2014-2019 Hiace · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Oct 2014


1. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.3 (NARROW BODY)
  1. Install the parking brake cable assembly No.3 to the parking brake equalizer.

  1. Install the parking brake cable assembly No.3 with the 5 bolts and the nut.

    Torque:
    14.5 N*m{ 148 kgf*cm , 11 ft.*lbf }


    C102158

  1. C102159
    Install the parking brake cable assembly No.3 to the backing plate with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


2. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.3 (WIDE BODY)
  1. Install the parking brake cable assembly No.3 to the parking brake equalizer.

  1. Install the parking brake cable assembly No.3 with the 6 bolts and the nut.

    Torque:
    14.5 N*m{ 148 kgf*cm , 11 ft.*lbf }


    C105462

  1. C102159
    Install the parking brake cable assembly No.3 to the backing plate with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


3. APPLY HIGH TEMPERATURE GREASE

  1. C102609E02
    Apply high temperature grease to the shoe attached surface of the backing plate.
    Text in Illustration 
    *1
    High temperature grease


4. INSTALL REAR BRAKE SHOE

  1. for 254 mm drum:

    1. C102607E02
      Using pliers, install the rear brake shoe, shoe strut set, rear cushion lever and shoe lever with a new C-washer.
      Text in Illustration 
      *1
      Brake Shoe Lever
      *2
      Brake Shoe Strut Set
      *3
      Rear Brake Shoe
      *4
      Rear Cushion Lever
      *5
      C-washer

    2. C102606
      Connect the parking brake cable No. 3 to the front brake shoe.

    3. C102603E01
      Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  

  1. for 295 mm drum:

    1. C263530E01
      Install the rear brake shoe, brake shoe strut set and shoe lever with a new C-washer.
      Text in Illustration 
      *1
      Rear Brake Shoe
      *2
      Brake Shoe Strut Set
      *3
      Brake Shoe Lever
      *4
      Automatic Adjust Lever
      *5
      C-washer
      *6
      E-ring

    2. Install a new E-ring and the automatic adjust lever.

    3. C263529
      Connect the parking brake cable No. 3 to the front brake shoe.

    4. C263525
      Install the tension spring as shown in the illustration.

    5. C263528E01
      Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  


5. INSTALL FRONT BRAKE SHOE

  1. for 254 mm drum:

    1. Install the return spring to each brake shoe.

    2. C102604E01
      Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  

    3. C264855E02
      Install the brake shoe lower strut.
      Text in Illustration 
      *A
      LH Side
      *B
      RH Side

      NOTICE:
      Make sure that the shoe lower strut and brake rear cushion lever are securely engaged.

    4. C102600
      Using needle-nose pliers, install the tension spring.

  1. for 295 mm drum:

    1. C263527E01
      Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  

    2. Install the return spring to each brake shoe.


6. CONNECT PARKING BRAKE SHOE STRUT SET

  1. for 254 mm drum:

    1. C231698E01
      Using SST, install the upper side tension spring.
      SST
      09703-30011  

  1. for 295 mm drum:

    1. C263526E01
      Using SST, install the upper side tension spring.
      SST
      09703-30011  


7. INSTALL AUTOMATIC ADJUST LEVER

  1. for 254 mm drum:

    1. C102605
      Install the automatic adjust lever and tension spring.

      NOTICE:
      Make sure to install the automatic adjust lever between the groove of the shoe strut set and brake shoe.


8. INSTALL REAR AXLE BRAKE DRUM GASKET

9. INSTALL REAR BRAKE DRUM

10. INSPECT PARKING BRAKE CONTROL HANDLE TRAVEL
  1. Pull firmly on the parking brake control handle.

  1. Release the parking brake lock, and return the parking brake control handle to its off position.

  1. Slowly pull the parking brake control handle all the way up, and count the number of clicks.

    Parking brake control handle travel:
    10 to 16 clicks at 200 N (20 kgf, 44 lbf) (except Super Long Wheelbase)
    12 to 18 clicks at 200 N (20 kgf, 44 lbf) (for Super Long Wheelbase)

    HINT:
    1. If the number of clicks falls outside of the specified range, release the parking brake lock and adjust it.
    2. If there are fewer clicks than the specified value, loosen the parking brake wire adjustment nut an the lock nut. With the parking brake cable loosened, adjust the clearance between the brake drum and lining.


11. REMOVE REAR WHEEL

12. ADJUST REAR BRAKE SHOE CLEARANCE

  1. Using a screwdriver from a service hole, turn the adjuster to expand the shoes so that the brake shoes touch the brake drum.

    C263542E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

  1. Using another screwdriver, push up the automatic adjust lever and turn the adjuster to contract the shoes so that the brake shoe does not touch the brake drum. Then turn the adjuster another 180 degrees to further contract the shoes.

    C263541E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

  1. Install the hole plug.


13. INSTALL REAR WHEEL

Torque:
100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }


14. ADJUST PARKING BRAKE CONTROL HANDLE TRAVEL
  1. Lift the vehicle

  1. C102142E01
    Depress the parking brake handle. Hold the parking brake adjusting nut using a wrench, and loosen the lock nut.

  1. Turn the parking brake adjusting nut until the parking brake handle travel meets the above specification.

    Parking brake control handle travel:
    10 to 16 clicks at 200 N (20 kgf, 44 lbf) (except Super Long Wheelbase)
    12 to 18 clicks at 200 N (20 kgf, 44 lbf) (for Super Long Wheelbase)

  1. Count the number of clicks after depressing and releasing the parking brake control handle 3 or 4 times.

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake control handle, check that the parking brake indicator light comes on.

    Standard:
    Brake warning light always comes on at the first click.

  1. Hold the parking brake adjusting nut using a wrench, and tighten the lock nut.

    Torque:
    14.5 N*m{ 148 kgf*cm , 11 ft.*lbf }

  1. Lower the vehicle.

← REMOVAL (from Oct 2014)ON-VEHICLE INSPECTION (from Oct 2014) →