Using SST and a hammer, install a new rear axle shaft oil seal.
SST
09554-22010
Seal installation depth:
34.5 to 35.5 mm (1.358 to 1.398 in.)
NOTICE:
Do not drive the oil seal in deeper than the specified range or an oil leak will occur.
Do not tilt the oil seal during installation.
Text in Illustration
*1
Rear Axle Housing Assembly
*2
Rear Axle Shaft Oil Seal
*a
Seal installation depth
Apply MP grease to the oil seal lip.
2.
INSTALL REAR AXLE SHAFT OIL SEAL (w/o ABS)
Using SST and a hammer, install a new rear axle shaft oil seal.
SST
09554-22010
Seal installation depth:
0.5 to 1.5 mm (0.0197 to 0.0590 in.)
NOTICE:
Do not drive the oil seal in deeper than the specified range or an oil leak will occur.
Do not tilt the oil seal during installation.
Text in Illustration
*1
Rear Axle Housing Assembly
*2
Rear Axle Shaft Oil Seal
*a
Seal installation depth
Apply MP grease to the oil seal lip.
3.
INSTALL BEARING RETAINER O-RING
Apply MP grease to the bearing retainer O-ring.
Install the bearing retainer O-ring to the rear axle shaft housing.
4.
INSTALL REAR AXLE SHAFT WITH BACKING PLATE
Install the rear axle shaft with backing plate to the rear axle shaft housing with the 4 nuts.
Torque:
65 N*m{
663 kgf*cm
, 48 ft.*lbf
}
NOTICE:
Be careful not to damage the rear axle shaft oil seal.
Be careful not to damage the skid control rotor rear.
5.
INSTALL REAR SPEED SENSOR (w/ ABS)
6.
INSTALL REAR WHEEL BRAKE CYLINDER ASSEMBLY
Install the wheel brake cylinder assembly with the 2 bolts.
Torque:
9.5 N*m{
97 kgf*cm
, 84 in.*lbf
}
Using a union nut wrench, connect the brake tube.
Torque:
Specified tightening torque:
15 N*m{
155 kgf*cm
, 11 ft.*lbf
}
Text in Illustration
*a
Torque Wrench Fulcrum Length
HINT:
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13 N*m (137 kgf*cm, 10 ft.*lbf)
7.
APPLY HIGH TEMPERATURE GREASE
Apply high temperature grease to the shoe attached surface of the backing plate.
Text in Illustration
*1
High temperature grease
8.
INSTALL PARKING BRAKE CABLE ASSEMBLY NO.3
Install the parking brake cable assembly No.3 to the rear brake backing plate with the 2 bolts.
Torque:
8.0 N*m{
82 kgf*cm
, 71 in.*lbf
}
9.
INSTALL PARKING BRAKE SHOE STRUT SET
Apply the high temperature grease to the adjusting bolt.
Text in Illustration
*1
High temperature grease
Install the tension spring to the shoe strut set.
10.
INSTALL REAR BRAKE SHOE
for 254 mm drum:
Using pliers, install the rear brake shoe, shoe strut set, rear cushion lever and shoe lever with a new C-washer.
Text in Illustration
*1
Brake Shoe Lever
*2
Brake Shoe Strut Set
*3
Rear Brake Shoe
*4
Rear Cushion Lever
*5
C-washer
Connect the parking brake cable No. 3 to the front brake shoe.
Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.
SST
09718-00011
for 295 mm drum:
Install the rear brake shoe, brake shoe strut set and shoe lever with a new C-washer.
Text in Illustration
*1
Rear Brake Shoe
*2
Brake Shoe Strut Set
*3
Brake Shoe Lever
*4
C-washer
Connect the parking brake cable No. 3 to the front brake shoe.
Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.
SST
09718-00011
11.
INSTALL FRONT BRAKE SHOE
for 254 mm drum:
Install the return spring to each brake shoe.
Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.
SST
09718-00011
Install the brake shoe lower strut.
Text in Illustration
*A
LH Side
*B
RH Side
NOTICE:
Make sure that the shoe lower strut and brake rear cushion lever are securely engaged.
Using needle-nose pliers, install the tension spring.
for 295 mm drum:
Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.
SST
09718-00011
Install the return spring to each brake shoe.
12.
CONNECT PARKING BRAKE SHOE STRUT SET
for 254 mm drum:
Using SST, install the upper side tension spring.
SST
09703-30011
for 295 mm drum:
Using SST, install the upper side tension spring.
SST
09703-30011
13.
INSTALL AUTOMATIC ADJUST LEVER
Install the automatic adjust lever and tension spring.
Text in Illustration
*A
for 295 mm Drum
*B
for 254 mm Drum
NOTICE:
Make sure to install the automatic adjust lever between the groove of the shoe strut set and brake shoe.
14.
INSPECT REAR DRUM BRAKE
Check the each part is installed properly.
Text in Illustration
*A
for 254 mm Drum
*B
LH Side
*C
RH Side
-
-
*a
Front
-
-
Text in Illustration
*A
for 295 mm Drum
*B
LH Side
*C
RH Side
-
-
*a
Front
-
-
NOTICE:
There should be no oil or grease adhering to the friction surfaces of the shoe lining and drum.
If they are not installed correctly, reinstall them as shown in the illustration.
15.
INSTALL REAR AXLE BRAKE DRUM GASKET
Install the new brake drum gasket to the rear axle shaft.
16.
INSTALL REAR BRAKE DRUM SUB-ASSEMBLY
17.
ADJUST REAR DRUM BRAKE SHOE CLEARANCE
Using a screwdriver from a service hole, turn the adjuster to expand the shoes so that the brake shoes touch the brake drum.
Text in Illustration
*A
for 295 mm Drum
*B
for 254 mm Drum
Using another screwdriver, push up the automatic adjust lever and turn the adjuster to contract the shoes so that the brake shoe does not touch the brake drum. Then turn the adjuster another 180 degrees to further contract the shoes.
Release the parking brake lock, and return the parking brake control handle to its off position.
Slowly pull the parking brake control handle all the way up, and count the number of clicks.
Parking brake control handle travel:
10 to 16 clicks at 200 N (20 kgf, 44 lbf) (except Super Long Wheelbase)
12 to 18 clicks at 200 N (20 kgf, 44 lbf) (for Super Long Wheelbase)
HINT:
If the number of clicks falls outside of the specified range, release the parking brake lock and adjust it.
If there are fewer clicks than the specified value, loosen the parking brake wire adjustment nut an the lock nut. With the parking brake cable loosened, adjust the clearance between the brake drum and lining.
23.
ADJUST PARKING BRAKE CONTROL HANDLE TRAVEL
Lift the vehicle
Depress the parking brake handle. Hold the parking brake adjusting nut using a wrench, and loosen the lock nut.
Turn the parking brake adjusting nut until the parking brake handle travel meets the above specification.
Parking brake control handle travel:
10 to 16 clicks at 200 N (20 kgf, 44 lbf) (except Super Long Wheelbase)
12 to 18 clicks at 200 N (20 kgf, 44 lbf) (for Super Long Wheelbase)
Count the number of clicks after depressing and releasing the parking brake control handle 3 or 4 times.
Check whether the parking brake drags or not.
When operating the parking brake control handle, check that the parking brake indicator light comes on.
Standard:
Brake warning light always comes on at the first click.
Hold the parking brake adjusting nut using a wrench, and tighten the lock nut.