INSTALLATION
Removal / installation · Vehicles built Oct 2014 – Mar 2016
Versions by build date: Oct 2014 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
| 1. INSTALL REAR AXLE SHAFT OIL SEAL (w/ ABS) |
Using SST and a hammer, install a new rear axle shaft oil seal.

- SST
- 09554-22010
- Seal installation depth:
- 34.5 to 35.5 mm (1.358 to 1.398 in.)
- NOTICE:
- Do not drive the oil seal in deeper than the specified range or an oil leak will occur.
- Do not tilt the oil seal during installation.
- Do not drive the oil seal in deeper than the specified range or an oil leak will occur.
Text in Illustration *1
Rear Axle Housing Assembly
*2
Rear Axle Shaft Oil Seal
*a
Seal installation depth
Apply MP grease to the oil seal lip.
| 2. INSTALL REAR AXLE SHAFT OIL SEAL (w/o ABS) |
Using SST and a hammer, install a new rear axle shaft oil seal.

- SST
- 09554-22010
- Seal installation depth:
- 0.5 to 1.5 mm (0.0197 to 0.0590 in.)
- NOTICE:
- Do not drive the oil seal in deeper than the specified range or an oil leak will occur.
- Do not tilt the oil seal during installation.
- Do not drive the oil seal in deeper than the specified range or an oil leak will occur.
Text in Illustration *1
Rear Axle Housing Assembly
*2
Rear Axle Shaft Oil Seal
*a
Seal installation depth
Apply MP grease to the oil seal lip.
| 3. INSTALL BEARING RETAINER O-RING |
Apply MP grease to the bearing retainer O-ring.
Install the bearing retainer O-ring to the rear axle shaft housing.
| 4. INSTALL REAR AXLE SHAFT WITH BACKING PLATE |
Install the rear axle shaft with backing plate to the rear axle shaft housing with the 4 nuts.

- Torque:
- 65 N*m{ 663 kgf*cm , 48 ft.*lbf }
- NOTICE:
- Be careful not to damage the rear axle shaft oil seal.
- Be careful not to damage the skid control rotor rear.
- Be careful not to damage the rear axle shaft oil seal.
| 5. INSTALL REAR SPEED SENSOR (w/ ABS) |
Install the rear speed sensor LH with the bolt.


- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
- NOTICE:
- Prevent foreign matter from attaching to the sensor tip.
Attach the 4 clamps.
Connect the connector.
| 6. INSTALL REAR WHEEL BRAKE CYLINDER ASSEMBLY |
Install the wheel brake cylinder assembly with the 2 bolts.

- Torque:
- 9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
Using a union nut wrench, connect the brake tube.
- Torque:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
- NOTICE:
- Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).
| 7. APPLY HIGH TEMPERATURE GREASE |
Apply high temperature grease to the shoe attached surface of the backing plate.

Text in Illustration *1
High temperature grease
| 8. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.3 |
Install the parking brake cable assembly No.3 to the rear brake backing plate with the 2 bolts.

- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
| 9. INSTALL PARKING BRAKE SHOE STRUT SET |
Apply the high temperature grease to the adjusting bolt.

Text in Illustration *1
High temperature grease
Install the tension spring to the shoe strut set.
| 10. INSTALL REAR BRAKE SHOE |
for 254 mm drum:
Using pliers, install the rear brake shoe, shoe strut set, rear cushion lever and shoe lever with a new C-washer.

Text in Illustration *1
Brake Shoe Lever
*2
Brake Shoe Strut Set
*3
Rear Brake Shoe
*4
Rear Cushion Lever
*5
C-washer
Connect the parking brake cable No. 3 to the front brake shoe.

Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.

- SST
- 09718-00011
for 295 mm drum:
Install the rear brake shoe, brake shoe strut set and shoe lever with a new C-washer.

Text in Illustration *1
Rear Brake Shoe
*2
Brake Shoe Strut Set
*3
Brake Shoe Lever
*4
Automatic Adjust Lever
*5
C-washer
*6
E-ring
Install a new E-ring and the automatic adjust lever.
Connect the parking brake cable No. 3 to the front brake shoe.

Install the tension spring as shown in the illustration.

Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.

- SST
- 09718-00011
| 11. INSTALL FRONT BRAKE SHOE |
for 254 mm drum:
Install the return spring to each brake shoe.
Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.

- SST
- 09718-00011
Install the brake shoe lower strut.

Text in Illustration *A
LH Side
*B
RH Side
- NOTICE:
- Make sure that the shoe lower strut and brake rear cushion lever are securely engaged.
Using needle-nose pliers, install the tension spring.

for 295 mm drum:
Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.

