2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Jan 2017


1. INSTALL FUEL SENDER GAUGE ASSEMBLY
  1. Install the fuel hose grommet onto the fuel tank assembly.

  1. Install a new fuel suction tube set gasket, the fuel pump gauge retainer and the fuel sender gauge assembly with the 8 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Install the fuel tank wire, No. 1 fuel evaporation tube sub-assembly, fuel tank main tube sub-assembly and fuel tank return tube sub-assembly onto the fuel sender gauge assembly.


2. INSTALL FUEL TANK ASSEMBLY

  1. A102475J06
    Using the transmission jack, install the 2 fuel tank band sub-assemblies and fuel tank assembly with the 6 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 32 ft.*lbf }

  1. Connect the No. 3 parking brake cable with the bolt.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }


3. CONNECT NO. 3 FUEL HOSE

  1. A102472J09
    Connect the No. 3 fuel hose, and tighten the clamp bolt.


4. INSTALL FUEL HOSE PROTECTOR

  1. A309405
    Install the fuel hose protector to the fuel tank to filler pipe hose and attach the 2 claws.


5. CONNECT FUEL TANK BREATHER TUBE

  1. A102474J06
    Secure the fuel tank breather tube to the fuel tank assembly with the clip.


6. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

  1. A102470J04
    Connect the fuel tank main tube sub-assembly with the clip.


7. CONNECT FUEL TANK RETURN TUBE

  1. A102468J06
    Connect the fuel return tube (Click here).


8. CONNECT FUEL TANK WIRE

  1. A102471E03
    Connect the fuel tank wire.


9. INSTALL PROPELLER SHAFT ASSEMBLY

  1. C102186E01
    Remove the SST from the extension housing.

  1. Install the propeller shaft assembly in the extension housing.

  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. C102185E01
    Install the propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.

    Torque:
    74 N*m{ 755 kgf*cm , 54 ft.*lbf }


10. INSPECT FOR FUEL LEAK

NOTICE:
  1. During Active Test mode, the engine speed becomes high and the combustion noise becomes loud, so pay attention.
  2. During Active Test mode, the fuel pressure becomes high. Be extremely careful not to expose your eyes, hands, or body to escaping fuel.

HINT:
Using the GTS to perform Active Tests allow relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.

  1. Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.

  1. Disconnect the return hose from the common rail assembly.

  1. Start the engine and check for fuel leaks from the return pipe. If there is fuel leakage, replace the common rail assembly.

  1. Perform the Active Test.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak.

    5. If the GTS is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.

    6. Check that there are no leaks from any part of the fuel system.

      HINT:
      A return pipe leakage of less than 10 cc (0.6 cu in.) per minute is acceptable.

      If there is fuel leakage, repair or replace parts as necessary.

  1. Reconnect the return hose to the common rail assembly.

← REMOVAL (from Jan 2017)INSPECTION (from Jan 2017) →