2014-2019 Hiace · Service Manual ENGINE

P0010 Camshaft Position "A" Actuator Circuit (Bank 1)

Diagnostic trouble codes · Vehicles built from Dec 2015

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 from Dec 2015

DESCRIPTION

  1. This DTC is designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the camshaft timing oil control valve duty cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.
  2. The VVT (variable valve timing) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the camshaft timing gear to adjust the valve timing. The camshaft timing oil control valve is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time of the solenoid (duty cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.
A192077E19
DTC No.
DTC Detection Condition
Trouble Area
P0010
Open or short in the camshaft timing oil control valve circuit (1 trip detection logic).
  1. Open or short in camshaft timing oil control valve circuit
  2. Camshaft timing oil control valve assembly
  3. ECM

HINT:
This DTC relates to the camshaft timing oil control valve.


MONITOR DESCRIPTION

The ECM optimizes the valve timing using the VVT system to control the intake camshaft. The VVT system includes the ECM, the OCV and the VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.
After the ECM sends the target duty-cycle signal to the OCV, the ECM monitors the OCV current to establish an actual duty-cycle. The ECM determines the existence of a malfunction and sets the DTC when the actual duty-cycle ratio varies from the target duty-cycle ratio.

WIRING DIAGRAM

A133814E32

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK FOR DTC
  1. Clear the DTCs after recording the freeze frame data and DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Start the engine and allow it to idle. Then check for DTCs.

  1. Check that P0010 is not output.

    OK:
    P0010 is not output.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Inspect the camshaft timing oil control valve assembly (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM)
  1. Disconnect the camshaft timing oil control valve connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D78-2 - D97-74 (OC1+)
    Always
    Below 1 Ω
    D78-1 - D97-96 (OC1-)
    Always
    Below 1 Ω
    D78-2 or D97-74 (OC1+) - Body ground
    Always
    10 kΩ or higher
    D78-1 or D97-96 (OC1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0010 Camshaft Position "A" Actuator Circuit (Bank 1) (Jan 2015 – Nov 2015)P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) (+ P0012) (Oct 2014 – Dec 2014) →