B2784 Antenna Coil Open / Short
Diagnostic trouble codes · Vehicles built from Dec 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
When an open or short circuit is detected in the antenna coil built into the transponder key coil, the transponder key ECU assembly stores this DTC.| DTC No. |
DTC Detection Condition |
Trouble Area |
DTC Output Confirmation Operation |
| B2784 |
The antenna coil in the transponder key coil is open/shorted. |
|
Insert the key into the ignition key cylinder. |
| Vehicle Condition when Malfunction Detected |
Fail-safe Operation when Malfunction Detected |
| Engine cannot be started |
- |
| DTC No. |
Data List and Active Test |
| B2784 |
Antenna Coil Status |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- If the transponder key ECU assembly is replaced, refer to Service Bulletin.
- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
- When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- If the transponder key ECU assembly is replaced, refer to Service Bulletin.
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
- HINT:
- Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
- OK:
- DTC B2784 is not output.
|
|
||||
| OK | ||
| ||
| 3. CHECK CONNECTION OF CONNECTOR |
Check that the connectors are properly connected to the transponder key coil.
| NEXT | |
| 4. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 5. CHECK FOR DTC |
Check for DTCs (Click here).
- HINT:
- Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
- OK:
- DTC B2784 is not output.
|
|
||||
| OK | ||
| ||
| 6. CHECK TRANSPONDER KEY COIL (OUTPUT) |
Using an oscilloscope, check the waveform.


Text in Illustration *a
Component with harness connected
(Transponder Key Coil)
*b
Waveform 1
*c
Waveform 2
-
-
Waveform 1 Item
Content
Tester Connection
H79-1 (ANT1) - Body ground
Tool Setting
2 V/DIV., 500 ms/DIV
Condition
Within 3 seconds of inserting key into ignition key cylinder
Waveform 2 Item
Content
Tester Connection
F79-5 (ANT2) - Body ground
Tool Setting
2 V/DIV., 500 ms/DIV
Tool Setting
Within 3 seconds of inserting key into ignition key cylinder
- OK:
- Waveform is similar to that shown in the illustration.
|
|
||||
| OK | |
| 7. REPLACE TRANSPONDER KEY ECU ASSEMBLY |
Replace the transponder key ECU assembly with a new one.
- HINT:
- Refer to Service Bulletin.
- NOTICE:
- Key ID code registration is necessary when replacing the transponder key ECU assembly.
- Refer to Service Bulletin.
| NEXT | |
| 8. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 9. CHECK FOR DTC |
Check for DTCs (Click here).
- HINT:
- Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
- OK:
- DTC B2784 is not output.
|
|
||||
| OK | ||
| ||
| 10. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY COIL) |
Disconnect the H60 transponder key ECU assembly connector.
Disconnect the H79 transponder key coil connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H60-4 (ANT1) - H79-1 (ANT1)
Always
Below 1 Ω
H60-15 (ANT2) - H79-5 (ANT2)
Always
Below 1 Ω
H60-4 (ANT1) - Body ground
Always
10 kΩ or higher
H79-1 (ANT1) - Body ground
Always
10 kΩ or higher
H60-15 (ANT2) - Body ground
Always
10 kΩ or higher
H79-5 (ANT2) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 11. REPLACE TRANSPONDER KEY ECU ASSEMBLY |
Replace the transponder key ECU assembly with a new one.
- HINT:
- Refer to Service Bulletin.
- NOTICE:
- Key ID code registration is necessary when replacing the transponder key ECU assembly.
- Refer to Service Bulletin.
| NEXT | |
| 12. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 13. CHECK FOR DTC |
Check for DTCs (Click here).
- HINT:
- Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
- OK:
- DTC B2784 is not output.
|
|
||||
| OK | ||
| ||
