2014-2019 Hiace · Service Manual ENGINE

P0617 Starter Relay Circuit High

Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.
If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.
P0617 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more
Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.5 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
  1. Starter relay circuit
  2. Ignition switch
  3. Park/neutral position switch assembly*
  4. ECM
*: for Automatic Transmission
Related Data List 
DTC No.
Data List
P0617
Starter Signal

WIRING DIAGRAM

A319602E02
A319501E04

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  3. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  4. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
  1. The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (Click here).
  2. If this DTC is output, inspect the starter.
  3. Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK ENTRY AND START SYSTEM
  1. Confirm the entry and start system.

    Result 
    Result
    Proceed to
    w/o Entry and Start System
    A
    w/ Entry and Start System
    B



B
Go to step 11
A


2. READ VALUE USING GTS (STARTER SIGNAL)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the GTS when the ignition switch is turned to ON.

    OK:
    Ignition Switch Positions
    Starter Signal
    ON
    OFF
    START
    ON

Result 
Result
Proceed to
OK
A
NG (for Manual Transmission)
B
NG (for Automatic Transmission)
C


A
Go to step 10

B
Go to step 4
C


3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly (Click here).



NG
Go to step 7
OK


4. INSPECT IGNITION SWITCH
  1. Inspect the ignition switch (Click here).



NG
Go to step 8
OK


5. CHECK HARNESS AND CONNECTOR
  1. Disconnect the ignition switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H25-1 (ST1) or B72-43 (STA) - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Reconnect the ignition switch connector.

  1. Reconnect the ECM connector.



NG
Go to step 9
OK


6. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 10
7. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Replace the park/neutral position switch assembly (Click here).



NEXT
Go to step 10
8. REPLACE IGNITION SWITCH
  1. Replace the ignition switch (Click here).



NEXT
Go to step 10
9. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


10. CONFIRM WHETHER DTC OUTPUT RECURS
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.

  1. Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.

  1. Confirm that the DTC is not output again.


NEXT

END

11. READ VALUE USING GTS (STARTER SIGNAL)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the GTS when the ignition switch is turned to ON and when the engine is cranking.

    OK:
    Switch Condition
    Starter Signal
    Ignition switch ON
    OFF
    Engine cranking
    ON



NG
Go to step 12
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

12. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
  1. Disconnect the park/neutral position switch assembly connector.

  1. Remove the ST relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 2 or D37-5 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the park/neutral position switch assembly connector.

  1. Reinstall the relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
OK


13. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
  1. Disconnect the park/neutral position switch assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D37-5 or B72-43 (STA) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the park/neutral position switch assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
OK

REPLACE ECM


← P0617 Starter Relay Circuit High (Dec 2015 – Mar 2016)P0617 Starter Relay Circuit High (from Jan 2017) →