Home › TRANSMISSION ยท A343E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY


    C102921E01
  1. Using vernier calipers measure the dimension A between the transmission and the end of the surface of the drive plate.



    C101844E01
  1. Aligning the matchmarks on the transmission case and torque converter assembly, engage the spline of the input shaft and turbine runner.

    NOTICE:
    Install the torque converter assembly to the input shaft in horizontally.



    C101845E01
  1. Engage the spline of the stator shaft and stator while turning the torque converter assembly to a clockwise.

    NOTICE:
    1. Turn the torque converter assembly approximately 180°.
    2. Be sure not to damage the oil seal.
    3. Install the torque converter assembly to the input shaft in horizontally.



    C101846E01
  1. Turn the torque converter assembly to the clockwise and align the match marks on the torque converter assembly and transmission case to engage the key of the oil pump drive gear into the slot on the torque converter assembly.

    NOTICE:
    1. Do not push the torque converter when align the match marks.
    2. Be sure not to damage the oil seal.
    3. Install the torque converter assembly to the input shaft horizontally.



    C101847E01
  1. Using calipers and a straight edge, measure dimension B shown in the illustration and check that B is greater than A measured in step (a).

    Standard:
    A + 1 mm(0.04 in) or more



2. INSTALL BREATHER PLUG HOSE


    C103234E02
  1. Install the breather plug hose with the bolt.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



3. INSTALL ENGINE MOUNTING INSULATOR ASSEMBLY REAR


    C102922E02
  1. Install the engine mounting insulator assembly rear with 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



4. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


    C103762E01
  1. Install the automatic transmission assembly with 8 bolts.

    Torque:
    Bolt A:
    71 N*m{ 724 kgf*cm , 55 ft.*lbf }
    Bolt B, C:
    37 N*m{ 377 kgf*cm , 29 ft.*lbf }



5. INSTALL ENGINE MOUNTING INSULATOR ASSEMBLY REAR


    C101781
  1. Install the engine mounting insulator assembly rear with bolt, nut and 2 washers.

    Torque:
    98 N*m{ 999 kgf*cm , 77 ft.*lbf }



6. INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT


    C102925E02
  1. Turn the crankshaft pulley and install the 6 torque converter clutch setting bolts.

    Torque:
    41 N*m{ 420 kgf*cm , 32 ft.*lbf }

    HINT:
    First install the match mark bolt (black painted).



    C102926E02
  1. Install the flywheel housing dust seal to the automatic transmission assembly.



7. INSTALL WIRE HARNESS


    C102927E02
  1. Install the wire harness to the automatic transmission assembly with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf }



8. CONNECT CONNECTOR


    C102929E04
  1. Connect the connector of park/neutral position switch connector and temperature sensor.



    C101834E04
  1. Install the heat insulator to the park/neutral position switch assembly with 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 65 in.*lbf }



    C101774E03
  1. Install the speed sensor ()and connector of transmission wire.



    C102928E01
  1. Connect the speed sensor (NCO) connector and temperature sensor connector.



9. INSTALL OIL COOLER TUBE


    C102930E02
  1. Install the 2 oil cooler tube to the automatic transmission.

    SST
    09023-12701  

    Torque:
    34 N*m{ 347 kgf*cm , 26 ft.*lbf }



  1. Install the 3 oil cooler tube clamps with 3 bolts.

    Torque:
    Bolt A:
    12 N*m{ 125 kgf*cm , 8 ft.*lbf }
    Bolt B:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    C102932E01



10. INSTALL STARTER ASSEMBLY


    A102709E01
  1. Remove the 2 bolts, then remove the ground cable and bracket.



    A113538E02
  1. Remove the nut and disconnect the wire harness from terminal 30.

  1. Disconnect the terminal 50 connector from the starter assembly.

  1. Remove the 2 bolts and the starter assembly.



11. INSTALL TRANSMISSION CONTROL CABLE BRACKET NO.1


    C102931E03
  1. Install the transmission control cable bracket to the automatic transmission assembly with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 11 ft.*lbf }



12. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


    C102933E04
  1. Install the transmission control cable assembly to the control shaft lever and transmission control bracket No.1 with the nut and a new clip.

    Torque:
    15 N*m{ 150 kgf*cm , 11 ft.*lbf }



13. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


    C102934E06
  1. Coat a new O-ring with ATF and install the oil filler tube.