- SST
- 09718-00011
Install the return spring to each brake shoe.
| 12. CONNECT PARKING BRAKE SHOE STRUT SET |
for 254 mm drum:
Using SST, install the upper side tension spring.

- SST
- 09703-30011
for 295 mm drum:
Using SST, install the upper side tension spring.

- SST
- 09703-30011
| 13. INSTALL AUTOMATIC ADJUST LEVER |
for 254 mm drum:
Install the automatic adjust lever and tension spring.

- NOTICE:
- Make sure to install the automatic adjust lever between the groove of the shoe strut set and brake shoe.
| 14. INSPECT REAR DRUM BRAKE |
Check the each part is installed properly.




Text in Illustration *A
for 254 mm Drum
*B
for 295 mm Drum
*C
LH Side
*D
RH Side
*a
Front
-
-
- NOTICE:
- There should be no oil or grease adhering to the friction surfaces of the shoe lining and drum.
If they are not installed correctly, reinstall them as shown in the illustration.
| 15. INSTALL REAR AXLE BRAKE DRUM GASKET |
Install the new brake drum gasket to the rear axle shaft.
| 16. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY |
| 17. ADJUST REAR DRUM BRAKE SHOE CLEARANCE |
Using a screwdriver from a service hole, turn the adjuster to expand the shoes so that the brake shoes touch the brake drum.


Text in Illustration *A
for 295 mm Drum
*B
for 254 mm Drum
Using another screwdriver, push up the automatic adjust lever and turn the adjuster to contract the shoes so that the brake shoe does not touch the brake drum. Then turn the adjuster another 180 degrees to further contract the shoes.


Text in Illustration *A
for 295 mm Drum
*B
for 254 mm Drum
Install the hole plug.
| 18. ADD BRAKE FLUID |
- Fluid:
- SAE J1703 or FMVSS No. 116 DOT3 or equivalent
| 19. BLEED BRAKE LINE |
Connect the vinyl tube to the bleeder plug.
Depress the brake pedal several times and loosen the bleeder plug with the pedal held down.
At the point where the fluid stops coming out, tighten the bleeder plug and release the brake pedal.
Repeat this procedure until the air in the brake fluid is completely bled out.
Tighten the bleeder plug.
Front bleeder plug:
- Torque:
- 10.8 N*m{ 110 kgf*cm , 8 ft.*lbf }
Rear bleeder plug:
- Torque:
- 11.0 N*m{ 112 kgf*cm , 8 ft.*lbf }
Repeat the above procedure to bleed the air out of the brake line for each wheel.
| 20. INSPECT BRAKE FLUID LEVEL |
Check the fluid level and add fluid if necessary.
- Fluid:
- SAE J1703 or FMVSS No.116 DOT3 or equivalent
| 21. INSTALL REAR WHEEL |
- Torque:
- 100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }
| 22. INSPECT PARKING BRAKE CONTROL HANDLE TRAVEL |
Pull firmly on the parking brake control handle.
Release the parking brake lock, and return the parking brake control handle to its off position.
Slowly pull the parking brake control handle all the way up, and count the number of clicks.
- Parking brake control handle travel:
- 10 to 16 clicks at 200 N (20 kgf, 44 lbf) (except Super Long Wheelbase)
- 12 to 18 clicks at 200 N (20 kgf, 44 lbf) (for Super Long Wheelbase)
- HINT:
- If the number of clicks falls outside of the specified range, release the parking brake lock and adjust it.
- If there are fewer clicks than the specified value, loosen the parking brake wire adjustment nut an the lock nut. With the parking brake cable loosened, adjust the clearance between the brake drum and lining.
- If the number of clicks falls outside of the specified range, release the parking brake lock and adjust it.
| 23. ADJUST PARKING BRAKE CONTROL HANDLE TRAVEL |
Lift the vehicle
Depress the parking brake handle. Hold the parking brake adjusting nut using a wrench, and loosen the lock nut.

Turn the parking brake adjusting nut until the parking brake handle travel meets the above specification.
- Parking brake control handle travel:
- 10 to 16 clicks at 200 N (20 kgf, 44 lbf) (except Super Long Wheelbase)
- 12 to 18 clicks at 200 N (20 kgf, 44 lbf) (for Super Long Wheelbase)
Count the number of clicks after depressing and releasing the parking brake control handle 3 or 4 times.
Check whether the parking brake drags or not.
When operating the parking brake control handle, check that the parking brake indicator light comes on.
- Standard:
- Brake warning light always comes on at the first click.
Hold the parking brake adjusting nut using a wrench, and tighten the lock nut.
- Torque:
- 14.5 N*m{ 148 kgf*cm , 11 ft.*lbf }
Lower the vehicle.
| 24. CHECK ABS SPEED SENSOR SIGNAL (w/ ABS) |
