2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

CAUTION:
As the engine assembly with transmission is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.


1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)

2. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. REMOVE NO. 1 ENGINE UNDER COVER (w/ Cover)

5. REMOVE NO. 2 ENGINE UNDER COVER (w/ Cover)

6. REMOVE ENGINE SIDE UNDER COVER LH (w/ Cover)

7. REMOVE ENGINE SIDE UNDER COVER RH (w/ Cover)

8. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the engine coolant in a container and dispose of it according to local regulations.

  1. Loosen the radiator drain cock plug and drain the engine coolant.

    A340635E01

    Text in Illustration 
    *A
    w/ Dual VVT-i
    *B
    w/o Dual VVT-i
    *1
    Radiator Reservoir Cap Sub-assembly
    *2
    Radiator Reservoir Assembly
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Water Drain Cock Plug
    *5
    2-Way
    -
    -

  1. Remove the radiator reservoir cap sub-assembly.

  1. Loosen the cylinder block water drain cock plug and drain the engine coolant from the engine.


9. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and drain the engine oil from the oil pan sub-assembly.

    NOTICE:
    Collect the oil in a disposable oil container.

  1. Clean the oil pan drain plug and install it with a new gasket.

    Torque:
    38 N*m{ 382 kgf*cm , 28 ft.*lbf }


10. REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)

HINT:
Use the same procedure described for the LH side. (Click here)


11. REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)

HINT:
Use the same procedure described for the LH side. (Click here)


12. REMOVE FRONT DOOR SCUFF PLATE RH

13. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Roll up the carpet, and remove the 5 bolts and engine service hole sub cover sub-assembly.


14. REMOVE FAN AND GENERATOR V BELT

  1. A102135E01
    Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward and decrease the tension in the drive belt. Then remove the drive belt.

    NOTICE:
    When removing the drive belt, do not use the idle pulley's bolt.

    HINT:
    After removing the drive belt, move the tensioner upward to the maximum amount.


15. DISCONNECT NO. 4 RADIATOR HOSE
  1. Slide the clamp and disconnect the No. 4 radiator hose from the engine.


16. DISCONNECT NO. 2 RADIATOR HOSE
  1. Slide the clamp and disconnect the No. 2 radiator hose from the No. 1 radiator pipe.


17. DISCONNECT INLET HEATER WATER HOSE A
  1. Slide the clamp and disconnect the inlet heater water hose A from the heater unit.


18. DISCONNECT OUTLET HEATER WATER HOSE B
  1. Slide the clamp and disconnect the outlet heater water hose B from the heater unit.


19. DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

  1. A340097
    Slide the clamp and disconnect the fuel vapor feed hose from the purge VSV.


20. DISCONNECT UNION TO CONNECTOR TUBE HOSE
  1. Slide the clamp and disconnect the union to connector tube hose from the intake manifold.


21. REMOVE AIR PRESSURE SENSOR

  1. A259661
    Disconnect the connector.

  1. Disconnect the vacuum hose and clamp.

  1. Detach the wire harness clamp

  1. Remove the 2 bolts and air pressure sensor together with the bracket.

  1. A259662
    Remove the bolt and air pressure sensor.


22. REMOVE INTAKE AIR CONNECTOR

  1. A102437
    Slide the clamp and disconnect the No. 2 ventilation hose from the cylinder head cover sub-assembly.

  1. Disconnect the vacuum hose from the intake air connector.

  1. Loosen the 2 hose clamps.

  1. Remove the 2 bolts and intake air connector.


23. DISCONNECT NO. 5 AIR HOSE
  1. Slide the clamp and disconnect the No. 5 air hose from the air switching valve assembly.


24. DISCONNECT NO. 1 FUEL HOSE

  1. A309365
    Disconnect the No. 1 fuel hose from the fuel pressure pulsation damper assembly (Click here).


25. DISCONNECT NO. 2 FUEL HOSE
  1. Disconnect the No. 2 fuel hose from the fuel delivery pipe sub-assembly (Click here).


