Home › ENGINE ยท 2TR-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here



1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


2. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT
(Click here)


3. SEPARATE BATTERY NEGATIVE CABLE


4. REMOVE FRONT WHEELS


5. REMOVE ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1)


6. REMOVE ENGINE UNDER COVER NO.2 (w/ Engine Under Cover No.2)


7. REMOVE ENGINE SIDE UNDER COVER LH (w/ Engine Side Under Cover LH)


8. REMOVE ENGINE SIDE UNDER COVER RH (w/ Engine Side Under Cover RH)


9. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the radiator cap.



  1. Loosen the radiator drain plug and a cylinder block drain plug. Then drain the coolant.


    A115990E01



10. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and drain the engine oil from the oil pan.

    NOTICE:
    Collect the oil in a disposable oil container.

  1. Clean the oil pan drain plug and install it with a new gasket.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



11. REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)

HINT:
Use the same procedures described for the LH side.



12. REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)

HINT:
Use the same procedures described for the LH side.



13. REMOVE FRONT DOOR SCUFF PLATE


14. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Roll up the carpet, and remove the 5 bolts and engine service hole sub cover.



15. REMOVE FAN AND GENERATOR V BELT


    A102135E01
  1. Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward and decrease the tension in the drive belt. Then remove the drive belt.

    NOTICE:
    When removing the drive belt, do not use the idle pulley's bolt.

    HINT:
    After removing the drive belt, move the tensioner upward to the maximum amount.



16. DISCONNECT RADIATOR HOSE INLET
  1. Remove the clamp, and disconnect the radiator hose inlet from the engine.



17. DISCONNECT RADIATOR HOSE OUTLET
  1. Remove the clamp, and disconnect the radiator hose outlet from the engine.



18. DISCONNECT HEATER WATER INLET HOSE A
  1. Disconnect the heater water inlet hose A from the heater unit.



19. DISCONNECT HEATER WATER OUTLET HOSE B
  1. Disconnect the heater water outlet hose B from the heater unit.



20. DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY


    A103325
  1. Disconnect the fuel vapor feed hose from the VSV.



21. DISCONNECT UNION TO CONNECTOR TUBE HOSE
  1. Disconnect the union to connector tube hose from the intake manifold.



22. REMOVE INTAKE AIR CONNECTOR


    A102437E01
  1. Disconnect the ventilation hose No.2 and the vacuum hose.(A)

  1. Loosen the 2 hose clamp bolts.(B)

  1. Remove the 2 bolts, then remove the intake air connector.(C)



23. DISCONNECT AIR HOSE NO.5 (w/ Secondary Air Injection System)
  1. Disconnect the air hose No.5 from the air switching valve.



24. DISCONNECT FUEL HOSE


    A087751E01
  1. Pull the fuel hose connector cover up to release the lock. (Click here)

  1. Disengage the fuel connector to disconnect the fuel hose. (Click here)



25. DISCONNECT FUEL HOSE NO.2
  1. Remove the clamp, and disconnect the fuel hose No.2 from the delivery pipe.



26. DISCONNECT VANE PUMP ASSEMBLY


    A102130E01
  1. Disconnect the PS fluid pressure switch connector.

  1. Remove the 2 bolts and disconnect the pump from the engine.

  1. Support the vane pump securely.



27. REMOVE OIL LEVEL GAUGE SUB-ASSEMBLY


28. REMOVE OIL LEVEL GAUGE GUIDE


    A102132E01
  1. Remove the bolt and gauge guide.



29. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning)
  1. Disconnect the compressor connector.



    A102804E02
  1. Remove the 4 bolts and disconnect the compressor from the engine.

    HINT:
    Disconnect the compressor with the low pressure hose and high pressure hose stuck by suspended from the rope.

  1. Support the cooler compressor securely.



30. DISCONNECT ENGINE WIRE
  1. Disconnect the wire harness support of the ECM.

  1. Disconnect the connectors of the ECM.

  1. Disconnect the clamps of the engine wire and earth cable.

  1. Disconnect the +B terminal of the starter and connector from the generator.



    A101143E03
  1. Remove the nut and disconnect the cable from the engine room J/B.



