2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 from Apr 2016

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.


1. INSTALL TIMING GEAR CASE ASSEMBLY
  1. Remove any old seal packing (FIPG material).

  1. A262961E01
    Apply seal packing to the timing gear case as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    4 mm (0.16 in.)

    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF
    *1
    Seal Packing

    NOTICE:
    After applying seal packing, install the timing gear case assembly within 3 minutes and tighten the bolts within 15 minutes.

  1. A060151E04
    Install a new gasket to the groove of the timing gear case.
    Text in Illustration 
    *1
    New Gasket

  1. Install 2 new O-rings.

  1. A069841E01
    Align the "2" marks of the No. 1 balanceshaft driven gear and oil pump drive gear.

  1. Align the mark on the oil pump drive gear with the mark on the timing gear case.

  1. A262963
    w/ DPF:
    Install the timing gear case with the union bolt and 8 bolts.

    Torque:
    for bolt A:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }
    for bolt B:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for union bolt:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B
    V100137
    Union bolt

  1. A262962
    w/o DPF:
    Install the timing gear case with the union bolt and 8 bolts.

    Torque:
    for bolt:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }
    for union bolt:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    Text in Illustration 
    V100135
    Bolt
    V100136
    Union bolt

  1. A060154E01
    Remove the screw plug and gasket.

  1. Pour approximately 50 cc (3.05 cu. in.) of engine oil into the oil pump.

  1. Install a new gasket and the screw plug.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


2. INSTALL INJECTION GEAR
  1. Install a new O-ring and the fuel supply pump with the 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Temporarily install the injection gear with the nut.

    HINT:
    Make sure that the key slot of the injection gear fits over the key (protrusion) of the supply pump.

  1. A069843E01
    Align the "3" marks of the No. 2 balanceshaft driven gear and injection gear.

  1. A069844E02
    Install a new O-ring to the injection gear.
    Text in Illustration 
    *1
    New O-Ring

  1. A069845E01
    Temporarily install the injection gear set nut.

  1. Using SST, tighten the nut.

    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }


3. INSTALL CRANKSHAFT TIMING GEAR

  1. A061827E01
    Position the crankshaft timing gear with the "1" timing marks facing forward.

  1. Align the key groove of the crankshaft timing gear with the set key on the crankshaft.

  1. Using SST and a hammer, tap on the timing gear to install it.

    SST
    09223-00010  


4. INSTALL NO. 1 IDLE GEAR SHAFT

  1. A069846E01
    Apply a coat of engine oil to the No. 1 idle gear shaft.
    Text in Illustration 
    *1
    Engine Oil

  1. A060159E07
    Install the No. 1 gear shaft as shown in the illustration.
    Text in Illustration 
    *1
    Oil Hole


5. INSTALL NO. 1 IDLE GEAR

  1. A069847E03
    Mount the No. 1 idle gear in a vise.
    Text in Illustration 
    *1
    Cutout Mark

    HINT:
    Make sure the cutout mark of the idle gear faces down.

    NOTICE:
    Be careful not to damage the gear.

  1. A069848E03
    Install the idle gear spring.
    Text in Illustration 
    *1
    Wave Washer
    *2
    No. 2 Idle Sub Gear
    *3
    Idle Gear Spring

  1. Install the No. 2 idle sub gear.

  1. Install the wave washer.

    HINT:
    Fit the pins on the gears between the spring ends.

  1. Using snap ring pliers, install the shaft snap ring.

  1. A069850E03
    Using SST, align the holes of the No. 1 idle gear and No. 2 idle sub gear by turning the No. 2 idle sub gear clockwise, and install a service bolt.
    SST
    09960-10010   (09962-01000, 09963-00700)
    Text in Illustration 
    *1
    Service Bolt

  1. Remove the No. 1 idle gear from the vise and turn it upside down.

  1. A069851E03
    Mount the No. 1 idle gear and No. 2 idle sub gear in a vise.
    Text in Illustration 
    *a
    Upward

    NOTICE:
    Be careful not to damage the gears.

  1. A069852E02
    Remove the service bolt.
    Text in Illustration 
    *1
    Service Bolt

  1. A069853E03
    Install the idle gear spring.
    Text in Illustration 
    *1
    Wave Washer
    *2
    No. 1 Idle Sub Gear
    *3
    Idle Gear Spring

  1. Install the No. 1 idle sub gear.

  1. Install the wave washer.

    HINT:
    Fit the pins on the gears between the spring ends.

