INSTALLATION
Removal / installation · Vehicles built from Dec 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
| 1. INSTALL WIRE HARNESS CLAMP BRACKET |
Install the wire harness clamp bracket.

- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 2. INSTALL TRANSMISSION CONTROL CABLE BRACKET NO.1 |
Install the transmission control cable bracket No.1 with the 2 bolts.
- Torque:
- 28 N*m{ 286 kgf*cm , 21 ft.*lbf }
| 3. INSTALL REAR ENGINE MOUNTING INSULATOR ASSEMBLY |
Install the rear engine mounting insulator assembly with the 4 bolts.

- Torque:
- 18 N*m{ 178 kgf*cm , 13 ft.*lbf }
| 4. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY |
Install the transmission unit assembly with the 8 bolts.

- Torque:
- Bolt A:
- 72 N*m{ 729 kgf*cm , 53 ft.*lbf }
- Bolt B:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
Install the transmission unit assembly to the frame with the bolt, nut, and 2 washers.

- Torque:
- 98 N*m{ 999 kgf*cm , 72 ft.*lbf }
- NOTICE:
- Insert the bolt from the left side of the vehicle.
- Tighten the nut while holding the bolt.
- Insert the bolt from the left side of the vehicle.
| 5. INSTALL STARTER ASSEMBLY (for 1.7 kW Type) |
Install the starter assembly with the 2 bolts.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
Connect the starter wire and install the nut.
- Torque:
- 9.8 N*m{ 100 kgf*cm , 87 in.*lbf }
Connect the starter connector.
Close the terminal cap.
Connect the ground cable and wiring harness clamp bracket with the 2 bolts.
- Torque:
- 25 N*m{ 251 kgf*cm , 18 ft.*lbf }
| 6. INSTALL STARTER ASSEMBLY (for 1.6 kW Type) |
Install the starter with the 2 bolts.

- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
Connect the wire harness to terminal 30 and install the nut.
- Torque:
- 9.8 N*m{ 100 kgf*cm , 87 in.*lbf }
Connect the terminal 50 connector to the starter assembly.
Install the ground cable and wire bracket with the 2 bolts.

- Torque:
- 25 N*m{ 251 kgf*cm , 18 ft.*lbf }
| 7. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY |
Install the clutch release cylinder with the 2 bolts.

- Torque:
- 12 N*m{ 120 kgf*cm , 9 ft.*lbf }
| 8. INSTALL WIRE HARNESS |
Connect the 2 connectors and clamps.

| 9. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY |
Install 2 new clips to the transmission control cable bracket No.1.

Install the transmission control cable assembly to the transmission control cable bracket No.1.
- NOTICE:
- Be sure that A claws of the clips are firmly engaged into the bracket grooves.
- Be sure the cable is set in the clip with both B claws erected to prevent slippage of the cable in the opposite direction.
- Be sure that A claws of the clips are firmly engaged into the bracket grooves.
Align the matchmarks on the control cable assembly and the outer lever.

Install the transmission control cable assembly to the outer levers with the 2 nuts.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 10. INSTALL PROPELLER SHAFT ASSEMBLY (for Long Wheelbase) |
Remove the SST from the extension housing.

Install the propeller shaft assembly in the extension housing.
Align the matchmarks on the propeller shaft flange and differential flange.
Install the propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.

- Torque:
- 74 N*m{ 755 kgf*cm , 54 ft.*lbf }
| 11. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Super Long Wheelbase) |
Remove the SST from the extension housing.

Install the propeller with center bearing shaft assembly in the extension housing.
Install the center support bearing assembly No.1, and temporarily tighten the 2 bolts.

Align the matchmarks on the propeller shaft flange and differential flange.

Install the propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.
- Torque:
- 74 N*m{ 755 kgf*cm , 54 ft.*lbf }
Check that the center line of the bracket is at right angles to the shaft axial direction.

Adjust the center support bearing assembly No.1.

- HINT:
- With the vehicle unladen, adjust the center support bearing No.1 to maintain the angles, as shown.
- In the same conditions, check the center line in the axial direction. Adjust the bearing if necessary.
- The center bearing center line and center bearing housing center line must be adjusted to within -1.0 to 1.0 mm (-0.0394 to 0.0394 in.) of each other in the vehicle's longitudinal direction with the vehicle unladen.
- With the vehicle unladen, adjust the center support bearing No.1 to maintain the angles, as shown.
Tighten the 2 bolts.
- Torque:
- 36 N*m{ 369 kgf*cm , 27 ft.*lbf }
| 12. INSTALL EXHAUST PIPE ASSEMBLY FRONT (for Long Wheelbase) |
w/ Secondary air injection system:
Install the fuel ratio sensor. (Click here)
- Torque:
- 44 N*m{ 449 kgf*cm , 32 ft.*lbf }
For unleaded gasoline engine:
Install the oxygen sensor. (Click here)
- Torque:
- 44 N*m{ 449 kgf*cm , 32 ft.*lbf }
Inspect the compression spring.
Using vernier calipers, measure the free length of the compression springs.