31. REMOVE EXHAUST PIPE ASSEMBLY FRONT (for Super Long Wheelbase)
  1. w/ Secondary air injection system:

    1. Disconnect the fuel ratio sensor connector.

    2. Remove the fuel ratio sensor. (Click here)

  1. For unleaded gasoline engine:

    1. Disconnect the oxygen sensor connector.

    2. Remove the oxygen sensor. (Click here)

  1. Remove the 4 bolts, 2 nuts, and 2 compression springs.

  1. Remove the 2 gaskets from the exhaust pipe assembly front.

  1. Disconnect the exhaust pipe support, and remove the exhaust pipe assembly front.



32. REMOVE EXHAUST PIPE ASSEMBLY FRONT (for Long Wheelbase)
  1. w/ Secondary air infection system:

    1. Disconnect the fuel ratio sensor connector.

    2. Remove the fuel ratio sensor. (Click here)

  1. For unleaded gasoline engine:

    1. Disconnect the oxygen sensor connector.

    2. Remove the oxygen sensor. (Click here)

  1. Remove the 4 bolts, 2 nuts, and 2 compression springs.

  1. Remove the 2 gaskets from the exhaust pipe assembly front.

  1. Disconnect the exhaust pipe support, and remove the exhaust pipe assembly front.



33. REMOVE EXHAUST PIPE ASSEMBLY CENTER (for Super Long Wheelbase)
  1. Remove the 2 bolts and gasket from the exhaust pipe assembly center.

  1. Disconnect the exhaust pipe supports, and remove the exhaust pipe assembly center.



34. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Super Long Wheelbase)


    C102185E01
  1. Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller with center bearing shaft assembly from the differential companion flange.



    C107214
  1. Remove the 2 bolts and center support bearing assembly No.1.

  1. Remove the propeller with center bearing shaft assembly.



    C102186E01
  1. Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission.

      SST
      09325-40010  

    2. Use the following SST for the manual transmission.

      SST
      09325-20010  



35. REMOVE PROPELLER SHAFT ASSEMBLY (for Long Wheelbase)


    C102185E01
  1. Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller shaft assembly from the differential companion flange.

  1. Remove the propeller shaft assembly.



    C102186E01
  1. Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission

      SST
      09325-40010  

    2. Use the following SST for the manual transmission

      SST
      09325-20010  



36. REMOVE SPEED SENSOR FRONT LH (w/ ABS)


    C102281E01
  1. Remove the 2 bolts, and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Be careful not to damage the speed sensor.
    2. Prevent foreign matter from adhering to the speed sensor.



37. REMOVE SPEED SENSOR FRONT RH (w/ ABS)

HINT:
Use the same procedures described for the LH side.



38. REMOVE FRONT DISC BRAKE CALIPER ASSEMBLY LH


    C102283E01
  1. Remove the 2 bolts, and disconnect the brake caliper assembly.

    NOTICE:
    Use a wire or an equivalent to keep the brake caliper from hanging down by the flexible hose.



39. REMOVE FRONT DISC BRAKE CALIPER ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



40. SEPARATE FRONT SUSPENSION SUB-ASSEMBLY UPPER LH


    C101998E01
  1. Remove the cotter pin and loosen the nut.

    SST
    09628-62011  

    NOTICE:
    Do not remove the nut.

  1. Using SST, separate the steering knuckle from the suspension upper arm and remove the nut.

    NOTICE:
    1. Fix the steering knuckle with a wire so that the flexible hose does not receive excessive force.
    2. Do not damage the ball joint dust cover.



41. SEPARATE FRONT SUSPENSION SUB-ASSEMBLY UPPER RH

HINT:
Use the same procedures described for the LH side.



42. SEPARATE SHOCK ABSORBER ASSEMBLY FRONT LH


    C102009E02
  1. Remove the bolt and separate the front shock absorber from the front suspension lower arm.



43. SEPARATE SHOCK ABSORBER ASSEMBLY FRONT RH

HINT:
Use the same procedures described for the LH side.



44. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transmission)


    C102206E01
  1. Put matchmarks on the control cable assembly and the outer lever.

  1. Remove the 2 nuts and separate the transmission control cable from the outer lever.



    C102207
  1. Using a screwdriver, disengage the claws of the 2 clips.

  1. Remove the transmission control cable and 2 clips from the transmission control cable bracket No.1.



45. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transmission)


    C102209
  1. Remove the 2 bolts and separate the clutch release cylinder.



46. REMOVE TRANSMISSION OIL LEVEL GAUGE SUB-ASSEMBLY (for Automatic Transmission)


    C102919
  1. Remove the transmission oil level gage sub assembly from the transmission oil filler tube.



47. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY (for Automatic Transmission)


    C102934E01
  1. Remove the 2 bolts transmission oil filler tube sub-assembly.

  1. Remove the O-ring from the oil filler tube sub-assembly.



48. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)


    C102933E05
  1. Remove the nut and disconnect the transmission control cable assembly from the transmission control shaft lever assembly.

  1. Remove the clip and disconnect the transmission control cable assembly from the transmission control cable bracket.



49. DISCONNECT OIL COOLER HOSE (for Automatic Transmission)
  1. Remove each clamp and disconnect the oil cooler inlet hose and oil cooler outlet hose from the oil cooler tube.



50. SEPARATE STEERING TORQUE SHAFT ASSEMBLY


    C106142E01
  1. Loosen bolt (A) and remove bolt (B), then slide the steering torque shaft assembly.

    HINT:
    1. Do not remove bolt (A).
    2. Do not disconnect the steering torque shaft assembly from the power steering link assembly.



    C106143E01
  1. Put matchmarks on the steering torque shaft assembly and the power steering link assembly.

  1. Separate the steering torque shaft assembly from the power steering link assembly.



51. REMOVE ENGINE ASSEMBLY WITH TRANSMISSION
  1. Using the engine lifter, hold the engine assembly and separate the rear engine mount.



    A101144E04
  1. Remove the stabilizer brackets and 16 bolts of the front suspension cross member.

  1. Remove the engine assembly w/ transmission out of the vehicle slowly and carefully.



52. REMOVE STARTER ASSEMBLY


    A102709E01
  1. Remove the 2 bolts, then remove the ground cable and bracket.



    A113538E02
  1. Remove the nut and disconnect the wire harness from terminal 30.

  1. Disconnect the terminal 50 connector from the starter assembly.

  1. Remove the 2 bolts and the starter assembly.



53. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
(Click here)


54. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)


55. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)


    C114267E01
  1. Put matchmarks on the clutch cover assembly and the flywheel sub-assembly.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the set bolts, and pull off the clutch cover assembly.

    NOTICE:
    Do not drop the clutch disc assembly.



56. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

NOTICE:
Keep the lining part of the clutch disc assembly, the pressure plate and surface of the flywheel sub-assembly away from oil and foreign matter.



57. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)


    A102137E01
  1. Fix the crankshaft with SST.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A109815E02
  1. Remove the 10 bolts and flywheel.



58. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)


    A102137E01
  1. Fix the crankshaft with SST.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A102156E01
  1. Remove the 10 bolts, spacer RR, drive plate and spacer FR.



59. REMOVE REAR END PLATE
  1. Remove the 2 bolts and rear end plate.



60. INSTALL ENGINE HANGERS


    G037564E02
  1. Install the engine hangers with the bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 30 ft.*lbf }

    Part name
    Part No.
    Engine hangers
    12281-75040
    Bolt
    91552-A1020

    NOTICE:
    Use new bolts for the engine hangers.



