2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Oct 2014

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.


1. INSTALL TIMING GEAR CASE ASSEMBLY
  1. Install 2 new O-rings.

  1. Remove any old seal packing (FIPG material).

  1. A059946E03
    Install the driven rotor to the timing gear case with the mark facing the cylinder block side.

  1. Install a new gasket to the groove of the timing gear case.

  1. A100875E04
    Apply seal packing to the timing gear case as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal packing diameter:
    4.0 mm (0.16 in.)

    NOTICE:
    Install the timing gear case within 3 minutes and tighten the bolts within 15 minutes of applying FIPG.

  1. A069841E01
    Align the "2" marks of the No. 1 balanceshaft driven gear with the one on the oil pump drive gear.

  1. Align the mark on the oil pump drive gear with the mark on the timing gear case.

  1. A100878E01
    Install the timing gear case with the union bolt and 8 bolts.

    Torque:
    for union bolt (A):
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }
    for bolt:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Remove the screw plug and gasket.

  1. A102910
    Pour approximately 50 cc (3.05 cu in.) of engine oil into the oil pump.

  1. Install a new gasket and the screw plug.

    Torque:
    41 N*m{ 418 kgf*cm , 30 ft.*lbf }


2. INSTALL CRANKSHAFT TIMING GEAR

  1. A100881E02
    Position the crankshaft timing gear with timing mark "1" facing outward.

  1. Align the key groove of the crankshaft timing gear with the set key on the crankshaft.

  1. Using SST and a hammer, tap on the timing gear to install it.

    SST
    09223-00010  


3. INSTALL INJECTION GEAR
  1. Install a new O-ring and the fuel supply pump with the 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Temporarily install the injection gear with the nut.

    HINT:
    Fit the key (protrusion) of the fuel supply pump into the key slot of the injection gear.

  1. A069843E01
    Align the "3" marks of the No. 2 balanceshaft driven gear with the one on the injection gear.

  1. A069844E01
    Install a new O-ring to the injection gear.

  1. Install the injection gear set nut.

  1. A100864E01
    Using SST, tighten the nut.
    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }


4. INSTALL NO. 1 IDLE GEAR SHAFT

  1. A069846E02
    Apply a coat of engine oil to the No. 1 idle gear shaft.

  1. A060159E01
    Install the No. 1 idle gear shaft as shown in the illustration.


5. INSTALL NO. 1 IDLE GEAR

  1. A100886E02
    Align the "5" timing marks of the No. 1 idle gear and crankshaft timing gear.

  1. Using SST, turn the injection gear and align the "4" timing marks of the No. 1 idle gear and injection gear, and then mesh the gears.

    SST
    09960-10010   (09962-01000, 09963-01000)


6. INSTALL IDLE GEAR THRUST PLATE

  1. A060161E02
    Position the thrust plate with the protrusion facing forward.

  1. Align the bolt holes, and then install the thrust plate with the 2 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Remove the service bolt.


7. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
  1. Align the key groove of the sensor plate with the set key.

  1. Install the sensor plate with the cupped side facing outward.


8. INSTALL TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL

  1. A102765E01
    Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.
    SST
    09649-17010  
    09950-70010   (09951-07100)

    Oil seal protrusion from the flat-end surface:
    0 to 0.5 mm (0 to 0.020 in.)

  1. Apply MP grease to the oil seal lip.

    NOTICE:
    Keep the lip clean. Prevent dirt and dust from adhering to the oil seal lip.


9. INSTALL TIMING CHAIN OR BELT COVER OIL SEAL

  1. A102764E01
    Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.
    SST
    09608-32010  
    09950-70010   (09951-07100)

    Oil seal protrusion from the flat-end surface:
    0 to 0.5 mm (0 to 0.020 in.)

  1. Apply MP grease to the oil seal lip.

    NOTICE:
    Keep the lip clean. Prevent dirt and dust from adhering to the oil seal lip.


10. INSTALL TIMING GEAR COVER
  1. Remove any old seal packing (FIPG material).

  1. A110888E04
    Apply seal packing to the timing gear cover as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal packing diameter:
    4.0 mm (0.16 in.)

    NOTICE:
    After applying seal packing, install the timing gear cover within 3 minutes and tighten the bolts within 15 minutes.

