2014-2019 Hiace · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017


1. INSTALL FRONT AXLE HUB BEARING

  1. C308239E01
    Using SST and a press, install a new front axle hub bearing.
    SST
    09649-17010  
    09950-70010   (09951-07100)

    NOTICE:
    Do not press on or damage the bearing seal of the front axle hub bearing.

    HINT:
    Make sure the lip of the front axle hub bearing faces the vehicle exterior.


2. INSTALL FRONT DISC

  1. C113549E02
    Install the front disc as shown in the illustration.

  1. C102293E01
    Install the front disc with the 6 bolts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }


3. INSTALL FRONT WHEEL ADJUSTING NUT (w/ ABS)
  1. Install the hub nut to the front axle hub bolt.

  1. Hold the front axle assembly in a vise between aluminium plates.

    NOTICE:
    1. Do not overtighten the vise.
    2. Hold the hub nut in a vise to secure the axle hub and bearing assembly.

  1. C194737E01
    Install the skid control rotor as shown in the illustration.

  1. C187394E01
    Using SST, install the front wheel adjusting nut.
    SST
    09607-26010  

    Torque:
    287 N*m{ 2,930 kgf*cm , 212 ft.*lbf }

    NOTICE:
    Do not use an extension bar to avoid applying excess torque to the nut and rotor.

  1. C187395
    Using a chisel and hammer, stake the front wheel adjusting nut.


4. INSTALL FRONT WHEEL ADJUSTING NUT (w/o ABS)
  1. Install the hub nut to the front axle hub bolt.

  1. Hold the front axle assembly in a vise between aluminium plates.

    NOTICE:
    1. Do not overtighten the vise.
    2. Hold the hub nut in a vise to secure the axle hub and bearing assembly.

  1. C111785
    Install the front wheel bearing dust deflector as shown in the illustration.

  1. C182087E02
    Using SST, install the front wheel adjusting nut.
    SST
    09607-26010  

    Torque:
    287 N*m{ 2,930 kgf*cm , 212 ft.*lbf }

    NOTICE:
    Do not use an extension bar to avoid applying excess torque to the nut and rotor.

  1. C187554
    Using a chisel and hammer, stake the front wheel adjusting nut.


5. INSTALL INNER KNUCKLE GREASE RETAINER CAP (w/ Cap)

  1. C194037E01
    Using SST, place the steering knuckle on a press as shown in the illustration.
    SST
    09527-30010  

  1. C194038
    Temporarily install a new inner knuckle grease retainer cap to the steering knuckle as shown in the illustration.

    NOTICE:
    Align the center of the cutout in the inner knuckle grease retainer cap and the groove of the steering knuckle.

  1. C194039E01
    Using SST and the press, press the inner knuckle grease retainer cap into the steering knuckle until the distance (A) in the illustration meets the standard value.
    SST
    09950-70010   (09951-07100)
    09951-00900  

    Distance (A):
    26 +/- 0.5 mm (1.02 +/- 0.0196 in.)

    NOTICE:
    Using a vernier caliper, measure the distance (A) at the 3 points indicated by the arrows in the illustration while pressing.


6. INSTALL FRONT LOWER BALL JOINT ASSEMBLY
  1. Fix the steering knuckle in the vise using aluminium plates.

    NOTICE:
    Do not damage the steering knuckle.

  1. Install the front lower ball joint assembly to the steering knuckle with the nut.

    Torque:
    170 N*m{ 1,730 kgf*cm , 125 ft.*lbf }

    NOTICE:
    1. Ensure that the thread and taper are free of oil etc.
    2. Do not damage the lower ball joint dust boot.

  1. Install a new cotter pin to the front lower ball joint assembly.

    NOTICE:
    Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.


7. INSTALL STEERING KNUCKLE

  1. C102290E01
    Install the steering knuckle and brake dust cover to the front axle hub sub-assembly with the 4 bolts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }


8. INSTALL OUTER KNUCKLE GREASE RETAINER CAP (w/ Cap)

  1. C194041E01
    Using SST, install a new outer knuckle grease retainer cap.
    SST
    09950-60010   (09951-00420)
    09950-70010   (09951-07150)


9. INSTALL FRONT AXLE ASSEMBLY
  1. Temporarily install the front axle assembly to the front suspension upper arm and front suspension lower arm.

  1. C102287E02
    Fully tighten front suspension lower arm with the 4 bolts and 4 nuts.

    Torque:
    Nut (A):
    90 N*m{ 918 kgf*cm , 66 ft.*lbf }
    Nut (B):
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

  1. C102007E01
    Fully tighten the front suspension upper arm with the nut.

    Torque:
    113 N*m{ 1,147 kgf*cm , 83 ft.*lbf }

    NOTICE:
    Do not damage the lower ball joint dust boot.

  1. Install a new cotter pin to the front suspension upper arm.

    NOTICE:
    Further tighten the castle nut up to 60° if the holes for the cotter pin are not aligned.


10. INSTALL TIE ROD END SUB-ASSEMBLY
  1. Install the tie rod end sub-assembly to the steering knuckle with the castle nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

    NOTICE:
    Do not damage the lower ball joint dust boot.

  1. Install a new cotter pin to the tie rod end sub-assembly.

    NOTICE:
    Further tighten the castle nut up to 60° if the holes for the cotter pin are not aligned.


11. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

  1. C102283E01
    Install the brake caliper assembly to the steering knuckle with the 2 bolts.

    Torque:
    123 N*m{ 1,250 kgf*cm , 91 ft.*lbf }


12. INSTALL FRONT SPEED SENSOR (w/ ABS)

  1. C102281E01
    Install the speed sensor to the steering knuckle with the 2 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.
    3. Do not twist the sensor wire when installing the speed sensor.


13. INSPECT FRONT AXLE HUB BEARING LOOSENESS

  1. C103109
    Using a dial indicator, check for runout on the surface of the front axle hub outside the hub bolt.

    Maximum:
    0.07 mm (0.0028 in.)

    NOTICE:
    Ensure that the dial indicator is set at right angles to the measurement surface.

    If runout exceeds the maximum, replace the front axle hub.


14. INSPECT FRONT AXLE HUB RUNOUT

  1. C103108
    Using a dial indicator, check for looseness near the center of the front axle hub.

    Maximum:
    0.05 mm (0.0020 in.)

    NOTICE:
    Ensure that the dial indicator is set at right angles to the measurement surface.

    If looseness exceeds the maximum, replace the bearing.


15. INSTALL FRONT WHEEL

Torque:
100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }


16. INSPECT WHEEL ALIGNMENT
(Click here)

17. CHECK ABS SPEED SENSOR SIGNAL
(Click here)
← REMOVAL (from Oct 2014)INSTALLATION (Jan 2015 – Nov 2015) →