- Minimum length:
- 40.5mm(1.594 in.)
- HINT:
- If the free length is less than the minimum, replace the compression spring.
Install the gasket.

Fully insert a new gasket to the exhaust manifold by hand.
Using a wooden block, uniformly strike the gasket so that the gasket and exhaust manifold are properly fit.
- NOTICE:
- Be careful with the installation direction of the gasket.
- Do not reuse the gasket.
- Do not damage the gasket.
- To ensure a proper seal, do not use the exhaust pipe assembly front to force the gasket onto the exhaust manifold.
- Be careful with the installation direction of the gasket.
Install a new gasket to the exhaust pipe assembly front.
Connect the exhaust pipe assembly front to the exhaust pipe support.
Install the exhaust pipe assembly front with the 4 bolts, 2 nuts, and 2 compression springs.
- Torque:
- Exhaust manifold side:
- 43 N*m{ 438 kgf*cm , 32 ft.*lbf }
- Torque:
- Exhaust pipe assembly tail side:
- 48 N*m{ 489 kgf*cm , 35 ft.*lbf }
- NOTICE:
- After installation, check that the clearance is almost the same at any point between the flanges of the exhaust manifold and exhaust pipe assembly front.
For unleaded gasoline engine:
Connect the sensor connector(s).
| 13. INSTALL EXHAUST PIPE ASSEMBLY FRONT (for Super Long Wheelbase) |
w/ Secondary air injection system:
Install the air fuel ratio sensor. (Click here)
- Torque:
- 44 N*m{ 449 kgf*cm , 32 ft.*lbf }
For Unleaded gasoline engine:
Install the oxygen sensor. (Click here)
- Torque:
- 44 N*m{ 449 kgf*cm , 32 ft.*lbf }
Inspect the compression spring.
Using vernier calipers, measure the free length of the compression springs.

- Minimum length:
- 40.5 mm (1.594 in.)
- HINT:
- If the free length is less than the minimum, replace the compression spring.
Install the gasket.

Fully insert a new gasket to the exhaust manifold by hand.
Using a wooden block, uniformly strike the gasket so that the gasket and exhaust manifold are properly fit.
- NOTICE:
- Be careful with the installation direction of the gasket.
- Do not reuse the gasket.
- Do not damage the gasket.
- To ensure a proper seal, do not use the exhaust pipe assembly front to force the gasket onto the exhaust manifold.
- Be careful with the installation direction of the gasket.
Install a new gasket to the exhaust pipe assembly front.
Connect the exhaust pipe assembly front to the exhaust pipe support.
Install the exhaust pipe assembly front with the 4 bolts, 2 nuts, and 2 compression springs.
- Torque:
- Exhaust manifold side:
- 43 N*m{ 438 kgf*cm , 32 ft.*lbf }
- Exhaust pipe assembly center side:
- 48 N*m{ 489 kgf*cm , 35 ft.*lbf }
- NOTICE:
- After installation, check that the clearance is almost the same at any point between the flanges of the exhaust manifold and exhaust pipe assembly front.
For Unleaded gasoline engine:
Connect the sensor connector(s).
| 14. ADD MANUAL TRANSMISSION OIL |
Park the vehicle in a level place.

Remove the transmission filler plug and gasket.
Check that the oil surface is within 5 mm (0.20 in.) below the lowest point of the transmission filler plug opening.
- Oil grade:
- TOYOTA Genuine Manual Transmission Gear oil API GL-3 (GL-4) or equivalent
- Viscosity:
- Above -10°C (14°F): SAE 75W-90, 80W or 80W-90
- Below -10°C (14°F): SAE 75W-90
- Capacity:
- 2.6 liters (2.7 US qts, 2.3 Imp. qts)
- NOTICE:
- Problems may occur when the oil level is too high or too low.
- After replacing the oil, drive the vehicle and check the oil level again.
- Problems may occur when the oil level is too high or too low.
Check for oil leakage if the oil level is low.
Install the transmission filler plug and a new gasket.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 16. CHECK FOR EXHAUST GAS LEAKS |
| 17. PERFORM INITIALIZATION |
