INSTALLATION
Removal / installation · Vehicles built from Jan 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
| 1. INSTALL CAMSHAFT |
Set the crankshaft to 90° position from the TDC/compression.

Place the camshaft to the cylinder head as shown in the illustration.

- NOTICE:
- Apply engine oil to the cams, thrusts and gears of the camshaft as well as on the journal of the cylinder head.
Align the dot marks of the camshaft and No.2 camshaft by meshing the both gears before placing the No.2 camshaft.

Remove old packing (FIPG) from the camshaft bearing cap.
Apply seal packing to the specific places shown in the illustration.

- Seal packing:
- Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
- Thickness:
- 1 mm (0.04 in.)
- NOTICE:
- Be careful not to adhere FIPG to the oil passage of the bearing cap.
- After applying FIPG, install the camshaft bearing cap within 3 minutes and then tighten its bolts within 15 minutes.
- Do not start the engine 2 hours after the installation.
- Be careful not to adhere FIPG to the oil passage of the bearing cap.
Install the camshaft bearing cap as shown in the illustration.

Tighten the 15 bolts for the camshaft bearing cap in the specified order shown in the illustration.
- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
Adjust and inspect valve clearance.
Fix the timing belt cover No.2 with the 4 bolts and nuts.
- Torque:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
Tighten the bolt for the camshaft timing pulley while holding the camshaft with a monkey wrench.
- Torque:
- 98 N*m{ 1,000 kgf*cm , 72 ft.*lbf }
Adjust and inspect the valve clearance. (Click here)
Remove the camshaft timing pulley and timing belt cover No.2.
| 2. INSTALL CAMSHAFT SETTING OIL SEAL |
Apply a bit of MP grease to a new oil seal's lip.
- NOTICE:
- Keep the lip clean. Do not to bring dirt and dust on that area.
Using SST and a hammer, fit the oil seal.

- SST
- 09608-06041
- Oil seal depth from flat end face:
- 0.5 to 1.5 mm (0.020 to 0.060 in.)
- NOTICE:
- Install the oil seal straight.
| 3. INSTALL INJECTOR ASSEMBLY |
| 4. CHECK NOZZLE LEAKAGE PIPE LEAK |
| 5. INSTALL TIMING BELT COVER NO.2 |
Remove old seal packing (FIPG) from the timing gear case.

Apply seal packing to the specific places shown in the illustration.
- Seal packing:
- Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
- NOTICE:
- After applying FIPG, install the timing belt No.2 cover within 3 minutes and tighten its bolts and nuts within 15 minutes.
- Do not start the engine 2 hours after the installation.
- After applying FIPG, install the timing belt No.2 cover within 3 minutes and tighten its bolts and nuts within 15 minutes.
Fix the timing belt cover No.2 with the 4 bolts and nuts.
- Torque:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
| 6. INSTALL TIMING BELT IDLER SUB-ASSEMBLY NO.1 |
Using a 10 mm socket hexagon wrench, install the new plate washer and timing belt idler No.1.

- Torque:
- 35 N*m{ 357 kgf*cm , 26 ft.*lbf }
| 7. INSTALL CAMSHAFT TIMING PULLEY |
Install the camshaft timing pulley.

Tighten the bolt for the camshaft timing pulley while holding the camshaft with a monkey wrench.
- Torque:
- 98 N*m{ 1,000 kgf*cm , 72 ft.*lbf }
| 8. PISTON AND VALVE BREAK PREVENT WORK |
When turning the camshaft with the timing belt removed, turn the crankshaft 90° counterclockwise.

- NOTICE:
- When installing the timing belt, it is necessary to return the camshaft to the timing marks and then turn the crankshaft clockwise so that it aligns with the timing marks as shown in the illustration.
| 9. INSTALL TIMING BELT |
Check that the timing marks are aligned as shown in the illustration.

Install the timing belt to pump drive shaft pulley, camshaft timing pulley and timing belt idler No.1 in sequence.
Set the tensioner to the press upright.