26. DISCONNECT VANE PUMP ASSEMBLY

  1. A102130E01
    Disconnect the oil pressure switch connector.

  1. Remove the 2 bolts and disconnect the vane pump assembly from the engine.

  1. Support the vane pump assembly securely.


27. REMOVE ENGINE OIL LEVEL DIPSTICK

28. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A102132E01
    Remove the bolt and engine oil level dipstick guide.


29. DISCONNECT COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System)
  1. Disconnect the compressor and magnetic clutch connector.

  1. A102804E02
    Remove the 4 bolts and disconnect the compressor and magnetic clutch from the engine.

    HINT:
    Disconnect the compressor and magnetic clutch with the No. 1 cooler refrigerant suction hose and No. 1 cooler refrigerant discharge hose stuck by suspended from the rope.

  1. Support the compressor and magnetic clutch securely.


30. DISCONNECT ENGINE WIRE
  1. Disconnect the wire harness support of the ECM.

  1. Disconnect the connectors of the ECM.

  1. Disconnect the clamps of the engine wire and ground cable.

  1. Disconnect the starter connector (Click here).

  1. Disconnect the generator connector (Click here).

  1. A101143E05
    Remove the nut and disconnect the 4 connectors from the engine room junction block.
    Text in Illustration 
    *1
    Nut


31. REMOVE FRONT EXHAUST PIPE ASSEMBLY (for Super Long Wheelbase)
  1. w/ Secondary air injection system:

    1. Disconnect the fuel ratio sensor connector.

    2. Remove the fuel ratio sensor. (Click here)

  1. For unleaded gasoline engine:

    1. Disconnect the oxygen sensor connector.

    2. Remove the oxygen sensor. (Click here)

  1. Remove the 4 bolts, 2 nuts, and 2 compression springs.

  1. Remove the 2 gaskets from the exhaust pipe assembly front.

  1. Disconnect the exhaust pipe support, and remove the exhaust pipe assembly front.


32. REMOVE FRONT EXHAUST PIPE ASSEMBLY (for Long Wheelbase)
  1. w/ Secondary air injection system:

    1. Disconnect the fuel ratio sensor connector.

    2. Remove the fuel ratio sensor. (Click here)

  1. For unleaded gasoline engine:

    1. Disconnect the oxygen sensor connector.

    2. Remove the oxygen sensor. (Click here)

  1. Remove the 4 bolts, 2 nuts, and 2 compression springs.

  1. Remove the 2 gaskets from the exhaust pipe assembly front.

  1. Disconnect the exhaust pipe support, and remove the exhaust pipe assembly front.


33. REMOVE CENTER EXHAUST PIPE ASSEMBLY (for Super Long Wheelbase)
  1. Remove the 2 bolts and gasket from the exhaust pipe assembly center.

  1. Disconnect the exhaust pipe supports, and remove the exhaust pipe assembly center.


34. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Super Long Wheelbase)

  1. C102185E01
    Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller with center bearing shaft assembly from the differential companion flange.

  1. C107214
    Remove the 2 bolts and center support bearing assembly No.1.

  1. Remove the propeller with center bearing shaft assembly.

  1. C102186E01
    Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission.

      SST
      09325-40010  

    2. Use the following SST for the manual transmission.

      SST
      09325-20010  


35. REMOVE PROPELLER SHAFT ASSEMBLY (for Long Wheelbase)

  1. C102185E01
    Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller shaft assembly from the differential companion flange.

  1. Remove the propeller shaft assembly.

  1. C102186E01
    Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission

      SST
      09325-40010  

    2. Use the following SST for the manual transmission

      SST
      09325-20010  


36. REMOVE FRONT SPEED SENSOR LH

  1. C102281E01
    Remove the 2 bolts, and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Be careful not to damage the speed sensor.
    2. Prevent foreign matter from adhering to the speed sensor.


37. REMOVE FRONT SPEED SENSOR RH

HINT:
Use the same procedure described for the LH side.


38. REMOVE FRONT DISC BRAKE CALIPER ASSEMBLY LH

  1. C102283E01
    Remove the 2 bolts, and disconnect the brake caliper assembly.

    NOTICE:
    Use a wire or an equivalent to keep the brake caliper from hanging down by the flexible hose.


