ECD SYSTEM > Black Smoke Emitted |
| 1.CHECK OUTPUT DTC (RELATED TO ENGINE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: Power train / ECD / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| DTCs related to the engine (Click here) | B |
|
| ||||
| A | |
| 2.READ VALUE OF INJECTOR ASSEMBLY (INJECTION VOLUME AND INJECTION FEED BACK VAL #1 TO #4) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the intelligent tester ON.
Enter the following menus: Power train / ECD / Data List.
Select the following menu items in order and read the values.
| Item | Engine Speed* | Reference Value |
| Injection Volume | Idling (No engine load) | 3 to 10 mm3
|
| Injection Feedback Val #1 | Idling (No engine load) | -3.0 to 3.0 mm3
|
| Injection Feedback Val #2 | Idling (No engine load) | -3.0 to 3.0 mm3
|
| Injection Feedback Val #3 | Idling (No engine load) | -3.0 to 3.0 mm3
|
| Injection Feedback Val #4 | Idling (No engine load) | -3.0 to 3.0 mm3
|
|
| ||||
| OK | |
| 3.PERFORM ENGINE RPM ACCELERATION |
Accelerate the engine speed to the maximum rpm with no load 20 times.
Check the volume of black smoke in the exhaust gas.
| Result | Proceed to |
| Black smoke is not present | OK |
| Black smoke remains in the exhaust gas | NG |
|
| ||||
| NG | |
| 4.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM |
Remove the air cleaner filter.
Inspect the EGR valve operation.
Start the engine and warm it up.
When the engine is idling and the vacuum hose is disconnected from the EGR valve, check that clicking sounds are emitted from the EGR valve.
Inspect the throttle valve operation.
Start the engine.
Check if the throttle valve fully opens when accelerating the engine speed.
|
| ||||
| OK | |
| 5.CHECK ECM TERMINAL VOLTAGE (EGLS TERMINAL) |
![]() |
Turn the ignition switch ON.
Measure the voltage of the ECM connector.
| Tester Connection | Condition | Specified Condition |
| D3-33 (EGLS) - D1-28 (E2) | Ignition Switch ON | 0.3 to 1.3 V |
Turn the ignition switch ON.
Engine start.
Measure the voltage of the ECM connector.
| Tester Connection | Condition | Specified Condition |
| D3-33 (EGLS) - D1-28 (E2) | Idling: 750 rpm | 2.21 to 4.0 V |
|
| ||||
| OK | |
| 6.CHECK TURBOCHARGING PRESSURE |
Check the turbocharger pressure. (Click here)
|
| ||||
| OK | |
| 7.PERFORM ACTIVE TEST BY FUEL PRESSURE SENSOR AND INJECTOR ASSEMBLY |
Connect the intelligent tester to the DLC3.
Start the engine and turn the intelligent tester ON.
Enter the following menus: Power train / ECD / Data List.
Select the following menu items in order and read the values.
| Item | Engine Speed* | Reference Value |
| Fuel Pressure | Idling | 25 to 35 MPa |
| Fuel Pressure | 2,000 rpm (no engine load) | 25 to 35 MPa |
| Fuel Pressure | 3,000 rpm (no engine load) | 35 to 45 MPa |
| Injection Volume | Idling | 3 to 10 mm3
|
| Injection Volume | 2,000 rpm (no engine load) | 3 to 10 mm3
|
| Injection Volume | 3,000 rpm (no engine load) | 4 to 12 mm3
|
| Main Injection | Idling | 525 to 675 μs |
| Pilot 2 Injection | Idling | 350 to 450 μs |
| Injection Feedback Val #1 | Idling | -3.0 to 3.0 mm3
|
| Injection Feedback Val #2 | Idling | -3.0 to 3.0 mm3
|
| Injection Feedback Val #3 | Idling | -3.0 to 3.0 mm3
|
| Injection Feedback Val #4 | Idling | -3.0 to 3.0 mm3
|
| Result | Proceed to |
| Within reference value | A |
| One of Injection Feedback Val #1 to #4 is not within reference value | B |
| Other result | C |
|
| ||||
|
| ||||
| A | |
| 8.INSPECT CYLINDER COMPRESSION PRESSURE |
Check the cylinder compression pressure. (Click here)
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - EDU) |
![]() |
Disconnect the D24, D25, D26 and D27 injector connectors.
