Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > VSC OFF Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

Operation of the VSC OFF switch changes the vehicle between normal mode, TRAC OFF mode*1 (AUTO LSD mode*2) and VSC OFF mode. During normal mode, pressing the VSC OFF switch for a short amount of time changes vehicle to TRAC OFF mode*1 (AUTO LSD mode*2). When the vehicle is stopped, pressing the VSC OFF switch for 3 seconds or more changes the vehicle to VSC OFF mode.
  1. *1: for 4WD
  2. *2: for 2WD
for 4WD:
  1. When the transfer is in L4(for automatic transmission) or LL(for manual transmission), VSC is prohibited and the VSC OFF indicator and TRAC OFF indicator lights turn on.
  2. w/ Rear Differential Lock:
    When the rear differential is locked, VSC is prohibited and the VSC OFF indicator and TRAC OFF indicator lights turn on. At this time, ABS is also prohibited and the ABS warning light turns on.

WIRING DIAGRAM


C271670E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform calibration (Click here).
  2. As there may be malfunctions in the transfer system related to when the transfer operates in L4(for automatic transmission) or LL(for manual transmission), check the transfer system first (for automatic transmission: Click here, for manual transmission: Click here).

1.CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU CSW CIRCUIT)
  1. Disconnect the A4 skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-9 (CSW) - Body ground
    VSC OFF switch not pushed in
    10 kΩ or higher
    VSC OFF switch pushed in
    Below 1 Ω



NG
Go to step 5
OK


3.INSPECT SKID CONTROL ECU (EXI3 TERMINAL)


  1. for w/ Rear Differential Lock

    1. Disconnect the A4 skid control ECU connector.



    2. C214161E52
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A4-40 (EXI3) - Body ground
      Ignition switch ON
      w/ Rear Differential Lock: Rear differential free
      11 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Skid Control ECU)



  1. for w/o Rear Differential Lock

    1. Disconnect the A4 skid control ECU connector.



    2. C214161E52
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A4-40 (EXI3) - Body ground
      Ignition switch ON
      11 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Skid Control ECU)
      Result 
      Result
      Proceed to
      OK
      A
      NG (for w/ Rear Differential Lock)
      B
      NG (for w/o Rear Differential Lock)
      C



B
Go to step 7

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


4.READ VALUE USING TECHSTREAM (TRAC/VSC OFF MODE)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.


ABS/VSC/TRAC 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
TRAC/VSC Off Mode
TRAC/VSC off mode/ Normal, TRC OFF or VSC OFF
Normal: Normal mode
TRC OFF: TRAC OFF mode
VSC OFF: VSC OFF mode
-
  1. Check that the mode display changes according to VSC OFF switch operation.

    OK:
    Display changes according to switch operation.



NG
REPLACE MASTER CYLINDER SOLENOID (Click here)
OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)  

5.INSPECT VSC OFF SWITCH
  1. Remove the VSC OFF switch (Click here).



    C234071E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 - 4
    Switch is not pushed
    10 kΩ or higher
    Switch is pushed
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (VSC OFF Switch)



NG
REPLACE VSC OFF SWITCH (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
  1. Disconnect the A4 skid control ECU connector.

  1. Disconnect the E3 VSC OFF switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-9 (CSW) - E3-3
    Always
    Below 1 Ω
    A4-9 (CSW) - Body ground
    Always
    10 kΩ or higher
    E3-4 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)  

7.INSPECT SKID CONTROL ECU (EXI3 TERMINAL)
  1. Disconnect the A4 skid control ECU connector.

  1. Disconnect the L7 four wheel drive control ECU connector.

  1. Disconnect the D2 rear differential lock indicator switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-40 (EXI3) - Body ground
    Always
    10 kΩ or higher



B
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


8.INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH)
  1. Remove the rear differential lock detection switch (Click here).



    C214518E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (+B) - 1 (GND)
    Pushed in
    Below 1 Ω
    Not pushed in
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Differential Lock Indicator Switch)



NG
REPLACE DIFFERENTIAL LOCK INDICATOR SWITCH (REAR DIFFERENTIAL LOCK DETECTION SWITCH) (Click here)
OK


9.INSPECT SKID CONTROL ECU (EXI3 TERMINAL)
  1. Disconnect the A4 skid control ECU connector.

  1. Connect the L7 four wheel drive control ECU connector.



    C214161E52
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-40 (EXI3) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPLACE 4 WHEEL DRIVE CONTROL ECU NO.2
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)