39. REMOVE FRONT DISC BRAKE CALIPER ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


40. SEPARATE FRONT SUSPENSION SUB-ASSEMBLY UPPER LH

  1. C101998E01
    Remove the cotter pin and loosen the nut.
    SST
    09628-62011  

    NOTICE:
    Do not remove the nut.

  1. Using SST, separate the steering knuckle from the suspension upper arm and remove the nut.

    NOTICE:
    1. Fix the steering knuckle with a wire so that the flexible hose does not receive excessive force.
    2. Do not damage the ball joint dust cover.


41. SEPARATE FRONT SUSPENSION SUB-ASSEMBLY UPPER RH

HINT:
Use the same procedure described for the LH side.


42. SEPARATE FRONT SHOCK ABSORBER ASSEMBLY LH

  1. C102009E02
    Remove the bolt and separate the front shock absorber from the front suspension lower arm.


43. SEPARATE FRONT SHOCK ABSORBER ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


44. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transmission)

  1. C102206E01
    Put matchmarks on the control cable assembly and the outer lever.

  1. Remove the 2 nuts and separate the transmission control cable from the outer lever.

  1. C102207
    Using a screwdriver, disengage the claws of the 2 clips.

  1. Remove the transmission control cable and 2 clips from the transmission control cable bracket No.1.


45. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transmission)

  1. C102209
    Remove the 2 bolts and separate the clutch release cylinder.


46. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)

  1. C318928
    Remove the clip, nut and disconnect the transmission control cable assembly from the control shaft lever and No. 1 transmission control cable bracket.

  1. C101804E02
    Remove the 2 bolts and disconnect the transmission control cable assembly.
    Text in Illustration 
    *a
    Front

  1. C101807E02
    Disconnect the transmission control cable assembly from the No. 2 transmission control cable bracket.
    Text in Illustration 
    *a
    Front

  1. Remove the 2 nuts and No. 2 transmission control cable bracket from the body.

  1. C101806E01
    Disconnect the transmission control cable assembly from the No. 3 transmission control cable bracket.
    Text in Illustration 
    *a
    Front

  1. Remove the 2 nuts and No. 3 transmission control cable bracket from the body.

  1. C101805E02
    Roll up the floor carpet of the front seat LH and remove the 2 bolts and transmission control cable assembly.
    Text in Illustration 
    *a
    Front


47. DISCONNECT OIL COOLER HOSE (for Automatic Transmission)
  1. Slide the 2 clamps and disconnect the inlet oil cooler hose and outlet oil cooler hose from the oil cooler tube.


48. SEPARATE STEERING TORQUE SHAFT ASSEMBLY

  1. C106142E01
    Loosen bolt (A) and remove bolt (B), then slide the steering torque shaft assembly.

    HINT:
    1. Do not remove bolt (A).
    2. Do not disconnect the steering torque shaft assembly from the power steering link assembly.

  1. C106143E01
    Put matchmarks on the steering torque shaft assembly and the power steering link assembly.

  1. Separate the steering torque shaft assembly from the power steering link assembly.


49. REMOVE ENGINE ASSEMBLY WITH TRANSMISSION
  1. Using the engine lifter, hold the engine assembly and separate the rear engine mount.

    NOTICE:
    1. Place wooden blocks or plate lift attachments so that the engine is level.
    2. With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
    3. Never install attachments to the oil pan of the engine assembly or transmission as doing so may deform the oil pan.

  1. A101144E07
    Remove the stabilizer brackets and 16 bolts of the front suspension crossmember sub-assembly.
    Text in Illustration 
    *a
    Front Side

  1. Operate the engine lifter, and then slowly remove the engine from the vehicle.

    NOTICE:
    1. Make sure the engine is clear of all wiring and hoses.
    2. While lowering the engine from the vehicle, do not allow it to contact the vehicle.

  1. Attach an engine sling device and hang the engine with a chain block.

    NOTICE:
    Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.


50. INSTALL ENGINE HANGER

  1. G037564E04
    Install the 2 engine hangers with the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    Text in Illustration 
    *A
    LH Side
    *B
    RH Side

    NOTICE:
    Use new 2 bolts for the 2 engine hangers.

