2014-2019 Hiace · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017


1. INSTALL SHIFT SOLENOID VALVE

  1. Install the shift solenoid valve SLT and solenoid lock plate with the bolt.

    Torque:
    6.4 N*m{ 65 kgf*cm , 56 in.*lbf }


    C367920E01
    Text in Illustration 
    *A
    w/ Flex Lock-up
    *B
    w/o Flex Lock-up
    *1
    Shift Solenoid Valve S1
    *2
    Shift Solenoid Valve S2
    *3
    Temperature Sensor Clamp
    *4
    Solenoid Clamp
    *5
    Shift Solenoid Valve SLU
    *6
    Shift Solenoid Valve SL
    *7
    Solenoid Lock Plate
    *8
    Shift Solenoid Valve SLT

  1. w/o Flex Lock-up:

    1. Coat a new O-ring with ATF and install it to the shift solenoid valve SL.

    2. Install the shift solenoid valve SL with the bolt.

      Torque:
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. w/ Flex Lock-up:

    1. Install the solenoid clamp and shift solenoid valve SLU with the bolt.

      Torque:
      6.6 N*m{ 67 kgf*cm , 59 in.*lbf }

    2. Install the temperature sensor clamp with the bolt.

      Torque:
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Coat a new O-ring with ATF and install it to the shift solenoid valve S2.

  1. Coat a new O-ring with ATF and install it to the shift solenoid valve S1.

  1. Install the shift solenoid valve S2 and shift solenoid valve S1 with the bolt.

    Torque:
    6.6 N*m{ 67 kgf*cm , 59 in.*lbf }


2. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

  1. AT08393E01
    Align the groove of the manual valve with the pin of the lever.

  1. D029011E02
    Install the 20 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    Bolt length:

    Bolt A:
    23 mm (0.91 in.)
    Bolt B:
    28 mm (1.10 in.)
    Bolt C:
    36 mm (1.42 in.)


3. CONNECT TRANSMISSION WIRE
(Click here)

4. ADD AUTOMATIC TRANSMISSION FLUID

5. INSPECT AUTOMATIC TRANSMISSION FLUID

HINT:
Drive the vehicle so that the engine and transmission are at normal operating temperature.

Fluid temperature:
70 to 80 °C (158 to 176 °F)

  1. D025120E01
    Park the vehicle on a level surface and set the parking brake.

  1. With the engine idling and the brake pedal depressed, move shift the lever into all positions from P to L and return to the P position.

  1. Take out the dipstick and wipe it clean.

  1. Put it back all the way.

  1. Take it out again and check that the fluid level is within the HOT range.
    If the fluid level is below the HOT range, add new fluid and recheck the fluid level. If the fluid level exceeds the HOT range, drain the fluid once, add the proper amount of new fluid and recheck the fluid level.


6. PERFORM INITIALIZATION
(Click here)
← INSTALLATION (Apr 2016 – Dec 2016)ON-VEHICLE INSPECTION (from Oct 2014) →