4.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (MASTER CYLINDER SOLENOID (SKID CONTROL ECU) BRANCH WIRE)


    E191994E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-11 (CANH) - A4-25 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid (Skid Control ECU))



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)  

5.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (AIRBAG SENSOR ASSEMBLY)
  1. Disconnect the E29 airbag sensor assembly connector.

  1. Select "CAN Bus Check" on the Techstream (Click here).
    Result 
    Result
    Proceed to
    "SRS Airbag" not displayed on the Techstream.
    A
    Several ECUs and sensors other than "SRS Airbag" not displayed on the Techstream.
    B



B
Go to step 7
A


6.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
E186790E14
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E29-13 (CANH) - E29-22 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

7.SYSTEM CHECK
  1. Check the vehicle specifications.
    Result 
    Result
    Proceed to
    w/ CRAWL
    A
    w/o CRAWL
    B



B
Go to step 9
A


8.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (DRIVING SUPPORT SWITCH CONTROL ECU)
  1. Disconnect the E89 driving support switch control ECU.

  1. Select "CAN Bus Check" on the Techstream (Click here).
    Result 
    Result
    Proceed to
    "D-SEAT SW" not displayed on the Techstream.
    A
    Several ECUs and sensors other than "D-SEAT SW" not displayed on the Techstream.
    B



B
Go to step 10
A


9.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (DRIVING SUPPORT SWITCH CONTROL ECU)


    E257628E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal No. (Symbol)
    Switch Condition
    Specified Condition
    E89-8 (CANH) - E89-3 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Driving Support Switch Control ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU (Click here)  

10.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (STEERING ANGLE SENSOR BRANCH WIRE)
E192049E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-3 (CANH) - E16-11 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE STEERING ANGLE SENSOR (Click here)