2014-2019 Hiace · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Oct 2014 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017


1. INSTALL REAR AXLE SHAFT OIL SEAL (w/ ABS)

  1. A239133E01
    Using SST and a hammer, install a new rear axle shaft oil seal.
    SST
    09554-22010  

    Seal installation depth:
    34.5 to 35.5 mm (1.358 to 1.398 in.)

    NOTICE:
    1. Do not drive the oil seal in deeper than the specified range or an oil leak will occur.
    2. Do not tilt the oil seal during installation.

    Text in Illustration 
    *1
    Rear Axle Housing Assembly
    *2
    Rear Axle Shaft Oil Seal
    *a
    Seal installation depth

  1. Apply MP grease to the oil seal lip.


2. INSTALL REAR AXLE SHAFT OIL SEAL (w/o ABS)

  1. A239134E01
    Using SST and a hammer, install a new rear axle shaft oil seal.
    SST
    09554-22010  

    Seal installation depth:
    0.5 to 1.5 mm (0.0197 to 0.0590 in.)

    NOTICE:
    1. Do not drive the oil seal in deeper than the specified range or an oil leak will occur.
    2. Do not tilt the oil seal during installation.

    Text in Illustration 
    *1
    Rear Axle Housing Assembly
    *2
    Rear Axle Shaft Oil Seal
    *a
    Seal installation depth

  1. Apply MP grease to the oil seal lip.


3. INSTALL BEARING RETAINER O-RING
  1. Apply MP grease to the bearing retainer O-ring.

  1. Install the bearing retainer O-ring to the rear axle shaft housing.


4. INSTALL REAR AXLE SHAFT WITH BACKING PLATE

  1. C102664J01
    Install the rear axle shaft with backing plate to the rear axle shaft housing with the 4 nuts.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the rear axle shaft oil seal.
    2. Be careful not to damage the skid control rotor rear.


5. INSTALL REAR SPEED SENSOR (w/ ABS)
  1. Install the rear speed sensor LH with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Prevent foreign matter from attaching to the sensor tip.

  1. Attach the 3 clips.

  1. Connect the connector and attach the connector clamp.


6. INSTALL REAR WHEEL BRAKE CYLINDER ASSEMBLY

  1. C102608
    Install the wheel brake cylinder assembly with the 2 bolts.

    Torque:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }

  1. A329093E05
    Using a union nut wrench, connect the brake tube.

    Torque:
    Specified tightening torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    Text in Illustration 
    *a
    Torque Wrench Fulcrum Length

    HINT:
    1. Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
    2. When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13 N*m (137 kgf*cm, 10 ft.*lbf)


7. APPLY HIGH TEMPERATURE GREASE

  1. C102609E02
    Apply high temperature grease to the shoe attached surface of the backing plate.
    Text in Illustration 
    *1
    High temperature grease


8. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.3

  1. C102159
    Install the parking brake cable assembly No.3 to the rear brake backing plate with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


9. INSTALL PARKING BRAKE SHOE STRUT SET

  1. F042695E03
    Apply the high temperature grease to the adjusting bolt.
    Text in Illustration 
    *1
    High temperature grease

  1. Install the tension spring to the shoe strut set.


10. INSTALL REAR BRAKE SHOE

  1. for 254 mm drum:

    1. C102607E02
      Using pliers, install the rear brake shoe, shoe strut set, rear cushion lever and shoe lever with a new C-washer.
      Text in Illustration 
      *1
      Brake Shoe Lever
      *2
      Brake Shoe Strut Set
      *3
      Rear Brake Shoe
      *4
      Rear Cushion Lever
      *5
      C-washer

    2. C102606
      Connect the parking brake cable No. 3 to the front brake shoe.

    3. C102603E01
      Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  

  1. for 295 mm drum:

    1. C318086E01
      Install the rear brake shoe, brake shoe strut set and shoe lever with a new C-washer.
      Text in Illustration 
      *1
      Rear Brake Shoe
      *2
      Brake Shoe Strut Set
      *3
      Brake Shoe Lever
      *4
      C-washer

    2. C263529
      Connect the parking brake cable No. 3 to the front brake shoe.

    3. C318084E01
      Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  


11. INSTALL FRONT BRAKE SHOE

  1. for 254 mm drum:

    1. Install the return spring to each brake shoe.

    2. C102604E01
      Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  

    3. C264855E02
      Install the brake shoe lower strut.
      Text in Illustration 
      *A
      LH Side
      *B
      RH Side

      NOTICE:
      Make sure that the shoe lower strut and brake rear cushion lever are securely engaged.

