2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Oct 2014


1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Air Conditioning System)
  1. Start up the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor at an engine rpm of approximately 1,000 for 5 to 6 minutes to circulate the refrigerant and collect compressor oil remaining in each component into the cooler compressor as much as possible.

  1. Stop the engine.

  1. Using SST, let the refrigerant gas out.

    SST
    07110-58060   (07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)


2. DRAIN ENGINE COOLANT

A316990E01

CAUTION:
To avoid the danger of being burned, do not remove the reservoir cap while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain plug.

  1. Remove the reservoir cap.

  1. Loosen the cylinder block drain plug and drain the coolant.

  1. Tighten the radiator drain plug.

  1. Tighten the cylinder block drain plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }


3. REMOVE FRONT BUMPER REINFORCEMENT
  1. for Standard Body: (Click here)
  2. for Wide Body: (Click here)

4. REMOVE W/ RECEIVER CONDENSER ASSEMBLY (w/ Air Conditioning System)
(Click here)

5. REMOVE RADIATOR PROTECTOR (w/o Air Conditioning System)

A316600
  1. Remove the 4 bolts and radiator protector.


6. REMOVE UPPER RADIATOR SUPPORT SEAL

A311096
  1. Remove the 4 clips, 4 bolts and upper radiator support seal.


7. REMOVE RADIATOR RESERVOIR ASSEMBLY

A316482
  1. Slide the hose clamp and disconnect the water by-pass hose from the radiator reservoir assembly.

  1. Slide the hose clamp and disconnect the No. 2 water by-pass hose from the radiator reservoir assembly.

  1. Remove the bolt and radiator reservoir assembly.


8. REMOVE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY

A316480
  1. Disconnect the connector from the windshield washer motor and pump assembly.

  1. Remove the 2 bolts and windshield washer motor and pump assembly.

  1. Detach the hose clamp.

    A316481E01

    Text in Illustration 
    *A
    w/ Rear Wiper
    *B
    w/o Rear Wiper

  1. w/ Rear Wiper:
    Disconnect the 2 connectors and 2 washer hoses.

  1. w/o Rear Wiper:
    Disconnect the connector and washer hose.


9. REMOVE HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY

  1. E289333E01
    Remove the 3 bolts and hood lock support brace sub-assembly.
    Text in Illustration 
    *A
    for Standard Body
    *B
    for Wide Body


10. REMOVE HOOD LOCK ASSEMBLY

A243233
  1. Remove the 3 bolts and disconnect the hood lock assembly.

  1. Disconnect the hood lock assembly from the hood lock control cable assembly.


11. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
  1. Slide the hose clamp and disconnect the water by-pass hose from the radiator assembly.

  1. Detach the 2 clamps to disconnect the hood lock control cable assembly from the upper radiator support sub-assembly.

    A316483E01

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  1. Remove the 6 bolts and upper radiator support sub-assembly.


12. REMOVE NO. 1 RADIATOR AIR GUIDE (for Wide Body)
  1. Remove the 2 bolts and No. 1 radiator air guide.


13. REMOVE NO. 2 RADIATOR AIR GUIDE (for Wide Body)
  1. Remove the 2 bolts and No. 2 radiator air guide.


14. REMOVE FAN BRACKET SUB-ASSEMBLY

A242187
  1. Detach the clamp.

  1. Remove the 2 bolts, 2 nuts and fan bracket sub-assembly.


15. REMOVE FAN SHROUD

  1. A242203E02
    w/ Air Conditioning System:
    Detach the 2 clamps and disconnect the 2 connectors.
    Text in Illustration 
    *A
    w/ Air Conditioning System
    *B
    w/o Air Conditioning System

  1. w/o Air Conditioning System:
    Detach the 3 clamps and disconnect the connector.

  1. A241041
    Remove the 6 bolts and fan shroud from the underside of the vehicle.


16. REMOVE NO. 2 FAN SHROUD
  1. Slide the hose clamp and disconnect the No. 2 water by-pass hose from the water by-pass pipe sub-assembly.

  1. A316614E01
    Remove the bolt to disconnect the water by-pass pipe sub-assembly from the radiator assembly.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

    HINT:
    This procedure is performed because the bolt of the water by-pass pipe sub-assembly interferes with the removal of the No. 2 fan shroud.

  1. A102971E02
    Remove the 2 bolts from the upper side of the vehicle, and then remove the No. 2 fan shroud from the underside of the vehicle.

    HINT:
    Do not damage the radiator assembly when removing the No. 2 fan shroud.


17. REMOVE RADIATOR ASSEMBLY

A316610
  1. Slide the 2 hose clamps and disconnect the No. 2 radiator hose and No. 3 radiator hose from the radiator assembly.

  1. Remove the radiator assembly from the vehicle.

    NOTICE:
    Do not drop the radiator assembly.

  1. Remove the 4 grommets from the radiator assembly.


18. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

A316988
  1. Slide the hose clamp and remove the water by-pass pipe sub-assembly from the radiator assembly.

← COMPONENTS (from Oct 2014)INSTALLATION (from Oct 2014) →