2014-2019 Hiace · Service Manual ENGINE

B2285 Steering Lock Position Signal Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Dec 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN communication do not match.

HINT:
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2285
The steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN communication (1-trip detection logic*) do not match.
  1. AM2 fuse
  2. Steering lock ECU (steering lock actuator assembly)
  3. Certification ECU (smart key ECU assembly)
  4. Wire harness or connector
Disconnect the cable from the negative (-) battery terminal, wait 30 seconds and then reconnect the cable to the negative (-) battery terminal. Wait 40 seconds or more with the engine switch off (with the steering wheel locked), and then turn the engine switch on (ACC) (with the steering unlocked) and wait 40 seconds or more.
  1. *: Only detected while a malfunction is present and the engine switch is on (IG)
Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
The engine cannot be started.
The ECU does not send an engine start request.
Related Data List and Active Test Items 
DTC
Data List Item
Active Test Item
B2285
Power Source Control
  1. Steering Unlock Switch
Entry&Start
  1. Power Supply Short
  2. Motor Driver Short
  3. Lock Bar Stuck Error
-

WIRING DIAGRAM

C278816E01

INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  2. The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
  3. Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly), refer to the smart entry and start system (for Start Function) precaution (Click here).
  4. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  5. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


1. CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    1. If the steering wheel cannot be locked or unlocked, the engine switch cannot be turned on (IG) and the engine cannot be started.
    2. If LIN communication is not available, the steering wheel cannot be locked or unlocked.

    OK:
    LIN communication system DTC B2785 is not output simultaneously.



NG
GO TO DTC B2785 (Click here)
OK


2. READ VALUE USING GTS (STEERING UNLOCK SWITCH)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. According to the display on the GTS, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Steering Unlock Switch
    State of steering unlock sensor signal output from steering lock actuator assembly/ON or OFF
    ON: Steering unlocked
    OFF: Steering locked
    1. When the shift lever is in P and the engine switch is off, if any door is opened then closed, the steering is locked.
    2. When the key is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks.
    3. The engine cannot be started when the steering unlock signal is off.

    Result:
    Result
    Proceed to
    Data List item does not change
    A
    Data List item changes
    B



B
REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (Click here)
A


3. CHECK HARNESS AND CONNECTOR (POWER SOURCE)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


4. CHECK HARNESS AND CONNECTOR (GROUND)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
  1. Reconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. C197722E82
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Positive (+) tester probe → H80-4 (SLP1)
    Negative (-) tester probe → Body ground
    Steering locked*
    10 kΩ or higher
    Steering unlocked*
    Below 1 Ω

    HINT:
    1. *: If any of the doors are opened then closed with the shift lever in P and the engine switch off, the steering wheel will be locked. If the engine switch is then turned on (ACC) or on (IG), the steering wheel will be unlocked.
    2. DTC B2285 may be stored due to a malfunction in the steering lock ECU (steering lock actuator assembly). The steering lock position signal and unlock position signal are sent from the steering lock ECU (steering lock actuator assembly) to the certification ECU (smart key ECU assembly) individually.

    Text in Illustration 
    *a
    Component with harness connected
    (Steering Lock ECU (Steering Lock Actuator Assembly))



NG
REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))
  1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the H80 steering lock ECU (steering lock actuator assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B75-22 (SLP) - H80-4 (SLP1)
    Always
    Below 1 Ω
    B75-22 (SLP) or H80-4 (SLP1) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


← B2285 Steering Lock Position Signal Circuit Malfunction (Jan 2017 – Nov 2017)B2286 Runnable Signal Malfunction (+ P0335) (Oct 2014 – Dec 2014) →