2014-2019 Hiace · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE TRANSMISSION OIL LEVEL GAUGE SUB-ASSEMBLY

  1. C101767
    Remove the transmission oil level gauge sub-assembly from the transmission oil filler tube sub-assembly.


3. DRAIN AUTOMATIC TRANSMISSION FLUID

  1. C158131E01
    Remove the drain plug and gasket and drain automatic transmission fluid.

  1. Install the drain plug with a new gasket.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


4. REMOVE TURBINE OUTLET ELBOW STAY (w/ DPF)

  1. C248714
    Remove the 2 bolts, 2 nuts and turbine outlet elbow stay.


5. REMOVE PROPELLER SHAFT ASSEMBLY
(Click here)

6. REMOVE FRONT EXHAUST PIPE ASSEMBLY (w/o DPF)

  1. A242354
    Remove the 2 bolts and 2 compression springs.

  1. Disconnect the No. 4 exhaust pipe support and front exhaust pipe.

  1. Remove the gasket.


7. REMOVE FRONT EXHAUST PIPE ASSEMBLY (w/ DPF)
  1. Disconnect the exhaust gas temperature sensor connector and detach the clamp.

  1. Disconnect the No. 2 exhaust gas temperature sensor connector and detach the 2 clamps.

  1. Disconnect the No. 3 exhaust gas temperature sensor connector and detach the 2 clamps.

  1. A262923
    Disconnect the No. 1 exhaust pipe air hose and No. 7 exhaust pipe air hose from the front exhaust pipe.

  1. A239813
    Remove the 2 No. 4 exhaust pipe supports.

  1. Remove the 3 nuts and front exhaust pipe.

  1. Remove the gasket.


8. REMOVE STARTER ASSEMBLY
  1. for 2.2 kW Type:
    Remove starter assembly (Click here).

  1. for 2.7 kW Type:
    Remove starter assembly (Click here).


9. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

  1. C101768E02
    Remove the 2 bolts and transmission oil filler tube sub-assembly.

  1. Remove the O-ring from the oil filler tube sub-assembly.


10. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

  1. C101771E03
    Remove the nut and disconnect the transmission control cable assembly from the transmission control shaft lever assembly.

  1. Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


11. DISCONNECT OIL COOLER TUBE

  1. Remove the 5 bolts and disconnect the 3 oil cooler tube clamps.

    C158420

  1. C158421
    Using a 17 mm union nut wrench, disconnect the 2 oil cooler tubes from each oil cooler tube union.


12. DISCONNECT CONNECTOR

  1. w/ Speedometer Sensor:

    1. C157537
      Disconnect the speedometer sensor connector.

  1. C248708E01
    Disconnect the temperature sensor connector.

  1. C248710
    Disconnect the park/neutral position switch connector.

  1. C101774E04
    Disconnect the No. 2 vehicle speed sensor connector and transmission wire connector.

  1. C101773E02
    Disconnect the overdrive direct clutch speed sensor connector.


13. DISCONNECT WIRE HARNESS

  1. C157538
    Remove the 2 bolts and disconnect the wire harness from the automatic transmission assembly.


14. REMOVE NO. 4 CYLINDER BLOCK INSULATOR

  1. C101776E02
    Remove the No. 4 cylinder block insulator.


15. REMOVE STIFFENER PLATE RH(ATM)

  1. C230787
    Remove the 3 bolts and stiffener plate RH.


16. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

  1. C101778E02
    Remove the bolt and drive plate cover from the automatic transmission assembly.

  1. C101779
    Turn the crankshaft pulley and remove the 6 drive plate and torque converter clutch setting bolts.


17. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

  1. C160266
    Support the automatic transmission assembly with a transmission jack.


18. SEPARATE ENGINE MOUNTING REAR INSULATOR ASSEMBLY

  1. C101781
    Remove the bolt, the nut and the washer and separate the engine mounting rear insulator assembly.


19. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

  1. C154015
    Remove the 5 bolts and automatic transmission assembly.

    NOTICE:
    Do not use excess force to pry off the transmission assembly.


20. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

  1. C101783
    Remove the 2 bolts and the No. 1 transmission control cable bracket from the automatic transmission housing.


21. REMOVE ENGINE MOUNTING REAR INSULATOR ASSEMBLY

  1. C101785
    Remove the 4 bolts and engine mounting rear insulator assembly from the extension housing sub-assembly.


22. REMOVE BREATHER PLUG HOSE

  1. C101784
    Remove the bolt and breather plug hose from the automatic transmission housing.


23. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY

  1. C108498E01
    Put a matchmark on the automatic transmission housing and the torque converter clutch assembly.

  1. Remove the torque converter clutch assembly from the automatic transmission assembly.


24. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

  1. D029377E02
    Inspect the one-way clutch.

    1. Install the SST so that it fits in the notch of the converter hub and the outer race of the one-way clutch.

      SST
      09350-32014   (09351-32010, 09351-32020)

    2. Install the SST (Stopper) from the sleeve of torque converter assembly and engage serration of stater slight washer.

    3. Stand up the torque converter and turn the SST (tool ).

      SST
      09350-32014   (09351-32010, 09351-32020)

      Standard:
      Check if it rotates smoothly when turned clockwise and locks up when turned counter clockwise.

  1. D025367E01
    Determine the condition of the torque converter clutch assembly.

    1. If the inspection result of the torque converter clutch assembly meets the following item, replace the torque converter clutch.

      Malfunction item:
      Any metallic sound is heard from the torque converter clutch during stall test or when the shift lever is in the N position.
      The one-way clutch is free or locked in both directions.
      Fine powder exceeding the sample limit is identified in ATF. (See the sample.)

      HINT:
      1. The sample shows the auto fluid of approximately 0.25 liters (0.26 US qts, 0.22 Imp, qts) that is taken out from the removed torque converter clutch.

  1. Replace the ATF in the torque converter clutch.

    1. If the ATF is discolored and/or has a foul odor, completely stir the ATF in the torque converter clutch and drain it with the installation face up.

  1. C011090
    Clean and check the oil cooler and oil pipe line.

    1. If the torque converter clutch is inspected or exchange the ATF, is exchanged, clean the oil cooler and oil pipe line.

      HINT:
      1. Spray compressed air of 196 kPa (2kgf/cm2, 28 psi) from the inlet hose.
      2. If plenty of fine powders are identified in the ATF, add a new ATF using a bucket pump and clean it again.

    2. If the ATF is cloudy, inspect the oil cooler.

← REMOVAL (Oct 2014 – Dec 2014)REMOVAL (Apr 2016 – Dec 2016) →