INSTALLATION
Removal / installation · Vehicles built from Jan 2017
Versions by build date: Oct 2014 – Dec 2016 from Jan 2017
| 1.
INSTALL ENGINE REAR OIL SEAL |
 |
Apply MP grease to a new oil seal lip.
- NOTICE:
- Keep the lip free from foreign matter.
- Using SST and a hammer, tap in the oil seal until its surface is flush with the rear oil seal retainer edge.
- SST
- 09223-15030
09950-70010
(09951-07150)
- NOTICE:
- Wipe off extra grease from the crankshaft.
| 2.
INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)
|
 |
- HINT:
- If any one of the mounting bolts is broken or deformed, replace it.
- Apply adhesive to 2 or 3 threads of the mounting bolt end.
- Adhesive:
- Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the flywheel.
- Fix the crankshaft with SST.
- SST
- 09213-54015
(91651-60855)
09330-00021
- Install and uniformly tighten the 10 mounting bolts in several steps in the sequence shown in the illustration.(*1)
-
Torque:
- 27 N*m{
276 kgf*cm
, 20 ft.*lbf
}
If any one of the mounting bolts does not meet the torque specification, replace the mounting bolt.
- Mark the mounting bolt with paint.(*2)
Retighten the mounting bolt by 90° in the order shown in step (*1).
Check that the painted mark is now at a 90° angle to that in step (*2).
| 3.
INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)
|
 |
- Apply adhesive to 2 or 3 threads of the mounting bolt end.
- Adhesive:
- Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the spacer FR, drive plate and spacer RR on the crankshaft.
- NOTICE:
- Do not start the engine for at least 1 hour after installing.
- Fix the crankshaft with SST.
- SST
- 09213-54015
(91651-60855)
09330-00021
- Install and uniformly tighten the 10 mounting bolts in several steps in the sequence shown in the illustration.
-
Torque:
- 74 N*m{
750 kgf*cm
, 55 ft.*lbf
}
| 4.
INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)
|
 |
- Insert SST into the clutch disc assembly, then insert them into the flywheel sub-assembly.
- SST
- 09301-00110
- NOTICE:
- Take care not to insert the clutch disc assembly in the wrong direction.
| 5.
INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)
|
 |
- Align the matchmark on the clutch cover assembly with the one on the flywheel sub-assembly.
Following the procedures shown in the illustration, tighten the 6 bolts starting from the bolt located near the knock pin on the top.
- SST
- 09301-00110
-
Torque:
- 19 N*m{
195 kgf*cm
, 14 ft.*lbf
}
- HINT:
- Evenly tighten the bolts by following the order shown in the illustration.
- Tighten the bolts after checking that the disc is in the center by lightly moving the SST up and down, left and right.
| 6.
INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)
|
 |
- Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.
- Maximum non-alignment:
- 0.9 mm (0.035 in.)
- If alignment is not as specified, adjust the diaphragm spring tip alignment using SST.
- SST
- 09333-00013
| 7.
INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission) |
 |
(Click here)
| 8.
INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission) |
 |
(Click here)
| 9.
PERFORM INITIALIZATION |
 |
(Click here)