2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Oct 2014


1. INSTALL ENGINE REAR OIL SEAL

  1. A253830E01
    Using SST and a hammer, tap in a new oil seal.
    SST
    09518-36030  
    09950-70010   (09951-07200)

    Acceptable depth from the top flat face of the oil seal retainer:
    0 to 0.5 mm (0 to 0.020 in.)

    NOTICE:
    Be sure to make the oil seal horizontal when embedded.

  1. Apply a bit of MP grease to the oil seal's lip.

    NOTICE:
    Keep the lip clean. Do not bring dirt or dusts on that area.


2. INSTALL ENGINE REAR OIL SEAL RETAINER

  1. A075507E02
    Remove oil seal packing (FIPG) from oil pan and cylinder block.

  1. Apply a seal packing to the specific places described in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. After applying FIPG install the engine rear oil seal retainer within 3 minutes and then tighten its bolts within 15 minutes.
    2. Do not start the engine 2 hours after the installation.

  1. A072856E01
    Install the engine rear oil seal retainer with the 7 bolts.

    Torque:
    Bolt A:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }
    Bolt B:
    16 N*m{ 166 kgf*cm , 12 ft.*lbf }


3. INSTALL REAR END PLATE
  1. Install the rear end plate with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


4. INSTALL FLYWHEEL SUB-ASSEMBLY

  1. A072424E01
    Fix the crankshaft with SST.
    SST
    09213-58013  
    09330-00021  

  1. A054047E02
    Apply adhesive to 2 or 3 threads of the 8 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. A102803E01
    For manual transmission

    1. Install the flywheel with the 8 bolts.

      Torque:
      178 N*m{ 1,815 kgf*cm , 131 ft.*lbf }

  1. For automatic transmission.

    1. Install the flywheel, drive plate and drive plate spacer rear with the 8 bolt.

      Torque:
      178 N*m{ 1,815 kgf*cm , 131 ft.*lbf }


5. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

  1. C104159E01
    Insert SST into the clutch disc assembly, then insert them into the flywheel sub-assembly.
    SST
    09301-00110  

    NOTICE:
    Take care not to insert the clutch disc assembly in the wrong direction.


6. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

  1. C114265E02
    Align the matchmarks on the clutch cover assembly with the one on the flywheel sub-assembly.

  1. Following the procedures shown in the illustration, tighten the 6 bolts starting from the bolt located near the knock pin on the top.

    SST
    09301-00110  

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

    HINT:
    1. Evenly tighten the bolts by following the order shown in the illustration.
    2. Tighten the bolts after checking that the disc is in the center by lightly moving the SST up and down, left and right.


7. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)

  1. C086210
    Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

    Maximum non-alignment:
    1.3 mm (0.051 in.)

  1. C114266E01
    If alignment is not as specified, adjust the diaphragm spring tip alignment using SST.
    SST
    09333-00013  


8. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)

9. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
(Click here)
← REMOVAL (from Oct 2014)COMPONENTS (from Oct 2014) →