2014-2019 Hiace · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017


1. INSTALL TRANSMISSION WIRE

  1. C058095E01
    Coat a new O-ring with ATF and install it to the transmission wire.

  1. G022489
    Install the transmission wire with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


2. CONNECT TRANSMISSION WIRE

  1. w/o Flex Lock-up:
    Connect the 4 connectors.

    C364901E01

    Text in Illustration 
    *A
    w/ Flex Lock-up
    *B
    w/o Flex Lock-up
    *1
    ATF Temperature Sensor
    -
    -

  1. w/ Flex Lock-up:

    1. Attach the ATF temperature sensor to the temperature sensor clamp.

    2. Connect the 4 connectors.


3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

  1. G021841E03
    Install 3 new gaskets.

  1. Install the oil strainer with the 4 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    Bolt length:

    Bolt A:
    14 mm (0.55 in.)
    Bolt B:
    20 mm (0.79 in.)
    Bolt C:
    23 mm (0.91 in.)


4. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

  1. D029014E02
    Install the 3 magnets in the indications of the oil pan sub-assembly.

  1. Remove any packing material and be careful not to drop oil on the contacting surfaces of the transmission case and oil pan sub-assembly .

    NOTICE:
    Apply seal packing to the contact surface and install the oil pan with in 10 minutes of application.

  1. D028715
    Apply FIPG to the oil pan, as shown in the illustration.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. G022488
    Uniformly tighten the 19 bolts in several times and install the transmission oil pan.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


5. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

  1. C101768E01
    Coat a new O-ring with ATF, and install it to the oil filler tube.

  1. Install the oil filler tube to the automatic transmission with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

7. ADD AUTOMATIC TRANSMISSION FLUID

8. INSPECT AUTOMATIC TRANSMISSION FLUID

HINT:
Drive the vehicle so that the engine and transmission are at normal operating temperature.

Fluid temperature:
70 to 80 °C (158 to 176 °F)

  1. D025120E01
    Park the vehicle on a level surface and set the parking brake.

  1. With the engine idling and the brake pedal depressed, move shift the lever into all positions from P to L and return to the P position.

  1. Take out the dipstick and wipe it clean.

  1. Put it back all the way.

  1. Take it out again and check that the fluid level is within the HOT range.
    If the fluid level is below the HOT range, add new fluid and recheck the fluid level. If the fluid level exceeds the HOT range, drain the fluid once, add the proper amount of new fluid and recheck the fluid level.


9. PERFORM INITIALIZATION
(Click here)
← INSTALLATION (Apr 2016 – Dec 2016)COMPONENTS (from Oct 2014) →