All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate
Circuit diagnosis · Vehicles built from Dec 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the certification ECU (smart key ECU assembly); or 2) the electrical key transmitter sub-assembly. If the entry lock and wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the smart entry and wireless function.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN).
While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- Check that there are no electrical key transmitter sub-assemblies in the vehicle.
- Before performing the inspection, check that DTC B1242 (wireless door lock control) or DTC B27B0 is not output.
- Inspect the fuses for circuits related to this system before performing the following procedure.
- Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (Click here).
- After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
- The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
| 1. INSPECT BATTERY VOLTAGE |
Measure the voltage of the vehicle battery.
- Standard voltage:
- 11 to 14 V
- HINT:
- It may be possible to tell whether the vehicle battery is discharged by operating the horn.
- If the voltage is below 11 V, recharge or replace the vehicle battery before proceeding.
| NEXT | |
| 2. CHECK FOR DTC |
Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.
Connect the GTS and check for DTCs (Click here).
- HINT:
- When using the GTS with the engine switch off to troubleshoot: Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.
- OK:
- DTC is not output.
|
|
||||
| OK | |
| 3. CHECK DOOR AJAR WARNING OPERATION |
When door unlock by entry lock or wireless door lock operation functions even though all doors are closed, check the door ajar warning operation (Click here).
Result Result
Proceed to
Door ajar warning does not operate.
A
Door ajar warning operates.
B
|
|
||||
| A | |
| 4. CHECK POWER DOOR LOCK CONTROL SYSTEM |
When the door control switch on the power window regulator master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation (Click here).
- OK:
- Door locks operate normally.
|
|
||||
| OK | |
| 5. CHECK KEY DIAGNOSTIC MODE |
Check the following antennas in key diagnostic mode (Click here).
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
- HINT:
- If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
Check the No. 1 indoor electrical key antenna assembly (front bumper RH):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly RH, check that the wireless door lock buzzer sounds.Text in Illustration *a
0.7 to 1 m (2.30 to 3.28 ft.)
Check the No. 1 indoor electrical key antenna assembly (front bumper LH):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly LH, check that the wireless door lock buzzer sounds.Text in Illustration *a
0.7 to 1 m (2.30 to 3.28 ft.)
Check the No. 2 indoor electrical key antenna assembly (front floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.Text in Illustration *a
Inspection Point
Check the No. 3 indoor electrical key antenna assembly (rear floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.Text in Illustration *a
Inspection Point
Check the electrical key antenna (back door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (back door), check that the wireless door lock buzzer sounds.Text in Illustration *a
0.7 to 1 m (2.30 to 3.28 ft.)
- OK:
- Wireless door lock buzzer sounds.
Result Result
Proceed to
Diagnostic mode inspections fail for both channels
A
Diagnostic mode inspections succeed for both channels
B
Diagnostic mode inspection succeeds for only one of the channels
C
|
|
||||
|
|
||||
| A | |
| 6. CHECK WAVE ENVIRONMENT |
Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.
- HINT:
- When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
- If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
- There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
- If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
- When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
- OK:
- Wireless and entry functions operate normally.
|
|
||||
| OK | |
| 7. CHECK TRANSMITTER BATTERY |
Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.
Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.
Result Result
Proceed to
Transmitter LED does not illuminate when switch is pressed and held
A
Transmitter LED illuminates 3 times or more when switch is pressed and held
B
Transmitter LED illuminates once or twice but not a third time
C
- HINT:
- The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less (Click here).
- Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly against the engine switch, depressing the brake pedal and pressing the engine switch.
- The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less (Click here).
|
|
||||
|
|
||||
| A | |
| 8. INSPECT TRANSMITTER BATTERY (VOLTAGE) |
Inspect the transmitter battery.
- NOTICE:
- When removing the transmitter battery, make sure not to touch the electronic circuit board, as static electricity may cause a malfunction to occur.
Measure the voltage of the transmitter battery (Click here).
|
|
||||
| OK | ||
| ||
| 9. CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY |
Check if there are any other registered electrical key transmitter sub-assemblies.
Result Result
Proceed to
There are no other registered electrical key transmitter subassemblies
A
There is another registered electrical key transmitter sub-assembly
B
|
|
||||
| A | |
| 10. ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY) |
Register a new electrical key transmitter sub-assembly.