Disconnect the B13 EDU connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| D24-1 - B13-4 (INJ1) | Below 1 Ω |
| D25-1 - B13-2 (INJ2) | Below 1 Ω |
| D26-1 - B13-1 (INJ3) | Below 1 Ω |
| D27-1 - B13-3 (INJ4) | Below 1 Ω |
| D24-2 - B13-5 (COM1) | Below 1 Ω |
| D25-2 - B13-6 (COM2) | Below 1 Ω |
| D26-2 - B13-6 (COM2) | Below 1 Ω |
| D27-2 - B13-5 (COM1) | Below 1 Ω |
| D24-1 or B13-4 (INJ1) - Body ground | 10 kΩ or higher |
| D25-1 or B13-2 (INJ2) - Body ground | 10 kΩ or higher |
| D26-1 or B13-1 (INJ3) - Body ground | 10 kΩ or higher |
| D27-1 or B13-3 (INJ4) - Body ground | 10 kΩ or higher |
| D24-2 or B13-5 (COM1) - Body ground | 10 kΩ or higher |
| D25-2 or B13-6 (COM2) - Body ground | 10 kΩ or higher |
| D26-2 or B13-6 (COM2) - Body ground | 10 kΩ or higher |
| D27-2 or B13-5 (COM1) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (CONTROL THE CYLINDER FUEL CUT) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the intelligent tester ON.
Enter the following menus: Power train / ECD / Active Test / Control the Cylinder #1, #2, #3 and #4 Fuel Cut.
Check the engine idling condition while the fuel injection of each cylinder is cut using the intelligent tester.
| Engine Idling Condition | Proceed To |
| Becomes unstable | A |
| Does not change | B |
|
| ||||
| A | ||
| ||
| 11.CHECK AND REPLACE ECM TERMINAL VOLTAGE (THW TERMINAL) |
![]() |
Start the engine.
Measure the voltage of the ECM connector.
| Tester Connection | Condition | Specified Condition |
| D1-19 (THW) - D1-28 (E2) | Idling, engine coolant temperature between 60 and 120°C (140 and 248°F) | 0.2 to 1.0 V |
|
| ||||
| OK | |
| 12.CHECK ECM TERMINAL VOLTAGE (PIM TERMINAL) |
![]() |
Turn the ignition switch ON.
Measure the voltage of the ECM connectors.
| Tester Connection | Condition | Specified Condition |
| D3-28 (PIM) - D1-28 (E2) | Applied negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) | 1.3 to 1.9 V |
| D3-28 (PIM) - D1-28 (E2) | Same as atmospheric pressure | 2.4 to 3.1 V |
| D3-28 (PIM) - D1-28 (E2) | Applied positive pressure of 170 kPa (1,275 mmHg, 50.2 in.Hg) | 3.7 to 4.3 V |
|
| ||||
| OK | |
| 13.CHECK ECM TERMINAL VOLTAGE (NE+ AND NE- TERMINALS) |
![]() |
While idling the engine, check the waveform of the ECM connector using an oscilloscope.
| Tester Connection | Specified Condition |
| D1-27 (NE+) - D1-34 (NE-) | Correct waveform is shown |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
|
| ||||
| OK | |
| 14.CHECK ECM TERMINAL VOLTAGE (VPA AND VPA2 TERMINALS) |
![]() |
Turn the ignition switch ON.
Measure the voltage of the ECM connector.
| Tester Condition | Accelerator Pedal Condition | Specified Condition |
| B9-22 (VPA) - B9-28 (EPA) | Released | 0.6 to 1.0 V |
| B9-22 (VPA) - B9-28 (EPA) | Depressed | 2.9 to 4.2 V |
| B9-23 (VPA2) - B9-29 (EPA2) | Released | 1.4 to 1.8 V |
| B9-23 (VPA2) - B9-29 (EPA2) | Depressed | 3.7 to 5.0 V |
|
| ||||
| OK | |
| 15.CHECK ECM TERMINAL VOLTAGE (THA TERMINAL) |
![]() |
Start the engine.