- NOTICE:
- Do not allow the rod end to scratch and deform.
- Press the tensioner rod in upward.
- Protect a tip of the push rod with a rag in order to prevent damage.
- Do not allow the rod end to scratch and deform.
Using a press, slowly apply 981 to 9,807 N (100 to 1,000 kgf, 220 to 2,205 lbf) of force to the push rod.
- NOTICE:
- Do not apply loads 981 to 9,807 N (100 to 1,000 kgf, 220 to 2,205 lbf) or more on the push rod.
Align the holes of push rod and housing, pass a 1.27 mm hexagon wrench through the holes to keep the setting position of the push rod.
Temporarily install the timing belt tensioner with the 2 bolts while pushing the idler pulley toward the timing belt.
Tighten the 2 bolts.
- Torque:
- 13 N*m{ 133 kgf*cm , 10 ft.*lbf }
- NOTICE:
- Uniformly tighten the 2 bolts and install the tensioner
Remove the 1.5 mm hexagon wrench from the tensioner.
Turn the crankshaft in the clockwise direction twice, check that the timing marks are aligned as shown in the illustration.

| 10. INSTALL TIMING BELT COVER NO.1 |
Install the timing belt No.1 cover with the 6 bolts.

- Torque:
- 6.0 N*m{ 61 kgf*cm , 53 in.*lbf }
Install the wire harness clamp.
| 11. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
Install 4 new No. 3 cylinder head cover gaskets to the cylinder head cover as shown in the illustration.

- NOTICE:
- Do not install the gaskets at an angle.
- Keep the lip of the gasket free from foreign materials.
- Do not install the gaskets at an angle.
Install a new cylinder head cover gasket to the cylinder head cover.
Remove old seal packing (FIPG) from the cylinder head.
Apply a seal packing to the specific places described in the illustration.

- Seal packing:
- Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
- NOTICE:
- After applying the seal packing, parts must be assembled within 3 minutes, and then tighten within 15 minutes.
- Otherwise the material must be removed and reapplied.
- Do not start the engine 2 hour after the installation.
- After applying the seal packing, parts must be assembled within 3 minutes, and then tighten within 15 minutes.
Install the cylinder head cover with 10 bolts and 2 nuts.
- Torque:
- 9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
Connect the ventilation hose.
Install a new nozzle holder seal.
| 12. INSTALL INJECTION PIPE |
- SST
- 09023-12701
- NOTICE:
- When replacing the fuel injector, common rail, or cylinder head with a new one, replace injection pipes No. 1, No. 2, No. 3, and No. 4.
- Keep clean the joint of the injection pipe.
- When replacing the fuel injector, common rail, or cylinder head with a new one, replace injection pipes No. 1, No. 2, No. 3, and No. 4.
Install the injection pipes.
Temporarily install the 4 injection pipes.

Install the injection pipe clamp No.3 in 2 nuts.

- Torque:
- 5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
Fasten the union sequentially, from the injection pipe common rail to the injector, using SST.

- SST
- 09023-12701
- Torque:
- Use union nut wrench and torque wrench:
- 32 N*m{ 326 kgf*cm , 24 ft.*lbf }
| 13. INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY |
Install the vane pump oil reservoir assembly with the 2 bolts.

- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
| 14. INSTALL FAN & GENERATOR V BELT |
Rotate the V-ribbed belt tensioner pulley clockwise, and then install the fan and generator V belt.
- NOTICE:
- Make sure that the fan and generator V belt is set properly on each pulley.
Check that the indicator mark of the V-ribbed belt tensioner (Click here).
| 15. INSTALL ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY |
Install the engine service hole sub cover with the 5 bolts.
- Torque:
- 13 N*m{ 133 kgf*cm , 10 ft.*lbf }
| 16. INSTALL FRONT DOOR SCUFF PLATE RH |
| 17. INSTALL FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type) |
Perform the same procedure as above on the opposite side. (Click here)
| 18. INSTALL FRONT SEAT ASSEMBLY RH (for Low-back Seat Type) |
Perform the same procedure as above on the opposite side. (Click here)
| 19. CONNECT BATTERY NEGATIVE TERMINAL |
| 20. ADD ENGINE COOLANT |
Firmly tighten the drain plugs.
Fill the radiator reservoir assembly with engine coolant to the top of the inlet.
- Standard Capacity:
Item
Specified Condition
w/o Heater
13.2 liters (13.9 US qts, 11.6 Imp. qts)
w/ Front Heater
14.2 liters (15.0 US qts, 12.5 Imp. qts)
w/ Front and Rear Heaters
16.2 liters (17.1 US qts, 14.3 Imp. qts)
- NOTICE:
- Do not substitute plain water for engine coolant.
- HINT:
- Use of improper coolants may damage the engine cooling system.
- Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- Use of improper coolants may damage the engine cooling system.
Loosen the bleeder plug of the outlet housing.
When air is bled and the engine coolant drains out, firmly tighten the bleeder plug.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Add engine coolant up to the B line mark in the radiator reservoir assembly and install the radiator reservoir cap sub-assembly.

Warm up the engine until the thermostat opens.
While the thermostat is open, circulate the engine coolant for several minutes.
- HINT:
- The thermostat open timing can be confirmed by pressing the No. 3 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.
After the engine cools down, check that the engine coolant level is between the LOW and FULL level marks.

| 21. BLEED FUEL LINE |
Push the priming pump for several times to fill up the fuel lines with fuel.
| 22. CHECK FUEL LEAK |
PERFORM ACTIVE TEST
Connect the GTS to the DLC3.
Turn the ignition switch on.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test.
Tester Display
Test Details
Control Range
Diagnostic Notes
Test the Fuel Leak
Pressurizes common rail internal fuel pressure, and checks for fuel leaks
Stop/Start
- Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when ON is selected
- Above conditions preserved while test is ON
- Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when ON is selected
| 23. CHECK FOR ENGINE OIL LEAKS |
| 24. CHECK FOR ENGINE COOLANT LEAKS |
- CAUTION:
- Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Fill the radiator with coolant and attach a radiator cap tester to the radiator.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 137 kPa (1.4 kgf/cm2, 19.9 psi), and check that the pressure does not drop.
- HINT:
- If the pressure drops, check the hoses, radiator or water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 25. INSTALL ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1) |
- Torque:
- 13 N*m{ 133 kgf*cm , 10 ft.*lbf }
| 26. CHECK IDLE SPEED |
- NOTICE:
- This checking procedure should be done under the following condition.
- HINT:
- Regarding the details about the intelligent tester, refer to its operator's manual.
- If the intelligent tester is not available, a tachometer's tester probe can substitute for it.
- Regarding the details about the intelligent tester, refer to its operator's manual.
Connect the intelligent tester to the DLC3.
If the tester is not available, connect a tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.

- SST
- 09843-18030
Start the engine and check the idle speed.
- Idle speed:
- 700 to 800 rpm
- HINT:
- If the idle speed is not as specified, check by troubleshooting in the diagnostics section.
In case of the tester probe of the tachometer is connected to the DLC3, disconnect the tester probe from terminal 9 of the DLC3 with SST.
Disconnect the intelligent tester from the DLC3.
| 27. INSPECT MAXIMUM ENGINE SPEED |
- NOTICE:
- This checking procedure should be done under the following condition.
- HINT:
- Regarding the details about the intelligent tester, refer to its operator's manual.
- If the intelligent tester is not available, a tachometer's tester probe can substitute for it.
- Regarding the details about the intelligent tester, refer to its operator's manual.
Connect the intelligent tester to the DLC3.
If the tester is not available, connect a tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.

- SST
- 09843-18030
Start the engine.
Depress the accelerator pedal all the way to the limit.
Check the maximum speed.
- Maximum speed:
- 4500 to 4700 rpm
- HINT:
- If the maximum speed is not as specified, check by troubleshooting in the diagnostics section.
In case of the tester probe of the tachometer is connected to the DLC3, disconnect the tester probe from terminal 9 of the DLC3 with SST.
Disconnect the intelligent tester from the DLC3.
| 28. PERFORM INITIALIZATION |
