2014-2019 Hiace · Service Manual SECURITIES

B2784 Antenna Coil Open / Short

Diagnostic trouble codes · Vehicles built Jan 2015 – Dec 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

When an open or short circuit is detected in the antenna coil built into the transponder key coil, the transponder key ECU assembly stores this DTC.
DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2784
The antenna coil in the transponder key coil is open/shorted.
  1. Harness or connector
  2. Transponder key coil
  3. Transponder key ECU assembly
Insert the key into the ignition key cylinder.
Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started
-
Related Data List and Active Test 
DTC No.
Data List and Active Test
B2784
Antenna Coil Status

WIRING DIAGRAM

B329324E02

INSPECTION PROCEDURE

NOTICE:
  1. If the transponder key ECU assembly is replaced, refer to Service Bulletin.
  2. After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
  3. When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2784 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK CONNECTION OF CONNECTOR
  1. Check that the connectors are properly connected to the transponder key coil.


NEXT


4. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


5. CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2784 is not output.



NG
Go to step 6
OK

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

6. CHECK TRANSPONDER KEY COIL (OUTPUT)

  1. Using an oscilloscope, check the waveform.B329326E03

    Text in Illustration 
    *a
    Component with harness connected
    (Transponder Key Coil)
    *b
    Waveform 1
    *c
    Waveform 2
    -
    -
    Waveform 1 
    Item
    Content
    Tester Connection
    H79-1 (ANT1) - Body ground
    Tool Setting
    2 V/DIV., 500 ms/DIV
    Condition
    Within 3 seconds of inserting key into ignition key cylinder
    Waveform 2 
    Item
    Content
    Tester Connection
    F79-5 (ANT2) - Body ground
    Tool Setting
    2 V/DIV., 500 ms/DIV
    Tool Setting
    Within 3 seconds of inserting key into ignition key cylinder

    OK:
    Waveform is similar to that shown in the illustration.



NG
Go to step 10
OK


7. REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Replace the transponder key ECU assembly with a new one.

    HINT:
    Refer to Service Bulletin.

    NOTICE:
    Key ID code registration is necessary when replacing the transponder key ECU assembly.
    Refer to Service Bulletin.


NEXT


8. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


9. CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2784 is not output.



NG
REPLACE TRANSPONDER KEY COIL (Click here)
OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

10. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY COIL)
  1. Disconnect the H60 transponder key ECU assembly connector.

  1. Disconnect the H79 transponder key coil connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H60-4 (ANT1) - H79-1 (ANT1)
    Always
    Below 1 Ω
    H60-15 (ANT2) - H79-5 (ANT2)
    Always
    Below 1 Ω
    H60-4 (ANT1) - Body ground
    Always
    10 kΩ or higher
    H79-1 (ANT1) - Body ground
    Always
    10 kΩ or higher
    H60-15 (ANT2) - Body ground
    Always
    10 kΩ or higher
    H79-5 (ANT2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Replace the transponder key ECU assembly with a new one.

    HINT:
    Refer to Service Bulletin.

    NOTICE:
    Key ID code registration is necessary when replacing the transponder key ECU assembly.
    Refer to Service Bulletin.


NEXT


12. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


13. CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2784 is not output.



NG
REPLACE TRANSPONDER KEY COIL (Click here)
OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)


← B2784 Antenna Coil Open / Short (Oct 2014 – Dec 2014)B2784 Antenna Coil Open / Short (Jan 2017 – Nov 2017) →