Measure the voltage of the ECM connector.
| Tester Connection | Condition | Specified Condition |
| D1-31 (THA) - D1-28 (E2) | Idling, intake air temperature at 20°C (68°F) | 0.5 to 3.4 V |
|
| ||||
| OK | |
| 16.CHECK ECM TERMINAL VOLTAGE (PCR1 TERMINAL) |
![]() |
Start the engine.
Measure the voltage of the ECM connector.
| Tester Connection | Condition | Specified Condition |
| D1-26 (PCR1) - D1-28 (E2) | Idling | 1.3 to 1.8 V |
|
| ||||
| OK | ||
| ||
| 17.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
![]() |
Remove the sensor.
Measure the resistance of the sensor.
| Connection | Specified Condition |
| 20°C (68°F) | 2.32 to 2.59 kΩ |
| 80°C (176°F) | 0.310 to 0.326 kΩ |
|
| ||||
| OK | ||
| ||
| 18.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM) |
![]() |
Disconnect the D51 sensor connector.
Disconnect the D3 and D1 ECM connectors.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| D51-2 (PIM) - D3-28 (PIM) | Below 1 Ω |
| D51-3 (VC) - D1-18 (VC) | Below 1 Ω |
| D51-1 (E2) - D1-28 (E2) | Below 1 Ω |
| D51-2 (PIM) or D3-28 (PIM) - Body ground | 10 kΩ or higher |
| D51-3 (VC) or D1-18 (VC) - Body ground | 10 kΩ or higher |
| D51-1 (E2) or D1-28 (E2) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 19.INSPECT CRANKSHAFT POSITION SENSOR |
![]() |
Disconnect the D17 sensor connector.
Measure the resistance of the sensor.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Cold | 1,630 to 2,740 Ω |
| 1 - 2 | Hot | 2,065 to 3,225 Ω |
|
| ||||
| OK | ||
| ||
| 20.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the B1 sensor connector.
Disconnect the B9 ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| B1-1 (VCP2) - B9-27 (VCP2) | Below 1 Ω |
| B1-2 (EPA2) - B9-29 (EPA2) | Below 1 Ω |
| B1-3 (VPA2) - B9-23 (VPA2) | Below 1 Ω |
| B1-4 (VCP1) - B9-20 (VCPA) | Below 1 Ω |
| B1-5 (EP1) - B9-28 (EPA) | Below 1 Ω |
| B1-6 (VPA1) - B9-22 (VPA) | Below 1 Ω |
| B1-1 (VCP2) or B9-27 (VCP2) - Body ground | 10 kΩ or higher |
| B1-2 (EPA2) or B9-29 (EP2) - Body ground | 10 kΩ or higher |
| B1-3 (VPA2) or B9-23 (VPA2) - Body ground | 10 kΩ or higher |
| B1-4 (VCP1) or B9-26 (VCPA) - Body ground | 10 kΩ or higher |
| B1-5 (EP1) or B9-28 (EPA) - Body ground | 10 kΩ or higher |
| B1-6 (VPA1) or B9-22 (VPA) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 21.INSPECT INTAKE AIR TEMPERATURE SENSOR |
![]() |
Remove the sensor.
Measure the resistance of the sensor.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 2.21 to 2.69 kΩ |
|
| ||||
| OK | ||
| ||
| 22.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR) |
![]() |
Disconnect the D45 sensor connector.
Measure the resistance of the sensor.
| Tester Connection | Specified Condition |
| D45-1 (E2) - D45-2 (PR) | 3 kΩ or less |
| D45-2 (PR) - D45-3 (VC) | 16.4 kΩ or less |
|
| ||||
| OK | |
| 23.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM) |
![]() |
Disconnect the D1 ECM connector.
Disconnect the D45 sensor connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| D1-26 (PCR1) - D45-2 (PR) | Below 1 Ω |
| D1-18 (VC) - D45-3 (VCC) | Below 1 Ω |
| D1-28 (E2) - D45-1 (E2) | Below 1 Ω |
| D1-26 (PCR1) or D45-2 (PR) - Body ground | 10 kΩ or higher |
| D1-18 (VC) or D45-3 (VC) - Body ground | 10 kΩ or higher |
| D1-28 (E2) or D45-1 (E2) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 24.REPLACE ECM |
Check the volume of black smoke in the exhaust gas.
|
| ||||
| OK | ||
| ||