    HINT:
    Engine Hangers
    12281-75050
    Bolt
    91672-81025


51. REMOVE STARTER ASSEMBLY
  1. for 1.6 kW (Click here)
  2. for 2.0 kW (Click here)

52. REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
(Click here)

53. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)

54. FIX ENGINE ASSEMBLY
  1. Using wooden blocks or plate lift attachments, set the engine on a flat surface.

    NOTICE:
    1. Place wooden blocks or plate lift attachments so that the engine is level.
    2. Never install attachments to the oil pan of the engine assembly or transmission as doing so may deform the oil pan.
    3. Perform this step while supporting the engine assembly using a sling device and chain block.


55. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

  1. C114267E01
    Put matchmarks on the clutch cover assembly and the flywheel sub-assembly.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the set bolts, and pull off the clutch cover assembly.

    NOTICE:
    Do not drop the clutch disc assembly.


56. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

NOTICE:
Keep the lining part of the clutch disc assembly, the pressure plate and surface of the flywheel sub-assembly away from oil and foreign matter.


57. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

  1. A102137E01
    Using SST, hold the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A109815E02
    Remove the 10 bolts and flywheel sub-assembly.


58. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

  1. A102137E01
    Using SST, hold the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A102156E01
    Remove the 10 bolts, rear drive plate spacer, drive plate and ring gear sub-assembly and front drive plate spacer.


59. REMOVE REAR END PLATE
  1. Remove the bolt and disconnect the No. 1 water by-pass pipe from rear end plate.

  1. Remove the bolt and rear end plate.


60. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
  1. Hold the engine with the engine sling device and chain block.

  1. Remove the 4 bolts from the engine mounting insulator.

  1. Remove the engine assembly by operating the engine sling device and chain block.


61. REMOVE ENGINE WIRE
  1. Remove the engine wire from the engine assembly.


62. INSTALL ENGINE TO ENGINE STAND

NOTICE:
  1. Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
  2. With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.

  1. Install the engine to an engine stand with the bolts.

  1. Remove the 2 bolts and 2 engine hangers.


63. REMOVE PCV PIPE
  1. Remove the bolt and PCV pipe.


64. REMOVE THROTTLE BODY ASSEMBLY

  1. A337883E01
    Disconnect the throttle motor connector.
    Text in Illustration 
    *A
    w/ Dual VVT-i
    *B
    w/o Dual VVT-i

  1. Slide the clamp and disconnect the water by-pass hose from the throttle body assembly.

  1. Slide the clamp and disconnect the No. 2 water by-pass hose from the throttle body assembly.

  1. Remove the 4 bolts and throttle body assembly.

  1. A239457
    Remove the gasket from the intake manifold.


65. REMOVE INTAKE MANIFOLD
  1. Disconnect the vacuum switching valve connector.

  1. Slide the clamp and disconnect the purge line hose from the vacuum switching valve.

  1. A110725
    Detach the 2 wire harness clamps from the wire harness bracket.

  1. Slide the clamp and disconnect the No. 3 PCV hose from the intake manifold.

  1. Slide the clamp and disconnect the vacuum hose from the intake manifold.

  1. A110726
    Remove the bolt and wire harness bracket from the intake manifold.

  1. A337855
    Remove the 5 bolts, 2 nuts and intake manifold.

  1. Remove the gasket from the intake manifold.

  1. Remove the intake manifold insulator from the intake manifold.

  1. w/ Dual VVT-i:

    1. Remove the intake manifold insulator from the intake manifold.


66. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the 4 bolts and 4 ignition coil assemblies.


67. REMOVE SPARK PLUG
  1. Using a 16 mm spark plug wrench, remove the 4 spark plugs.


68. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

NOTICE:
Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.

  1. Disconnect the vacuum hose from the fuel pressure regulator assembly.

  1. Slide the clamp and disconnect the No. 2 fuel hose from the fuel pressure regulator assembly.

  1. A341591E01
    Disconnect the 4 fuel injector connectors.
    Text in Illustration 
    *A
    w/ Dual VVT-i
    *B
    w/o Dual VVT-i

  1. Remove the 2 bolts, fuel pulsation damper assembly and O-ring.

  1. Remove the 2 bolts and fuel delivery pipe sub-assembly together with the 4 fuel injector assemblies.

    NOTICE:
    Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.