  1. Using snap ring pliers, install the snap ring.

  1. A069854E03
    Using SST, align the holes of the No. 1 idler gear and No. 1 idle sub gear by turning the No. 1 idle sub gear clockwise, and install a service bolt.
    SST
    09960-10010   (09962-01000, 09963-00600)
    Text in Illustration 
    *1
    Service Bolt
    *a
    Upward

  1. G036757E04
    Align the "5" timing marks of the idle gear and crankshaft timing gear.
    Text in Illustration 
    *a
    Turn

  1. Using SST, turn the injection gear and align the "4" timing marks of the idle gear and injection gear, and then mesh the gears.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. A222334E02
    Position the thrust plate with the protrusion facing forward.
    Text in Illustration 
    *1
    Service Bolt

  1. Align the bolt holes and install the thrust plate with the 2 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Remove the service bolt.


6. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
  1. Align the key groove of the No. 1 crankshaft position sensor plate with the set key.

  1. Install the No. 1 crankshaft position sensor plate with the cupped side facing outward.

    HINT:
    When replacing the No. 1 crankshaft position sensor plate, perform "Crank Time Compensation Reset" (w/ DPF: Click here, w/o DPF: Click here).


7. INSTALL TIMING GEAR COVER OIL SEAL

HINT:
There are 2 methods to remove the oil seal.

  1. If the timing gear cover is removed from the cylinder block:

    1. A058121E01
      Using a screwdriver and hammer, tap out the oil seal.

    2. A058119E01
      Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.
      SST
      09214-76011  

    3. Apply MP grease to the lip of the oil seal.

  1. If the timing gear cover is installed to the cylinder block:

    1. A058124E01
      Using SST, remove the oil seal.
      SST
      09308-10010  
      09950-40011   (09957-04010)
      09950-60010   (09951-00350)

    2. A058125E01
      Apply MP grease to the lip of a new oil seal.

    3. Using SST and a hammer, tap in the oil seal until its surface is flush with the timing gear cover edge.

      SST
      09214-76011  


8. INSTALL TIMING GEAR CASE OIL SEAL

HINT:
There are 2 methods to remove the oil seal.

  1. If the timing gear cover is removed from the cylinder block:

    1. A058117E01
      Using a screwdriver and hammer, tap out the oil seal.

    2. A058118E02
      Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.
      SST
      09223-15020  
      09502-12010  
      09950-70010   (09951-07100)

    3. Apply MP grease to the lip of the oil seal.

  1. If the timing gear cover is installed to the cylinder block:

    1. A058126E02
      Using a knife, cut through the lip of the oil seal.

    2. Using a screwdriver, pry out the oil seal.

      NOTICE:
      Be careful not to damage the crankshaft.

    3. A058127E01
      Apply MP grease to the lip of the oil seal.

    4. Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.

      SST
      09223-15020  
      09502-12010  
      09950-70010   (09951-07100)


9. INSTALL TIMING GEAR COVER
  1. Remove any old seal packing (FIPG material).

  1. A262964E01
    Apply seal packing to the timing gear cover as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    4 mm (0.16 in.)

    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF
    *1
    Seal Packing

    NOTICE:
    Install the timing gear cover within 3 minutes and tighten bolts within 15 minutes of applying seal packing.

  1. A239295
    w/ DPF:
    Install 3 new O-rings to the timing gear case.

  1. A060162E02
    w/o DPF:
    Install a new O-ring to the timing gear case.
    Text in Illustration 
    *1
    New O-Ring

  1. Install the timing gear cover with the 14 bolts and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


10. INSTALL OIL STRAINER SUB-ASSEMBLY
  1. Install a new gasket and the oil strainer with the 2 bolts and 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


11. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old seal packing (FIPG material).

  1. A100880E05
    Apply seal packing to the oil pan as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    4.0 mm (0.16 in.)

    NOTICE:
    Install the oil pan within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

  1. A219033E03
    w/o DPF:
    Apply seal packing to the cylinder block stiffening plate as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    4.0 mm (0.16 in.)

    NOTICE:
    Install the cylinder block stiffening plate within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

  1. w/ DPF:
    Install the oil pan with the 22 bolts and 2 nuts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. w/o DPF:
    Install the cylinder block stiffening plate and oil pan with the 22 bolts and 2 nuts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


12. INSTALL CRANKSHAFT PULLEY
  1. Align the keyway of the pulley with the key located on the crankshaft, and then slide the pulley into place to install it.

  1. A142434E01
    Using SST, install the pulley bolt.
    SST
    09213-58014  
    09330-00021  

    Torque:
    365 N*m{ 3722 kgf*cm , 269 ft.*lbf }


13. INSTALL WATER PUMP ASSEMBLY
  1. Install a new gasket and the water pump with the 5 bolts and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


14. INSTALL NO. 2 TIMING BELT COVER

A060279E01
  1. Apply seal packing (FIPG) to the areas shown in the illustration.

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    After applying FIPG, install the No. 2 timing belt cover within 3 minutes and tighten the bolts and nut within 15 minutes.