  1. Install the oil filler tube with 2 bolts.

    Torque:
    12 N*m{ 125 kgf*cm , 10 ft.*lbf }



14. INSTALL EXHAUST PIPE ASSEMBLY FRONT
  1. w/ Secondary air injection system:

    1. Install the fuel ratio sensor. (Click here)

      Torque:
      44 N*m{ 449 kgf*cm , 32 ft.*lbf }

  1. For unleaded gasoline engine:

    1. Install the oxygen sensor. (Click here)

      Torque:
      44 N*m{ 449 kgf*cm , 32 ft.*lbf }



  1. Inspect the compression spring.



      A077857
    1. Using vernier calipers, measure the free length of the compression springs.

      Minimum length:
      40.5mm(1.594 in.)

      HINT:
      If the free length is less than the minimum, replace the compression spring.



    A102062E03
  1. Install the gasket.

    1. Fully insert a new gasket to the exhaust manifold by hand.

    2. Using a wooden block, uniformly strike the gasket so that the gasket and exhaust manifold are properly fit.

      NOTICE:
      1. Be careful with the installation direction of the gasket.
      2. Do not reuse the gasket.
      3. Do not damage the gasket.
      4. To ensure a proper seal, do not use the exhaust pipe assembly front to force the gasket onto the exhaust manifold.

  1. Install a new gasket to the exhaust pipe assembly front.

  1. Connect the exhaust pipe assembly front to the exhaust pipe support.

  1. Install the exhaust pipe assembly front with the 4 bolts, 2 nuts, and 2 compression springs.

    Torque:
    Exhaust manifold side:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    Torque:
    Exhaust pipe assembly tail side:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    After installation, check that the clearance is almost the same at any point between the flanges of the exhaust manifold and exhaust pipe assembly front.

  1. For unleaded gasoline engine:

    1. Connect the sensor connector(s).



15. INSTALL PROPELLER SHAFT ASSEMBLY


    C102186E01
  1. Remove the SST from the extension housing.

  1. Install the propeller shaft assembly in the extension housing.

  1. Align the matchmarks on the propeller shaft flange and differential flange.



    C102185E01
  1. Install the propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.

    Torque:
    74 N*m{ 755 kgf*cm , 54 ft.*lbf }



16. INSTALL ENGINE SIDE UNDER COVER LH


17. INSTALL ENGINE SIDE UNDER COVER RH


18. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY NO.2


19. INSTALL ENGINE UNDER COVER NO.1


20. CONNECT BATTERY NEGATIVE CABLE


21. ADD AUTOMATIC TRANSMISSION FLUID


22. INSPECT AUTOMATIC TRANSMISSION FLUID

HINT:
Drive the vehicle so that the engine and transmission are at normal operating temperature.

Fluid temperature:
70 to 80 °C (158 to 176 °F)



    D025120E01
  1. Park the vehicle on a level surface and set the parking brake.

  1. With the engine idling and the brake pedal depressed, move shift the lever into all positions from P to L and return to the P position.

  1. Take out the dipstick and wipe it clean.

  1. Put it back all the way.

  1. Take it out again and check that the fluid level is within the HOT range.
    If the fluid level is below the HOT range, add new fluid and recheck the fluid level. If the fluid level exceeds the HOT range, drain the fluid once, add the proper amount of new fluid and recheck the fluid level.



23. INSPECT SHIFT LEVER POSITION
  1. When shifting from P position only with ignition switch ON and depress the break pedal.

  1. Make sure that the shifting lever moves smoothly and can be moderately operated.

  1. When starting engine, make sure that the vehicle moves forward when shifting from N to D position and moves reward when shifting R position.



24. ADJUST SHIFT LEVER POSITION


    C101771E02
  1. Remove a clip, nut, and disconnect between the control shaft lever to transmission control cable assembly from the control shaft lever and transmission control cable bracket No.1.



    C101788E05
  1. Turn the control shaft lever until stop to a clockwise direction, return the control shaft lever 2 notches to N position.



    C101803
  1. Set the shift lever to N position while holding the shift lever lightly toward the R position side and install it.

    Torque:
    15 N*m{ 150 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Tighten the nut with it closing up cranky.

  1. Inspect the operation condition and work.



25. CHECK EXHAUST GAS LEAKS


26. PERFORM INITIALIZATION
(Click here)