  1. Remove the 2 No. 1 delivery pipe spacers from the cylinder head sub-assembly.

  1. Remove the 4 injector vibration insulators.

  1. A341592E01
    Using a screwdriver, pry out the 4 injector spacers and 4 O-rings from the cylinder head sub-assembly.
    Text in Illustration 
    *A
    w/ Dual VVT-i
    *B
    w/o Dual VVT-i
    *a
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.


69. REMOVE FUEL INJECTOR ASSEMBLY

  1. A346727E01
    Pull out the 4 fuel injector assemblies from the fuel delivery pipe sub-assembly.
    Text in Illustration 
    *A
    w/ Dual VVT-i
    *B
    w/o Dual VVT-i
    V100135
    Pull Out

  1. Remove the O-rings from the fuel injector assemblies.


70. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

  1. A113523
    Remove the 4 bolts and the heat insulator No.1.


71. REMOVE NO. 4 INTAKE PIPE

  1. A099544E02
    Remove the 4 nuts and intake pipe No.4.

  1. Remove the 2 gaskets.


72. REMOVE AIR SWITCHING VALVE ASSEMBLY

  1. A264866E01
    w/ Manifold Absolute Pressure Sensor:
    Disconnect the vacuum hose from the air switching valve assembly.

  1. A099545E02
    Disconnect the connector.

  1. Remove the 2 nuts and the switching valve.


73. REMOVE EXHAUST MANIFOLD

  1. A309467
    Remove the 8 nuts, exhaust manifold and gasket.


74. REMOVE FAN PULLEY
  1. Remove the 4 nuts, fan pulley and fan spacer.


75. REMOVE NO. 1 WATER BY-PASS PIPE
  1. Remove the bolt, 2 nuts, No. 1 water by-pass pipe and gasket.


76. REMOVE WATER INLET

  1. A087301
    Remove the 2 nuts, bolt, water inlet and gasket.


77. REMOVE THERMOSTAT

  1. A086841J01
    Remove the thermostat.


78. REMOVE GENERATOR ASSEMBLY

  1. A311548
    Disconnect the generator connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Remove the bolt and disconnect the wire harness clamp.

  1. A311549
    Remove the 3 bolts and generator assembly.


79. REMOVE IDLE PULLEY ASSEMBLY (w/ Air Conditioning System)

  1. A332600
    Loosen the bolt, and then remove the idle pulley assembly.

    HINT:
    The bolt in the illustration cannot be removed from the idle pulley assembly.


80. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

  1. A337819
    Remove the 5 bolts and No. 1 compressor mounting bracket.


81. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

  1. A102170
    Remove the bolt, collar and No. 1 idler pulley sub-assembly.


82. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A232341
    Remove the 2 bolts and V-ribbed belt tensioner assembly.


83. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

  1. A102133
    Using a 24 mm deep socket wrench, remove the engine oil pressure switch assembly.


84. REMOVE KNOCK CONTROL SENSOR

  1. G037712E01
    Disconnect the knock control sensor connector.

  1. Remove the bolt and the knock control sensor.


85. REMOVE ENGINE COOLANT TEMPERATURE SENSOR
  1. Disconnect the engine coolant temperature sensor connector.

  1. A102134
    Using a 19 mm deep socket wrench, remove the engine coolant temperature sensor and gasket.


86. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

HINT:
Perform this procedure only when replacement of the front No. 1 engine mounting bracket RH is necessary.

  1. A102168
    Remove the 4 bolts and front No. 1 engine mounting bracket RH.


87. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

HINT:
Perform this procedure only when replacement of the front No. 1 engine mounting bracket LH is necessary.

  1. A102169
    Remove the 4 bolts and front No. 1 engine mounting bracket LH.


88. REMOVE ENGINE OIL LEVEL SENSOR
  1. Remove the 4 bolts and engine oil level sensor.

← COMPONENTS (from Jan 2015)REMOVAL (Apr 2016 – Dec 2016) →