61. REMOVE FRONT SUSPENSION CROSS MEMBER SUB-ASSEMBLY
  1. Hold the engine with the engine sling device and chain block.

  1. Remove the 4 bolts from the engine mounting insulator.

  1. Remove the engine assembly by operating the engine sling device and chain block.



62. INSTALL ENGINE STAND


63. REMOVE ENGINE WIRE
  1. Remove the engine wire from the engine assembly.



64. REMOVE VENTILATION PIPE
  1. Remove the bolt and ventilation pipe.



65. REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY


    A102438E01
  1. Disconnect the throttle motor connector.(A)

  1. Disconnect the water by-pass hose.(B)

  1. Disconnect the water by-pass hose No.2.(C)

  1. Remove the 2 bolts and 2 nuts, then remove the throttle body assembly.(D)



    G037700
  1. Remove the gasket from the intake manifold.



66. REMOVE INTAKE MANIFOLD
  1. Disconnect the ventilation hose No.3.



    A102806E01
  1. Remove the 5 bolts, 2 nuts, intake manifold and gasket.



67. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the bolts and ignition coil assembly.



68. REMOVE SPARK PLUG


69. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

NOTICE:
Be careful not to drop the injectors when removing the delivery pipe.



    A087156
  1. Disconnect the fuel hoses.

  1. Disconnect the 4 injector connectors.

  1. Remove the 2 bolts O-ring and fuel pulsation damper assembly.

  1. Remove the 2 bolts and delivery pipe together with the 4 injectors.

  1. Remove the delivery pipe spacers.



    A087158
  1. Using a screwdriver, pry out the 4 spacers from the cylinder head.



70. REMOVE INJECTOR ASSEMBLY


    A087157E01
  1. Pull out the 4 injectors from the delivery pipe.

  1. Remove the O-rings from the injectors.



71. REMOVE EXHAUST MANIFOLD HEAT INSULATOR NO.1
  1. Remove the 4 bolts and heat insulator.



72. REMOVE AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection Ststem)


    A102809
  1. Remove the 4 nuts and intake pipe No.4 and gaskets.



    A102810
  1. Disconnect the air switching valve connector.

  1. Remove the 2 nuts and air switching valve.



73. REMOVE EXHAUST MANIFOLD


    A112543E02
  1. w/o Secondary air injection system:

    1. Remove the 6 nuts, exhaust manifold and gasket.

  1. w/ Secondary air injection system:

    1. Remove the 8 nuts, exhaust manifold and gasket.



74. REMOVE FAN PULLEY
  1. Remove the 4 nuts, fan pulley and fan spacer.



75. REMOVE WATER BY-PASS PIPE NO.1
  1. Remove the bolt, 2 nuts, water by-pass pipe and gasket.



76. REMOVE WATER INLET


    A087301
  1. Remove the 2 nuts, bolt, water inlet and gasket.



77. REMOVE THERMOSTAT


    A086841J01
  1. Remove the thermostat.



78. REMOVE GENERATOR ASSEMBLY


    A088507
  1. Disconnect the generator connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Remove the 3 bolts and generator assembly.



79. REMOVE COMPRESSOR MOUNTING BRACKET NO.1 (w/ Air Conditioning)


    A109816
  1. Remove the 5 bolts and compressor mounting bracket.



80. REMOVE IDLER PULLEY SUB-ASSEMBLY NO.1


    A102170
  1. Remove the bolt, pulley plate, collar, and idler pulley sub-assembly No.1.



81. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A102171
  1. Remove the 3 bolts and belt tensioner.



82. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY


    A102133
  1. Using a 24 mm deep socket wrench, remove the oil pressure switch.



83. REMOVE KNOCK CONTROL SENSOR


    G037712E01
  1. Disconnect the knock control sensor connector.

  1. Remove the bolt and the knock control sensor.



84. REMOVE WATER TEMPERATURE SENSOR


    A102134
  1. Using a 19 mm deep socket wrench, remove the water temperature sensor.



85. REMOVE ENGINE MOUNTING BRACKET FRONT NO.1 RH


    A102168
  1. Remove the 4 bolts and mounting bracket.



86. REMOVE ENGINE MOUNTING BRACKET FRONT NO.1 LH


    A102169
  1. Remove the 4 bolts and mounting bracket.



87. REMOVE ENGINE OIL LEVEL SENSOR
  1. Remove the 4 bolts and engine oil level sensor.