    4. C102600
      Using needle-nose pliers, install the tension spring.

  1. for 295 mm drum:

    1. C318083E01
      Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  

    2. Install the return spring to each brake shoe.


12. CONNECT PARKING BRAKE SHOE STRUT SET

  1. for 254 mm drum:

    1. C231698E01
      Using SST, install the upper side tension spring.
      SST
      09703-30011  

  1. for 295 mm drum:

    1. C263526E01
      Using SST, install the upper side tension spring.
      SST
      09703-30011  


13. INSTALL AUTOMATIC ADJUST LEVER

  1. Install the automatic adjust lever and tension spring.

    C318099E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

    NOTICE:
    Make sure to install the automatic adjust lever between the groove of the shoe strut set and brake shoe.


14. INSPECT REAR DRUM BRAKE

  1. Check the each part is installed properly.

    C264221E03

    Text in Illustration 
    *A
    for 254 mm Drum
    *B
    LH Side
    *C
    RH Side
    -
    -
    *a
    Front
    -
    -

    C318088E01
    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    LH Side
    *C
    RH Side
    -
    -
    *a
    Front
    -
    -

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and drum.

  1. If they are not installed correctly, reinstall them as shown in the illustration.


15. INSTALL REAR AXLE BRAKE DRUM GASKET
  1. Install the new brake drum gasket to the rear axle shaft.


16. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY

17. ADJUST REAR DRUM BRAKE SHOE CLEARANCE

  1. Using a screwdriver from a service hole, turn the adjuster to expand the shoes so that the brake shoes touch the brake drum.

    C318089E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

  1. Using another screwdriver, push up the automatic adjust lever and turn the adjuster to contract the shoes so that the brake shoe does not touch the brake drum. Then turn the adjuster another 180 degrees to further contract the shoes.

    C318081E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

  1. Install the hole plug.


18. ADD BRAKE FLUID
  1. w/ VSC: (Click here)
  2. w/o VSC: (Click here)

19. BLEED BRAKE LINE
  1. w/ VSC: (Click here)
  2. w/o VSC: (Click here)

20. INSPECT BRAKE FLUID LEVEL
  1. w/ VSC: (Click here)
  2. w/o VSC: (Click here)

21. INSTALL REAR WHEEL

Torque:
100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }


22. INSPECT PARKING BRAKE CONTROL HANDLE TRAVEL
  1. Pull firmly on the parking brake control handle.

  1. Release the parking brake lock, and return the parking brake control handle to its off position.

  1. Slowly pull the parking brake control handle all the way up, and count the number of clicks.

    Parking brake control handle travel:
    10 to 16 clicks at 200 N (20 kgf, 44 lbf) (except Super Long Wheelbase)
    12 to 18 clicks at 200 N (20 kgf, 44 lbf) (for Super Long Wheelbase)

    HINT:
    1. If the number of clicks falls outside of the specified range, release the parking brake lock and adjust it.
    2. If there are fewer clicks than the specified value, loosen the parking brake wire adjustment nut an the lock nut. With the parking brake cable loosened, adjust the clearance between the brake drum and lining.


23. ADJUST PARKING BRAKE CONTROL HANDLE TRAVEL
  1. Lift the vehicle

  1. C102142E01
    Depress the parking brake handle. Hold the parking brake adjusting nut using a wrench, and loosen the lock nut.

  1. Turn the parking brake adjusting nut until the parking brake handle travel meets the above specification.

    Parking brake control handle travel:
    10 to 16 clicks at 200 N (20 kgf, 44 lbf) (except Super Long Wheelbase)
    12 to 18 clicks at 200 N (20 kgf, 44 lbf) (for Super Long Wheelbase)

  1. Count the number of clicks after depressing and releasing the parking brake control handle 3 or 4 times.

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake control handle, check that the parking brake indicator light comes on.

    Standard:
    Brake warning light always comes on at the first click.

  1. Hold the parking brake adjusting nut using a wrench, and tighten the lock nut.

    Torque:
    14.5 N*m{ 148 kgf*cm , 11 ft.*lbf }

  1. Lower the vehicle.


24. CHECK ABS SPEED SENSOR SIGNAL (w/ ABS)
  1. w/ VSC: (Click here)
  2. w/o VSC: (Click here)
← INSTALLATION (Oct 2014 – Mar 2016)INSTALLATION (Jan 2017 – Nov 2017) →