2014-2019 Hiace · Service Manual CRUISE CONTROL SYSTEM

P0571 Stop Light Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Dec 2017

Versions by build date: Oct 2014 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. Upon receiving the signal, the ECM cancels cruise control. Even if there is a malfunction in the stop light signal circuit while cruise control is in operation, normal driving is maintained due to a fail-safe function.
When the brake pedal is depressed, positive voltage is applied to terminal STP of the ECM through the STOP fuse and stop light switch, and the ECM cancels cruise control.
DTC Code
DTC Detection Condition
Trouble Area
P0571
The voltages of terminals ST1- and STP of the ECM are both below 1 V for 0.5 seconds or more.
  1. Stop light switch circuit
  2. Stop light switch assembly
  3. ECM

WIRING DIAGRAM

E290481E03
E290481E04

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

  1. E290482E01
    Disconnect the stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B2-2 - Body ground
    Always
    11 to 14 V
    B2-4 - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Remove the stop light switch assembly.

  1. Inspect the stop light assembly (Click here).



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
  1. Disconnect the B2 stop light switch assembly connector.

  1. Disconnect the B72*1 or B71*2 ECM connector.

    1. *1: for 1KD-FTV
    2. *2: for 2TR-FE

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    B2-3 - B72-34 (ST1-)
    Always
    Below 1 Ω
    B2-1 - B72-35 (STP)
    B2-3 - Body ground
    Always
    10 kΩ or higher
    B2-1 - Body ground
    for 2TR-FE 
    Tester Connection
    Condition
    Specified Condition
    B2-3 - B71-35 (ST1-)
    Always
    Below 1 Ω
    B2-1 - B71-36 (STP)
    B2-3 - Body ground
    Always
    10 kΩ or higher
    B2-1 - Body ground

Result 
Result
Proceed to
OK (for 1KD-FTV)
A
OK (for 2TR-FE)
B
NG
C


B
REPLACE ECM (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ECM (Click here)


← P0571 Stop Light Switch Circuit Malfunction (Jan 2017 – Nov 2017)P0575 Cruise Control Input Circuit (Oct 2014 – Dec 2014) →