VEHICLE STABILITY CONTROL SYSTEM > TRAC OFF Indicator Light Remains ON |

| 1.CHECK DTC (ENGINE CONTROL SYSTEM) |
Check if any DTC is recorded for the engine control system (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 2.CHECK CAN COMMUNICATION LINE |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CSW CIRCUIT) |
Disconnect the A4 skid control ECU (master cylinder solenoid) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A4-9 (CSW) - Body ground | VSC OFF switch not pushed in | 10 kΩ or higher |
| VSC OFF switch pushed in | Below 1 Ω |
|
| ||||
| OK | |
| 4.INSPECT MASTER CYLINDER SOLENOID (EXI3 TERMINAL) |
w/ Rear Differential Lock
Disconnect the A4 skid control ECU (master cylinder solenoid) connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A4-40 (EXI3) - Body ground | Ignition switch ON Rear differential free | 11 to 14 V |
| *a | Front view of wire harness connector (to skid control ECU (master cylinder solenoid)) |
w/o Rear Differential Lock
Disconnect the A4 skid control ECU (master cylinder solenoid) connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A4-40 (EXI3) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to skid control ECU (master cylinder solenoid)) |
| Result | Proceed to |
| OK | A |
| NG (w/ Rear Differential Lock) | B |
| NG (w/o Rear Differential Lock) | C |
|
| ||||
|
| ||||
| A | |
| 5.READ VALUE USING TECHSTREAM (TRAC/VSC OFF MODE) |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| TRAC/VSC Off Mode | TRAC/VSC off mode/ Normal, TRC OFF or VSC OFF | Normal: Normal mode TRC OFF: TRAC OFF mode VSC OFF: VSC OFF mode | - |
Check that the mode display changes according to VSC OFF switch operation.
|
| ||||
| OK | ||
| ||
| 6.INSPECT VSC OFF SWITCH |
Remove the VSC OFF switch (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 3 - 4 | Switch is not pushed | 10 kΩ or higher |
| Switch is pushed | Below 1 Ω |
| *a | Component without harness connected (VSC OFF Switch) |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - VSC OFF SWITCH) |
Disconnect the A4 skid control ECU (master cylinder solenoid) connector.
Disconnect the E3 VSC OFF switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A4-9 (CSW) - E3-3 | Always | Below 1 Ω |
| A4-9 (CSW) - Body ground | Always | 10 kΩ or higher |
| E3-4 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 8.INSPECT MASTER CYLINDER SOLENOID (EXI3 CIRCUIT) |
Disconnect the A4 skid control ECU (master cylinder solenoid) connector.
Disconnect the L7 four wheel drive control ECU connector.
Disconnect the D2 rear differential lock detection switch (differential lock indicator switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A4-40 (EXI3) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH) |
Remove the rear differential lock detection switch (differential lock indicator switch) (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 2 | Pushed in | Below 1 Ω |
| Not pushed in | 10 kΩ or higher |
| *a | Component without harness connected (Differential Lock Indicator Switch) |
|
| ||||
| OK | |
| 10.INSPECT MASTER CYLINDER SOLENOID (EXI3 TERMINAL) |
Disconnect the A4 skid control ECU (master cylinder solenoid) connector.
Connect the L7 four wheel drive control ECU connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A4-40 (EXI3) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to skid control ECU (master cylinder solenoid)) |
|
| ||||
| OK | ||
| ||