2014-2019 Hiace · Service Manual ENGINE

P0335 Crankshaft Position Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016

Also covers:

Versions by build date: Oct 2014 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The crankshaft position sensor system consists of a sensor plate and a pickup coil.
The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.
DTC No.
DTC Detection Condition
Trouble Area
P0335
When either of the following conditions is met (1 trip detection logic):
  1. No crankshaft position sensor signal is sent to the ECM while cranking.
  2. No crankshaft position sensor signal is sent to the ECM at an engine speed of 600 rpm or less.
  3. The crankshaft position sensor signal is missing despite the camshaft position sensor signal inputs being normal after the engine is cranked.
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. No. 2 crankshaft timing sprocket (sensor plate)
  4. Camshaft position sensor
  5. ECM
P0339
All of the following conditions are met (1 trip detection logic):
(a) The engine speed is 1000 rpm or more.
(b) No crankshaft position sensor signal for 0.05 seconds or more.
(c) 3 seconds or more have elapsed since the starter signal switched from ON to OFF.
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft
  4. ECM

  1. A063955E46
    Reference: Inspection using an oscilloscope.

    HINT:
    1. G2 stands for the camshaft position sensor signal and NE stands for the crankshaft position sensor signal.
    2. Grounding failure of the shielded wire may cause noise in the waveforms.

    Tester Connection
    Tool Setting
    Condition
    Specified Condition
    D97-93 (NE+) - D97-117 (NE-)
    5 V/DIV, 20 msec./DIV
    Idling
    The correct waveform is as shown
    D97-94 (G2) - D97-118 (G2-)
    5 V/DIV, 20 msec./DIV
    Idling
    The correct waveform is as shown

MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor.
If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

WIRING DIAGRAM

A247768E05

INSPECTION PROCEDURE

HINT:
After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the camshaft position sensor.
  1. Installation condition of the camshaft position sensor
  2. Installation condition of the camshaft
  3. Connection of the camshaft position sensor connector

HINT:
  1. If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.
  2. The engine speed can be checked by using the intelligent tester. To perform the check, follow the procedures below:
    1. Connect the intelligent tester to the DLC3.
    2. Start the engine.
    3. Turn the intelligent tester on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
    1. The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as less than the actual engine speed if the crankshaft position sensor output voltage is insufficient.
  3. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Start the engine.

  1. Read the values displayed on the intelligent tester while the engine is running.

    Standard:
    Correct values are displayed.

    HINT:
    1. To check the engine speed change, display the graph on the intelligent tester.
    2. If the engine does not start, check the engine speed while cranking.
    3. If the engine speed indicated on the intelligent tester remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
  1. Inspect the crankshaft position sensor (Click here).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D72-1 (NE) - D97-93 (NE+)
    Always
    Below 1 Ω
    D72-2 (NE-) - D97-117 (NE-)
    Always
    Below 1 Ω
    D72-1 (NE) or D97-93 (NE+) - Body ground
    Always
    10 kΩ or higher
    D72-2 (NE-) or D97-117 (NE-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
BR03795E25
  1. Check the crankshaft position sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


5. INSPECT NO. 2 CRANKSHAFT TIMING SPROCKET (TEETH OF SENSOR PLATE)
  1. Check the teeth of the sensor plate.

    OK:
    Sensor plate does not have any cracks or deformation.



NG
REPLACE NO. 2 CRANKSHAFT TIMING SPROCKET (Click here)
OK


6. REPLACE CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).


NEXT


7. CHECK WHETHER DTC OUTPUT RECURS (DTC P0335 AND/OR P0339)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0335 or P0339 is output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END


← P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (Dec 2015 – Mar 2016)P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (from Jan 2017) →