2TR-FE MANUAL TRANSMISSION ASSEMBLY > INSTALLATION |
| 1. INSTALL WIRE HARNESS CLAMP BRACKET |
![]() |
Install the wire harness clamp bracket.
| 2. INSTALL TRANSMISSION CONTROL CABLE BRACKET NO.1 |
Install the transmission control cable bracket No.1 with the 2 bolts.
| 3. INSTALL REAR ENGINE MOUNTING INSULATOR ASSEMBLY |
![]() |
Install the rear engine mounting insulator assembly with the 4 bolts.
| 4. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY |
![]() |
Install the transmission unit assembly with the 8 bolts.
![]() |
Install the transmission unit assembly to the frame with the bolt, nut, and 2 washers.
| 5. INSTALL STARTER ASSEMBLY |
![]() |
Install the starter with the 2 bolts.
Connect the wire harness to terminal 30 and install the nut.
Connect the terminal 50 connector to the starter assembly.
![]() |
Install the ground cable and wire bracket with the 2 bolts.
| 6. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY |
![]() |
Install the clutch release cylinder with the 2 bolts.
| 7. INSTALL WIRE HARNESS |
![]() |
Connect the 2 connectors and clamps.
| 8. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Install 2 new clips to the transmission control cable bracket No.1.
Install the transmission control cable assembly to the transmission control cable bracket No.1.
![]() |
Align the matchmarks on the control cable assembly and the outer lever.
Install the transmission control cable assembly to the outer levers with the 2 nuts.
| 9. INSTALL PROPELLER SHAFT ASSEMBLY (for Long Wheelbase) |
![]() |
Remove the SST from the extension housing.
Install the propeller shaft assembly in the extension housing.
Align the matchmarks on the propeller shaft flange and differential flange.
![]() |
Install the propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.
| 10. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Super Long Wheelbase) |
![]() |
Remove the SST from the extension housing.
Install the propeller with center bearing shaft assembly in the extension housing.
![]() |
Install the center support bearing assembly No.1, and temporarily tighten the 2 bolts.
![]() |
Align the matchmarks on the propeller shaft flange and differential flange.
Install the propeller shaft assy with the 4 nuts, 4 bolts and 4 washers.
![]() |
Check that the center line of the bracket is at right angles to the shaft axial direction.
![]() |
Adjust the center support bearing assembly No.1.
Tighten the 2 bolts.
| 11. INSTALL EXHAUST PIPE ASSEMBLY FRONT (for Long Wheelbase) |
w/ Secondary air injection system:
Install the fuel ratio sensor. (Click here)
For unleaded gasoline engine:
Install the oxygen sensor. (Click here)
Inspect the compression spring.
![]() |
Using vernier calipers, measure the free length of the compression springs.
![]() |
Install the gasket.
Fully insert a new gasket to the exhaust manifold by hand.
Using a wooden block, uniformly strike the gasket so that the gasket and exhaust manifold are properly fit.
Install a new gasket to the exhaust pipe assembly front.
Connect the exhaust pipe assembly front to the exhaust pipe support.
Install the exhaust pipe assembly front with the 4 bolts, 2 nuts, and 2 compression springs.
For unleaded gasoline engine:
Connect the sensor connector(s).
| 12. INSTALL EXHAUST PIPE ASSEMBLY FRONT (for Super Long Wheelbase) |
w/ Secondary air infection system:
Install the air fuel ratio sensor. (Click here)
For Unleaded gasoline engine:
Install the oxygen sensor. (Click here)
Inspect the compression spring.
![]() |
Using vernier calipers, measure the free length of the compression springs.
![]() |
Install the gasket.
Fully insert a new gasket to the exhaust manifold by hand.
Using a wooden block, uniformly strike the gasket so that the gasket and exhaust manifold are properly fit.
Install a new gasket to the exhaust pipe assembly front.
Connect the exhaust pipe assembly front to the exhaust pipe support.
Install the exhaust pipe assembly front with the 4 bolts, 2 nuts, and 2 compression springs.
For Unleaded gasoline engine:
Connect the sensor connector(s).
| 13. ADD MANUAL TRANSMISSION OIL |
![]() |
Park the vehicle in a level place.
Remove the transmission filler plug and gasket.
Check that the oil surface is within 5 mm (0.20 in.) below the lowest point of the transmission filler plug opening.
Check for oil leakage if the oil level is low.
Install the transmission filler plug and a new gasket.
| 14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 15. CHECK FOR EXHAUST GAS LEAKS |
| 16. PERFORM INITIALIZATION |