  1. Clean the bolts and their holes.

  1. Apply adhesive to 2 or 3 threads at the end of 4 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the No. 2 timing belt cover with the 4 bolts and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


15. INSTALL CAMSHAFT TIMING PULLEY

  1. A060182E01
    Install the camshaft timing pulley.

  1. Install the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

    Torque:
    98 N*m{ 1000 kgf*cm , 72 ft.*lbf }


16. INSTALL INJECTOR ASSEMBLY
(Click here)

17. INSTALL FUEL SUPPLY PUMP ASSEMBLY
(Click here)

18. INSTALL COMMON RAIL ASSEMBLY
(Click here)

19. INSTALL EGR COOLER WITH NO. 2 EGR VALVE ASSEMBLY
(Click here)

20. INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY
(Click here)

21. INSTALL DIESEL THROTTLE BODY ASSEMBLY
(Click here)

22. INSTALL OIL PRESSURE SWITCHING VALVE ASSEMBLY

  1. A239526E02
    Apply a light coat of engine oil to the O-ring of the oil pressure switching valve.

  1. Install the oil pressure switching valve with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Make sure that the O-ring is not cracked or jammed when installing the oil pressure switching valve.

  1. Connect the oil pressure switching valve connector.


23. INSTALL CAMSHAFT POSITION SENSOR

A102907
  1. Apply a light coat of engine oil to the O-ring of the camshaft position sensor.

  1. A102283
    Install the camshaft position sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Do not crack or jam the O-ring when installing the camshaft position sensor.

  1. Connect the camshaft position sensor connector.


24. INSTALL CRANKSHAFT POSITION SENSOR

  1. A231924
    Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.

  1. TYPE A:

    A307645E01

    Text in Illustration 
    *1
    Clamp
    *2
    Protrusion
    *3
    Wire Harness Clamp (A)
    *4
    Wire Harness Clamp (B)
    *5
    Wire Harness Clamp (C)
    -
    -

    1. Install the wire harness clamp (A) to the crankshaft position sensor connector.

    2. Install the crankshaft position sensor with the bolt.

      Torque:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

      NOTICE:
      Make sure that the O-ring is not damaged or does not jump out of position during installation.

    3. Install a new clamp.

      NOTICE:
      1. Make sure that no portion of the clamp remains in the clamp installation hole. If there is any portion of the clamp remaining, remove it.
      2. Make sure the crankshaft position sensor wire harness is installed in the position shown in the illustration.

    4. Attach the crankshaft position sensor connector to the No. 1 vacuum transmitting pipe.

    5. Connect the crankshaft position sensor connector.

    6. Attach the 2 wire harness clamps (B, C).

  1. TYPE B:

    A307643E01

    Text in Illustration 
    *1
    Clamp
    *2
    Protrusion
    *3
    Bracket (Clamp)
    *4
    Wire Harness Clamp (A)
    *5
    Wire Harness Clamp (B)
    *6
    Wire Harness Clamp (C)

    1. Install the wire harness clamp (A) to the crankshaft position sensor connector.

    2. Install the crankshaft position sensor with the bolt.

      Torque:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

      NOTICE:
      Make sure that the O-ring is not damaged or does not jump out of position during installation.

    3. Install the bracket (clamp) with the bolt.

      Torque:
      13 N*m{ 132 kgf*cm , 9.5 ft.*lbf }

    4. Install a new clamp.

      NOTICE:
      1. Make sure that no portion of the clamp remains in the clamp installation hole. If there is any portion of the clamp remaining, remove it.
      2. Make sure the crankshaft position sensor wire harness is installed in the position shown in the illustration.

    5. Attach the crankshaft position sensor connector to the No. 1 vacuum transmitting pipe.

    6. Connect the crankshaft position sensor connector.

    7. Attach the 2 wire harness clamps (B, C).

    8. Attach the 2 wire harness clamps to the bracket (clamp).


25. INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY
  1. Using a 10 mm hexagon wrench, install a new washer and the No. 1 timing belt idler with the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }


26. INSTALL TIMING BELT
(Click here)

27. INSTALL VACUUM PUMP ASSEMBLY
  1. Install 2 new O-rings and the vacuum pump with the 2 nuts.

    Torque:
    21 N*m{ 210 kgf*cm , 15 ft.*lbf }


28. INSTALL VANE PUMP ASSEMBLY
  1. Install a new vane pump O-ring to the vane pump assembly.

  1. C101372E01
    Install the vane pump assembly with the 2 nuts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    NOTICE:
    Make sure that the vane pump O-ring is not caught between other parts.


29. REMOVE ENGINE STAND
  1. Remove the engine from the engine stand.


30. INSTALL ENGINE ASSEMBLY
(Click here)
← INSTALLATION (Oct 2014 – Dec 2014)INSTALLATION (from Apr 2016) →