- HINT:
- Refer to the Service Bulletin.
| NEXT | |
| 11. CHECK ENTRY DOOR LOCK OPERATION |
Using another registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.
- OK:
- Entry lock/unlock operate normally.
|
|
||||
| OK | ||
| ||
| 12. REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Replace the certification ECU (smart key ECU assembly) with a new one.
- HINT:
- Refer to the Service Bulletin.
| NEXT | |
| 13. CHECK WIRELESS DOOR LOCK CONTROL SYSTEM |
Check that the wireless door lock functions operate normally (Click here).
- OK:
- Wireless door lock functions operate normally.
|
|
||||
| OK | ||
| ||
| 14. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |


| *a |
Component with harness connected (Certification ECU [Smart Key ECU Assembly]) |
- |
- |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
Power Source Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Power Supply Condition
Power supply state / ST ON, All OFF, IG ON or ACC ON
ALL OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)
IG ON: Engine switch on (IG) (IG1 relay on)
ST ON: Sending engine start request signal
-
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B75-20 (IG1D) - Body ground
Engine switch off
Below 1 V
Engine switch on (ACC)
Below 1 V
Engine switch on (IG)
9 V or higher
B75-21 (ACCD) - Body ground
Engine switch off
Below 1 V
Engine switch on (ACC)
8.5 V or higher
Engine switch on (IG)
8.5 V or higher
- HINT:
- Using the GTS, measure the voltage while confirming the power source mode on the Data List.
|
|
||||
| OK | |
| 15. INSPECT IG1 RELAY |
|
|
||||
| OK | |
| 16. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - IG1 RELAY) |
|
|
||||
| OK | |
| 17. INSPECT NO. 2 INTEGRATION RELAY (IG2 RELAY) |
|
|
||||
| OK | |
| 18. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INTEGRATION RELAY) |
|
|
||||
| OK | |
| 19. INSPECT NO.2 INTEGRATION RELAY (ACC RELAY) |
|
|
||||
| OK | |
| 20. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INTEGRATION RELAY) |
|
|
||||
| OK | |
| 21. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - BATTERY AND BODY GROUND) |
Disconnect the certification ECU (smart key ECU assembly) connector.

Text in Illustration *a
Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B75-10 (E) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B75-1 (+B) - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 22. CHECK ENTRY DOOR LOCK OPERATION |
Connect the certification ECU (smart key ECU assembly) connector.
Check the entry lock/unlock operation.
- OK:
- Entry lock/unlock operate normally.
|
|
||||
| OK | ||
| ||
| 23. REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Replace the certification ECU (smart key ECU assembly) with a new one.
- HINT:
- Refer to the Service Bulletin.
| NEXT | |
| 24. CHECK WIRELESS DOOR LOCK CONTROL SYSTEM |
Check that the wireless door lock functions operate normally (Click here).
- OK:
- Wireless door lock functions operate normally.
|
|
||||
| OK | ||
| ||
| 25. CHECK WAVE ENVIRONMENT |
Bring the electrical key transmitter sub-assembly that was checked first near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode (Click here).
- HINT:
- When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
- If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
- There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
- If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
- When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
- OK:
- Wireless and entry functions operate normally.
|
|
||||
| OK | |
| 26. CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY |
Check if there are any other registered electrical key transmitter sub-assemblies.
Result Result
Proceed to
There are no other registered electrical key transmitter sub-assemblies
A
There is another registered electrical key transmitter sub-assembly
B
|
|
||||
| A | |
| 27. ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY) |
Register a new electrical key transmitter sub-assembly.
- HINT:
- Refer to the Service Bulletin.
| NEXT | |
| 28. CHECK WAVE ENVIRONMENT |
Bring another registered electrical key transmitter sub-assembly near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.
- HINT:
- When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
- If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
- There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
- If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
- When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
- OK:
- Wireless and entry functions operate normally.
|
|
||||
| OK | ||
| ||
| 29. REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Replace the certification ECU (smart key ECU assembly) with a new one.
- HINT:
- Refer to Service Bulletin.
| NEXT | |
| 30. CHECK WIRELESS DOOR LOCK CONTROL SYSTEM |
Check that the wireless door lock functions operate normally.
- OK:
- Wireless door lock functions operate normally.
|
|
||||
| OK | ||
| ||
