P0617 Starter Relay Circuit High
Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more |
Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic): (a) Vehicle speed is more than 20 km/h (12.5 mph). (b) Engine speed is more than 1000 rpm. (c) STA signal is on. |
|
| DTC No. |
Data List |
| P0617 |
Starter Signal |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (Click here).
- If this DTC is output, inspect the starter.
- The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (Click here).
| 1. READ VALUE USING GTS (STARTER SIGNAL) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the GTS when the ignition switch is turned to ON.
- OK:
Ignition Switch Positions
Starter Signal
ON
OFF
START
ON
| Result |
Proceed to |
| OK |
A |
| NG (for Manual Transmission) |
B |
| NG (for Automatic Transmission) |
C |
|
|
||||
|
|
||||
| C | |
| 2. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Inspect the park/neutral position switch assembly (Click here).
|
|
||||
| OK | |
| 3. INSPECT IGNITION SWITCH |
Inspect the ignition switch (Click here).
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ECM) |
Disconnect the ignition switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H25-1 (ST1) or D88-36 (STA) - Body ground and other terminals
Always
10 kΩ or higher
Reconnect the ignition switch connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 5. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 6. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Replace the park/neutral position switch assembly (Click here).
|
|
||||
| 7. REPLACE IGNITION SWITCH |
Replace the ignition switch.
|
|
||||
| 8. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 9. CONFIRM WHETHER DTC OUTPUT RECURS |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON.
Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