  1. Install a new O-ring to the timing gear case.

  1. Install the timing gear case with the 14 bolts and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


11. INSTALL OIL STRAINER SUB-ASSEMBLY
  1. Install a new gasket and the oil strainer with the 2 bolts and 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


12. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old packing (FIPG material).

  1. A219033E01
    Apply seal packing to a new cylinder block stiffening plate as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal packing diameter:
    4.0 mm (0.16 in.)

    NOTICE:
    Install the oil pan within 3 minutes and tighten the bolts within 15 minutes of applying FIPG.

  1. A243033E01
    Apply seal packing to the oil pan as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal packing diameter:
    4.0 mm (0.16 in.)

    NOTICE:
    Install the oil pan within 3 minutes and tighten the bolts within 15 minutes of applying FIPG.

  1. Install the oil pan with the 22 bolts and 2 nuts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


13. INSTALL ENGINE OIL LEVEL SENSOR
  1. Install a new gasket to the engine oil level sensor.

  1. Install the engine oil level sensor with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the engine oil level sensor connector.


14. INSTALL CRANKSHAFT PULLEY
  1. Align the pulley set key with the key groove of the pulley and install the pulley.

  1. A142434E01
    Using SST, install the pulley bolt.
    SST
    09213-58014  
    09330-00021  

    Torque:
    365 N*m{ 3722 kgf*cm , 269 ft.*lbf }


15. INSTALL WATER PUMP ASSEMBLY
  1. Install a new gasket and the water pump with the 5 bolts and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


16. INSTALL NO. 2 TIMING BELT COVER

A060279E01
  1. Apply seal packing (FIPG) to the areas shown in the illustration.

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    After applying FIPG, install the No. 2 timing belt cover within 3 minutes and tighten the bolts and nut within 15 minutes.

  1. Clean the bolts and their holes.

  1. Apply adhesive to 2 or 3 threads at the end of 4 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the No. 2 timing belt cover with the 4 bolts and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


17. INSTALL CAMSHAFT TIMING PULLEY

  1. A060182E01
    Install the camshaft timing pulley.

  1. Install the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

    Torque:
    98 N*m{ 1000 kgf*cm , 72 ft.*lbf }


18. INSTALL INJECTOR ASSEMBLY
(Click here)

19. INSTALL FUEL SUPPLY PUMP ASSEMBLY
(Click here)

20. INSTALL COMMON RAIL ASSEMBLY
(Click here)

21. INSTALL EGR COOLER ASSEMBLY
(Click here)

22. INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY
(Click here)

23. INSTALL DIESEL THROTTLE BODY ASSEMBLY
  1. Install a new gasket and the diesel throttle body with the 2 bolts and 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 diesel throttle body connectors.

  1. w/o DPF:

    1. Install the wire harness clamp with the bolt.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    2. Connect the diesel turbo pressure sensor connector and vacuum switching valve connector.


24. INSTALL CAMSHAFT POSITION SENSOR

A102907
  1. Apply a light coat of engine oil to the O-ring of the camshaft position sensor.

  1. A102283
    Install the camshaft position sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Do not crack or jam the O-ring when installing the camshaft position sensor.

  1. Connect the camshaft position sensor connector.


25. INSTALL CRANKSHAFT POSITION SENSOR

A102906
  1. Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.

  1. A151576
    Install the crankshaft position sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Do not crack or jam the O-ring when installing the crankshaft position sensor.

  1. Connect the 3 wire harness clamps.

  1. A102284
    Connect the crankshaft position sensor to the No. 1 vacuum pipe.

  1. Connect the crankshaft position sensor connector.


26. INSTALL TIMING BELT
(Click here)

27. INSTALL VACUUM PUMP ASSEMBLY
  1. Install 2 new O-rings to the vacuum pump.

  1. Install the vacuum pump with the 2 nuts.

    Torque:
    21 N*m{ 210 kgf*cm , 15 ft.*lbf }


28. INSTALL TIMING GEAR COVER INSULATOR
  1. Install the timing gear cover insulator with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


29. INSTALL VANE PUMP ASSEMBLY
  1. Install a new vane pump O-ring to the vane pump assembly.

  1. C101372E01
    Install the vane pump assembly with the 2 nuts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    NOTICE:
    Make sure that the vane pump O-ring is not caught between other parts.


30. REMOVE ENGINE STAND

31. INSTALL ENGINE ASSEMBLY
(Click here)
← INSPECTION (from Oct 2014)COMPONENTS (from Oct 2014) →